American Hearth Natural Gas to Propane Conversion Kit for the Renegade Inserts Owner's manual

Brand: American Hearth

Model: Natural Gas to Propane Conversion Kit for the Renegade Inserts

Type: Owner's manual

37918-1-0719 Page 1

WARNING

This conversion kit must be installed by an Empire Comfort Systems, distributor (or other

          









WARNING







Intermittent Pilot System

1. Turn "OFF" using remote control. Main burner and pilot should go off.

2. Pilot gas ow should stop within 30 seconds.





Conversion Kits

Quantity Supplied

 

Main Burner Orice, Front P326 (#59) P320 (#57) 1

Main Burner Orice, Rear P312 (1.20 mm) P308 (1.40 mm) 1

SIT Gas Valve Conversion Kit

R11382 R11382 1

Gas Conversion Label 1224 1224 1



• Standard screwdriver

• 1/4 inch hex driver

• 5/16 inch hex driver

• 7/16-inch wrench

• 7/16 inch deep socket



DVCT30CBN95P - 28,500 BTU per hour DVCT35CBN95P - 35,000 BTU per hour

The direct-vent gas replace when converted to Propane Gas will have a manifold pressure of approximately 10.0 inches

w.c. (2.49kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 10.8 inches w.c. (2.68kPa) for the

purpose of input adjustment to a maximum of 14.0 inches w.c. (3.484kPa).







FOR CONVERSION TO

37918-1-0719Page 2



1. If replace is installed, turn OFF gas and electric supply to

replace before making gas conversion. Allow replace to

cool completely.

2. Remove barrier screen, glass door, logs and embers, and

liners. 





3. Remove front and rear burners by removing screws on left

and pulling out towards left side. 



4. Remove (2) screws holding pilot assembly to burner pan.

This will allow pilot assembly to drop. 



5. Remove (2) screws holding burner base in place. Lift burner

base out of rebox. 





Use needle-nose pliers to remove targets by rotating them

counterclockwise and discard. 

TARGET



7. Use a 7/16 inch deep socket wrench to remove front and

rear orices.

37918-1-0719 Page 3

8a.

Use a 7/16 inch deep socket wrench to install orice

marked 1.20 mm in rear orice holder and #59 in front

orice holder (30 only).

8b.

Use a 7/16 inch deep socket wrench to install orice

marked 1.40 mm in rear orice holder and #57 in front

orice holder (35 only).



9. Loosen rear air shutter screw and rotate handle to the right

until full open is achieved. Tighten screw. 

10. Loosen the front air shutter screw and lower the air shutter

until it stops. Then tighten the screw. 



OPEN

CLOSED



CLOSED

OPEN



11. Using a 7/16 inch open wrench, loosen pilot body by slightly

turning counter-clockwise. Slide orice bracket to other side

and tighten pilot body clockwise. 



12. Replace items removed in steps 2-5 in reverse order.

13. Adjust damper and air shutter for perfect burn.

14. Gas conversion completed.

Check the main burner ame and pilot burner ame for proper

ame characteristics, as outlined in the Installation Instructions.



Check the input of the replace.

1. Turn off all other gas appliances. Clock the gas meter and

determine the number of seconds required to consume one

cubic foot of gas.

2. 3600 ÷ time (in seconds) = cu. Ft. per hour.

3. Then cu. Ft. per hour x heating value of gas = input rate

(Btu/hr). On installation without gas meters, check manifold

for proper pressure.

If replace is not installed or product card has not been returned

to Empire Comfort System’s, check off type of gas converted to

on the card. Also indicate conversion by adding “Conv.” behind

type of gas.

NAT

ORIFICE

37918-1-0719Page 4







If you have a general question

about our products, please e-mail

us at [email protected].

If you have a service or repair

question, please contact your dealer.

American Hearth Natural Gas to Propane Conversion Kit for the Renegade Inserts Owner's manual

American Hearth Natural Gas to Propane Conversion Kit for the Renegade Inserts Owner's manual

American Hearth Natural Gas to Propane Conversion Kit for the Renegade Inserts Owner's manual

Related papers

Other documents