37918-1-0719 Page 1
WARNING
This conversion kit must be installed by an Empire Comfort Systems, distributor (or other
WARNING
Intermittent Pilot System
1. Turn "OFF" using remote control. Main burner and pilot should go off.
2. Pilot gas ow should stop within 30 seconds.
Conversion Kits
Quantity Supplied
Main Burner Orice, Front P326 (#59) P320 (#57) 1
Main Burner Orice, Rear P312 (1.20 mm) P308 (1.40 mm) 1
SIT Gas Valve Conversion Kit
R11382 R11382 1
Gas Conversion Label 1224 1224 1
• Standard screwdriver
• 1/4 inch hex driver
• 5/16 inch hex driver
• 7/16-inch wrench
• 7/16 inch deep socket
DVCT30CBN95P - 28,500 BTU per hour DVCT35CBN95P - 35,000 BTU per hour
The direct-vent gas replace when converted to Propane Gas will have a manifold pressure of approximately 10.0 inches
w.c. (2.49kPa) at the valve outlet with the inlet pressure to the valve from a minimum of 10.8 inches w.c. (2.68kPa) for the
purpose of input adjustment to a maximum of 14.0 inches w.c. (3.484kPa).
FOR CONVERSION TO
37918-1-0719Page 2
1. If replace is installed, turn OFF gas and electric supply to
replace before making gas conversion. Allow replace to
cool completely.
2. Remove barrier screen, glass door, logs and embers, and
liners.
3. Remove front and rear burners by removing screws on left
and pulling out towards left side.
2
1
.
4. Remove (2) screws holding pilot assembly to burner pan.
This will allow pilot assembly to drop.
5. Remove (2) screws holding burner base in place. Lift burner
base out of rebox.
6.
Use needle-nose pliers to remove targets by rotating them
counterclockwise and discard.
TARGET
7. Use a 7/16 inch deep socket wrench to remove front and
rear orices.
37918-1-0719 Page 3
8a.
Use a 7/16 inch deep socket wrench to install orice
marked 1.20 mm in rear orice holder and #59 in front
orice holder (30 only).
8b.
Use a 7/16 inch deep socket wrench to install orice
marked 1.40 mm in rear orice holder and #57 in front
orice holder (35 only).
9. Loosen rear air shutter screw and rotate handle to the right
until full open is achieved. Tighten screw.
10. Loosen the front air shutter screw and lower the air shutter
until it stops. Then tighten the screw.
OPEN
CLOSED
CLOSED
OPEN
11. Using a 7/16 inch open wrench, loosen pilot body by slightly
turning counter-clockwise. Slide orice bracket to other side
and tighten pilot body clockwise.
12. Replace items removed in steps 2-5 in reverse order.
13. Adjust damper and air shutter for perfect burn.
14. Gas conversion completed.
Check the main burner ame and pilot burner ame for proper
ame characteristics, as outlined in the Installation Instructions.
Check the input of the replace.
1. Turn off all other gas appliances. Clock the gas meter and
determine the number of seconds required to consume one
cubic foot of gas.
2. 3600 ÷ time (in seconds) = cu. Ft. per hour.
3. Then cu. Ft. per hour x heating value of gas = input rate
(Btu/hr). On installation without gas meters, check manifold
for proper pressure.
If replace is not installed or product card has not been returned
to Empire Comfort System’s, check off type of gas converted to
on the card. Also indicate conversion by adding “Conv.” behind
type of gas.
NAT
NAT
ORIFICE
37918-1-0719Page 4
If you have a general question
about our products, please e-mail
us at [email protected].
If you have a service or repair
question, please contact your dealer.
/