DSC Power432 User manual

Brand: DSC

Model: Power432

Category: Fire protection

Type: User manual

Toronto, Canada • www.dsc.com

Printed in Canada 29034581 R001

Direct all comments and suggestions

concerning DSC publications to

[email protected]

Instruction

Manual

W A R N I N G

This manual contains information on limitations regarding product use and function and

information on the limitations as to liability of the manufacturer.

The entire manual should be carefully read.

PC580

WARNING Please Read Carefully

Note to Installers

This warning contains vital information. As the only individual in contact

with system users, it is your responsibility to bring each item in this warn-

ing to the attention of the users of this system.

System Failures

This system has been carefully designed to be as effective as possible. There

are circumstances, however, involving fire, burglary, or other types of emer-

gencies where it may not provide protection. Any alarm system of any type

may be compromised deliberately or may fail to operate as expected for a

variety of reasons. Some but not all of these reasons may be:

■ ■

■ Inadequate Installation

A security system must be installed properly in order to provide adequate

protection. Every installation should be evaluated by a security profes-

sional to ensure that all access points and areas are covered. Locks and

latches on windows and doors must be secure and operate as intended.

Windows, doors, walls, ceilings and other building materials must be of

sufficient strength and construction to provide the level of protection

expected. A reevaluation must be done during and after any construction

activity. An evaluation by the fire and/or police department is highly recom-

mended if this service is available.

■ ■

■ Criminal Knowledge

This system contains security features which were known to be effective at

the time of manufacture. It is possible for persons with criminal intent to

develop techniques which reduce the effectiveness of these features. It is

important that a security system be reviewed periodically to ensure that its

features remain effective and that it be updated or replaced if it is found that

it does not provide the protection expected.

■ ■

■ Access by Intruders

Intruders may enter through an unprotected access point, circumvent a

sensing device, evade detection by moving through an area of insuffi-

cient coverage, disconnect a warning device, or interfere with or pre-

vent the proper operation of the system.

■ ■

■ Power Failure

Control units, intrusion detectors, smoke detectors and many other security

devices require an adequate power supply for proper operation. If a device

operates from batteries, it is possible for the batteries to fail. Even if the

batteries have not failed, they must be charged, in good condition and in-

stalled correctly. If a device operates only by AC power, any interruption,

however brief, will render that device inoperative while it does not have

power. Power interruptions of any length are often accompanied by voltage

fluctuations which may damage electronic equipment such as a security sys-

tem. After a power interruption has occurred, immediately conduct a com-

plete system test to ensure that the system operates as intended.

■ ■

■ Failure of Replaceable Batteries

This system’s wireless transmitters have been designed to provide several

years of battery life under normal conditions. The expected battery life is a

function of the device environment, usage and type. Ambient conditions

such as high humidity, high or low temperatures, or large temperature fluc-

tuations may reduce the expected battery life. While each transmitting de-

vice has a low battery monitor which identifies when the batteries need to

be replaced, this monitor may fail to operate as expected. Regular testing and

maintenance will keep the system in good operating condition.

■ ■

■ Compromise of Radio Frequency (Wireless) Devices

Signals may not reach the receiver under all circumstances which could

include metal objects placed on or near the radio path or deliberate

jamming or other inadvertent radio signal interference.

■■

■ System Users

A user may not be able to operate a panic or emergency switch possibly due

to permanent or temporary physical disability, inability to reach the device

in time, or unfamiliarity with the correct operation. It is important that all

system users be trained in the correct operation of the alarm system and that

they know how to respond when the system indicates an alarm.

■ ■

■ Smoke Detectors

Smoke detectors that are a part of this system may not properly alert occupants of

a fire for a number of reasons, some of which follow. The smoke detectors may have

been improperly installed or positioned. Smoke may not be able to reach the

smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the

other side of closed doors. Smoke detectors may not detect smoke from fires on

another level of the residence or building.

Every fire is different in the amount of smoke produced and the rate of burning.

Smoke detectors cannot sense all types of fires equally well. Smoke detectors may

not provide timely warning of fires caused by carelessness or safety hazards such

as smoking in bed, violent explosions, escaping gas, improper storage of flam-

mable materials, overloaded electrical circuits, children playing with matches or

arson.

Even if the smoke detector operates as intended, there may be circumstances when

there is insufficient warning to allow all occupants to escape in time to avoid

injury or death.

■ ■

■ Motion Detectors

Motion detectors can only detect motion within the designated areas as shown

in their respective installation instructions. They cannot discriminate between

intruders and intended occupants. Motion detectors do not provide volumetric

area protection. They have multiple beams of detection and motion can only be

detected in unobstructed areas covered by these beams. They cannot detect

motion which occurs behind walls, ceilings, floor, closed doors, glass partitions,

glass doors or windows. Any type of tampering whether intentional or unin-

tentional such as masking, painting, or spraying of any material on the lenses,

mirrors, windows or any other part of the detection system will impair its proper

operation.

Passive infrared motion detectors operate by sensing changes in temperature.

However their effectiveness can be reduced when the ambient temperature rises

near or above body temperature or if there are intentional or unintentional sources

of heat in or near the detection area. Some of these heat sources could be heaters,

radiators, stoves, barbeques, fireplaces, sunlight, steam vents, lighting and so

on.

■ ■

■ Warning Devices

Warning devices such as sirens, bells, horns, or strobes may not warn

people or waken someone sleeping if there is an intervening wall or door.

If warning devices are located on a different level of the residence or premise,

then it is less likely that the occupants will be alerted or awakened. Au-

dible warning devices may be interfered with by other noise sources such

as stereos, radios, televisions, air conditioners or other appliances, or

passing traffic. Audible warning devices, however loud, may not be heard

by a hearing-impaired person.

■ ■

■ Telephone Lines

If telephone lines are used to transmit alarms, they may be out of service or busy

for certain periods of time. Also an intruder may cut the telephone line or defeat

its operation by more sophisticated means which may be difficult to detect.

■ ■

■ Insufficient Time

There may be circumstances when the system will operate as intended, yet the

occupants will not be protected from the emergency due to their inability to

respond to the warnings in a timely manner. If the system is monitored, the

response may not occur in time to protect the occupants or their belongings.

■ ■

■ Component Failure

Although every effort has been made to make this system as reliable as possible,

the system may fail to function as intended due to the failure of a component.

■ ■

■ Inadequate Testing

Most problems that would prevent an alarm system from operating as in-

tended can be found by regular testing and maintenance. The complete sys-

tem should be tested weekly and immediately after a break-in, an attempted

break-in, a fire, a storm, an earthquake, an accident, or any kind of construc-

tion activity inside or outside the premises. The testing should include all

sensing devices, keypads, consoles, alarm indicating devices and any other

operational devices that are part of the system.

■ ■

■ Security and Insurance

Regardless of its capabilities, an alarm system is not a substitute for prop-

erty or life insurance. An alarm system also is not a substitute for property

owners, renters, or other occupants to act prudently to prevent or mini-

mize the harmful effects of an emergency situation.

or repaired in such a manner as to adversely affect performance or

prevent adequate inspection or testing to verify any warranty claim.

Access cards or tags returned for replacement under warranty will be

credited or replaced at DSC's option. Products not covered by this

warranty, or otherwise out of warranty due to age, misuse, or damage

shall be evaluated, and a repair estimate shall be provided. No repair

work will be performed until a valid purchase order is received from

the Customer and a Return Merchandise Authorisation number (RMA)

is issued by DSC's Customer Service.

Digital Security Controls Ltd.’s liability for failure to repair the product

under this warranty after a reasonable number of attempts will be limited

to a replacement of the product, as the exclusive remedy for breach of

warranty. Under no circumstances shall Digital Security Controls Ltd.

be liable for any special, incidental, or consequential damages based

upon breach of warranty, breach of contract, negligence, strict liability,

or any other legal theory. Such damages include, but are not limited to,

loss of profits, loss of the product or any associated equipment, cost of

capital, cost of substitute or replacement equipment, facilities or services,

down time, purchaser’s time, the claims of third parties, including

customers, and injury to property. The laws of some jurisdictions limit

or do not allow the disclaimer of consequential damages. If the laws of

such a jurisdiction apply to any claim by or against DSC, the limitations

and disclaimers contained here shall be to the greatest extent permitted

by law. Some states do not allow the exclusion or limitation of incidental

or consequential damages, so that the above may not apply to you.

Disclaimer of Warranties

This warranty contains the entire warranty and shall be in lieu of

any and all other warranties, whether expressed or implied (includ-

ing all implied warranties of merchantability or fitness for a particu-

lar purpose) and of all other obligations or liabilities on the part of

Digital Security Controls Ltd. Digital Security Controls Ltd. neither

assumes responsibility for nor authorizes any other person purport-

ing to act on its behalf to modify or to change this warranty, nor to

assume for it any other warranty or liability concerning this product.

This disclaimer of warranties and limited warranty are governed

by the laws of the province of Ontario, Canada.

WARNING: Digital Security Controls Ltd. recommends that

the entire system be completely tested on a regular basis. How-

ever, despite frequent testing, and due to, but not limited to,

criminal tampering or electrical disruption, it is possible for

this product to fail to perform as expected.

Out of Warranty Repairs

Digital Security Controls Ltd. will at its option repair or replace out-of-

warranty products which are returned to its factory according to the

following conditions. Anyone returning goods to Digital Security Con-

trols Ltd. must first obtain an authorization number. Digital Security

Controls Ltd. will not accept any shipment whatsoever for which prior

authorization has not been obtained.

Products which Digital Security Controls Ltd. determines to be re-

pairable will be repaired and returned. A set fee which Digital Security

Controls Ltd. has predetermined and which may be revised from time

to time, will be charged for each unit repaired.

Products which Digital Security Controls Ltd. determines not to be

repairable will be replaced by the nearest equivalent product avail-

able at that time. The current market price of the replacement prod-

uct will be charged for each replacement unit.

LIMITED WARRANTY

Digital Security Controls Ltd. warrants the original purchaser that

for a period of twelve months from the date of purchase, the product

shall be free of defects in materials and workmanship under normal

use. During the warranty period, Digital Security Controls Ltd.

shall, at its option, repair or replace any defective product upon

return of the product to its factory, at no charge for labour and

materials. Any replacement and/or repaired parts are warranted for

the remainder of the original warranty or ninety (90) days, whichever

is longer. The original purchaser must promptly notify Digital

Security Controls Ltd. in writing that there is defect in material or

workmanship, such written notice to be received in all events prior

to expiration of the warranty period. There is absolutely no warranty

on software and all software products are sold as a user license under

the terms of the software license agreement included with the product.

The Customer assumes all responsibility for the proper selection,

installation, operation and maintenance of any products purchased

from DSC. Custom products are only warranted to the extent that

they do not function upon delivery. In such cases, DSC can replace

or credit at its option.

International Warranty

The warranty for international customers is the same as for any

customer within Canada and the United States, with the exception

that Digital Security Controls Ltd. shall not be responsible for any

customs fees, taxes, or VAT that may be due.

Warranty Procedure

To obtain service under this warranty, please return the item(s) in

question to the point of purchase. All authorized distributors and

dealers have a warranty program. Anyone returning goods to Digi-

tal Security Controls Ltd. must first obtain an authorization num-

ber. Digital Security Controls Ltd. will not accept any shipment

whatsoever for which prior authorization has not been obtained.

Conditions to Void Warranty

This warranty applies only to defects in parts and workmanship

relating to normal use. It does not cover:

• damage incurred in shipping or handling;

• damage caused by disaster such as fire, flood, wind, earthquake or

lightning;

• damage due to causes beyond the control of Digital Security Controls

Ltd. such as excessive voltage, mechanical shock or water damage;

• damage caused by unauthorized attachment, alterations, modifications

or foreign objects;

• damage caused by peripherals (unless such peripherals were supplied

by Digital Security Controls Ltd.);

• defects caused by failure to provide a suitable installation environment

for the products;

• damage caused by use of the products for purposes other than those for

which it was designed;

• damage from improper maintenance;

• damage arising out of any other abuse, mishandling or improper

application of the products.

Items Not Covered by Warranty

In addition to the items which void the Warranty, the following

items shall not be covered by Warranty: (i) freight cost to the repair

centre; (ii) products which are not identified with DSC's product

label and lot number or serial number; (iii) products disassembled

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls

Ltd. could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interfer-ence in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be deter-mined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: "How to Identify and

Resolve Radio/Television Interference Problems". This booklet is available from the U.S.

Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules and the requirements adopted by

the ACTA. On the side of this equipment is a label that contains, among other information,

a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must

be provided to the Telephone Company.

Product identifier: US: F53AL01BPC580

USOC Jack: RJ-31X

Telephone Connection Requirements

A plug and jack used to connect this equipment to the premises wiring and telephone

network must comply with the applicable FCC Part 68 rules and requirements adopted by

the ACTA. A compliant telephone cord and modular plug is provided with this product. It

is designed to be connected to a compatible modular jack that is also compliant. See

installation instructions for details.

Ringer Equivalence Number (REN)

The REN is used to determine the number of devices that may be connected to a telephone

line. Excessive RENs on a telephone line may result in the devices not ringing in response

to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0).

To be certain of the number of devices that may be connected to a line, as determined by

the total RENs, contact the local Telephone Company. For products approved after July 23,

2001, the REN for this product is part of the product identifier that has the format

US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point

(e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

Incidence of Harm

If this equipment PC580 causes harm to the telephone network, the telephone company will

notify you in advance that temporary discontinuance of service may be required. But if

advance notice is not practical, the Telephone Company will notify the customer as soon

as possible. Also, you will be advised of your right to file a complaint with the FCC if you

believe it is necessary.

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equipment, operations or

procedures that could affect the operation of the equipment. If this happens the Telephone

Company will provide advance notice in order for you to make necessary modifications

to maintain uninterrupted service.

Equipment Maintenance Facility

If trouble is experienced with this equipment PC580, for repair or warranty information,

please contact the facility indicated below. If the equipment is causing harm to the

telephone network, the Telephone Company may request that you disconnect the equipment

until the problem is solved. This equipment is of a type that is not intended to be repaired

by the end user. Simplex Time Recorder Co. 100 Simplex Drive, Westminster MA 01441-

0001 USA, Tel: (978) 731-2500.

Additional Information

Connection to party line service is subject to state tariffs. Contact the state public utility

commission, public service commission or corporation commission for information.

Alarm dialing equipment must be able to seize the telephone line and place a call in an

emergency situation. It must be able to do this even if other equipment (telephone,

answering system, computer modem, etc.) already has the telephone line in use. To do so,

alarm dialing equipment must be connected to a properly installed RJ-31X jack that is

electrically in series with and ahead of all other equipment attached to the same telephone

line. Proper installation is depicted in the figure below. If you have any questions

concerning these instructions, you should consult your telephone company or a qualified

installer about installing the RJ-31X jack and alarm dialing equipment for you.

Telephone

Computer

Telephone

Fax Machine

Alarm Dialing

Equipment

RJ-31X

Jack

Unused

RJ-11 Jack

Telephone

Line

Network

Service

Provider's

Facilities

Customer Premises Equipment and Wiring

Unused

RJ-11 Jack

Network

Demarcation

Point

Answering

System

IC: 160A - PC580

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment

Technical Specifications. This is confirmed by the registration number. The abbreviation,

IC, before the registration number signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada technical specifications were

met. It does not imply that Industry Canada approved the equipment.

NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The

REN assigned to each terminal equipment provides an indication of the maximum number

of terminals allowed to be connected to a telephone interface. The termination on an

interface may consist of any combination of devices subject only to the requirement that

the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

About Your Security System

Your DSC security equipment has been designed to provide you with the greatest possible flexibility

and convenience. Read this manual carefully and have your installer instruct you on your system’s

operation and on which features have been implemented in your system. All users of this system

should be equally instructed in its use. Fill out the “System Information” page with all of your zone

information and access codes and store this manual in a safe place for future reference.

Fire Detection

This equipment is capable of monitoring fire detection devices such as smoke detectors and providing

a warning if a fire condition is detected. Good fire detection depends on having adequate number of

detectors placed in appropriate locations. This equipment should be installed in accordance with

N.F.P.A. standard #72. (N.F.P.A., Batterymarch Park, Quincey MA 02269). Carefully review the Family

Escape Planning guidelines in this manual.

NOTE: Your installer must enable the fire detection portion of this equipment before it will work.

Testing

To insure that your system continues to work as intended, you must test your system weekly. Please

refer to “Testing Your System” on page 13 of this manual. If your system does not work properly, call

your installing company for service.

Monitoring

This system is capable of sending alarms, troubles and emergency information over telephone lines to

a monitoring station. If you inadvertently initiate an alarm, immediately call the monitoring station to

prevent an unnecessary response.

NOTE: Your installer must enable the monitoring feature before it will work.

General System Operation

Your security system is made up of a DSC control panel, one or more keypads and various sensors

and detectors. The control panel will be mounted out of the way in a utility closet or in a basement. The

metal cabinet contains the system electronics, fuses and stand-by battery. There is normally no reason

for anyone but the installer or service professional to have access to the control panel.

All the keypads have an audible indicator and command entry keys. The LED keypads have a group

of zone and system status lights. The LCD keypad has an alphanumeric liquid crystal display (LCD).

The keypad is used to send commands to the system and to display the current system status. The

keypad(s) will be mounted in a convenient location inside the protected premises close to the entry/

exit door(s).

The security system has several protected areas (zones) and each of these will be connected to one

or more sensors (motion detectors, glassbreak detectors, door contacts, etc.). A sensor in alarm will

be indicated by the corresponding zone lights flashing on an LED keypad or by a fixed message on

the LCD keypad.

IMPORTANT NOTICE

A security system cannot prevent emergencies. It is only intended to alert you and – if included –

your monitoring station of an emergency situation. Security systems are generally very reliable

but they may not work under all conditions and they are not a substitute for prudent security

practices or life and property insurance. Your security system should be installed and serviced by

qualified security professionals who should instruct you on the level of protection that has been

provided and on system operations.

System Information

Fill out the following information for future reference and store this manual in a safe place.

Access Codes

Your Master Code is:__________________________________________

Additional Access Codes:

01 __________________ 09 ____________________ 17 ____________________ 25 ________________

02 __________________ 10 ____________________ 18 ____________________ 26 ________________

03 __________________ 11 ____________________ 19 ____________________ 27 ________________

04 __________________ 12 ____________________ 20 ____________________ 28 ________________

05 __________________ 13 ____________________ 21 ____________________ 29 ________________

06 __________________ 14 ____________________ 22 ____________________ 30 ________________

07 __________________ 15 ____________________ 23 ____________________ 31 ________________

08 __________________ 16 ____________________ 24 ____________________ 32 ________________

Zone Information

There are ________ active zones on the system.

Zone Protected Area Zone Type

1 ___________________________________________ _____________________________________

2 ___________________________________________ _____________________________________

3 ___________________________________________ _____________________________________

4 ___________________________________________ _____________________________________

5 ___________________________________________ _____________________________________

6 ___________________________________________ _____________________________________

7 ___________________________________________ _____________________________________

8 ___________________________________________ _____________________________________

9 ___________________________________________ _____________________________________

10 ___________________________________________ _____________________________________

11 ___________________________________________ _____________________________________

12 ___________________________________________ _____________________________________

13 ___________________________________________ _____________________________________

14 ___________________________________________ _____________________________________

Fire Escape Planning

There is often very little time between the detection of a fire and the time it becomes deadly. It is thus

very important that a family escape plan be developed and rehearsed.

1. Every family member should participate in developing the escape plan.

2. Study the possible escape routes from each location within the house. Since many fires occur at

night, special attention should be given to the escape routes from sleeping quarters.

3. Escape from a bedroom must be possible without opening the interior door.

Consider the following when making your escape plans:

• Make sure that all perimeter doors and windows are easily opened. Ensure that they are not

painted shut, and that their locking mechanisms operate smoothly.

• If opening or using the exit is too difficult for children, the elderly or handicapped, plans for rescue

should be developed. This includes making sure that those who are to perform the rescue can

promptly hear the fire warning signal.

• If the exit is above the ground level, an approved fire ladder or rope should be provided as well as

training in its use.

• Exits on the ground level should be kept clear. Be sure to remove snow from exterior patio doors in

winter; outdoor furniture or equipment should not block exits.

• Each person should know of a predetermined assembly point where everyone could be accounted

for i.e.: across the street or at a neighbour’s house. Once everyone is out of the building, call the

Fire Department.

• A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not

gather belongings or pets as this wastes valuable time. Once outside, do not re-enter the house.

Wait for the fire department.

• Write the fire escape plan down and rehearse it frequently so that should an emergency arise,

everyone will know what to do. Revise the plan as conditions change, such as the number of

people in the home, or if there are changes to the building’s construction.

• Make sure your fire warning system is operational by conducting weekly tests (see “Testing Your

System” on page 13). If you are unsure about system operation, contact your installing dealer.

• We recommend that you contact your local fire department and request further information on fire

safety and escape planning. If available, have your local fire prevention officer conduct an in-

house fire safety inspection.

Maintenance

With normal use, the system requires minimum maintenance. The following points should be observed.

1.Do not wash the security station with a wet cloth. Light dusting with a slightly moistened cloth should

remove normal accumulations of dust.

2.The battery/bell test is designed to determine battery condition. We recommended, however, that the

stand-by batteries be replaced every three years.

3.For other system devices such as smoke detectors, passive infrared, ultrasonic or microwave motion

detectors or glassbreak detectors, consult the respective manufacturer’s literature for testing and

maintenance.

Press (*) For <>

Output Control

Select Output <>

Command Output #1

Select Output <>

Command Output #2

To activate the door chime from an LCD Keypad:

Press [✱] to enter the function list, then scroll to find...

Press [✱] or [4] to enable or disable the Door Chime feature. Press [#] to return to the

Ready state.

Fire Alarm Operation

NOTE: The description below may not be applicable depending on how your installer has

programmed the fire alarm operations on your system. Ask your installer for more information

regarding your system’s operation.

Alarm

During a fire alarm, the bell or siren will pulse ON and OFF. The transmission of the alarm to the

monitoring station is delayed for 30 seconds. If the alarm is not cleared within the 30-second delay, it will

be transmitted to the monitoring station.

Silence

To silence the bell or siren, press the [#] key. If the alarm is silenced and the smoke detector is not

reset, the alarm will resound after 90 seconds.

Resetting Smoke Detectors

Once the smoke detector is reset, if it still detects smoke, the alarm sequence will resound as described

above. If there is no smoke, the system will return to normal.

To reset smoke detectors from an LED or Fixed Message LCD5501Z keypad:

Press [✱][7][2].

To reset smoke detectors from an LCD Keypad:

Press [✱] to enter the function list. Scroll to find:

Press [✱] to select the output control. The display will read...

Use the arrow (< >) keys to find the following message and press the [✱] key to

select...

NOTE: If you suspect that a fire alarm has transmitted and that there is no fire condition, call the

monitoring station to avoid an unnecessary response.

If a fire condition is apparent, follow your

evacuation plan immediately. If the alarm sounds at night, evacuate immediately.

Household Fire Safety Audit

Most fires occur in the home. To minimize this danger, we recommend that a household fire safety audit

is conducted and a fire escape plan is developed.

1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded

lighting circuits, etc. If you are uncertain about the condition of your electrical appliances or

household service, have a professional evaluate these units.

2. Are all flammable liquids stored safely in closed containers in a well-ventilated cool area? Cleaning

with flammable liquids should be avoided.

3. Are fire hazardous materials (matches) well out of reach of children?

4. Are furnaces and wood burning appliances properly installed, clean and in good working order?

Have a professional evaluate these appliances.

Press (*) For<>

Door Chime

15 ___________________________________________ _____________________________________

16 ___________________________________________ _____________________________________

17 ___________________________________________ _____________________________________

18 ___________________________________________ _____________________________________

19 ___________________________________________ _____________________________________

20 ___________________________________________ _____________________________________

21 ___________________________________________ _____________________________________

22 ___________________________________________ _____________________________________

23 ___________________________________________ _____________________________________

24 ___________________________________________ _____________________________________

25 ___________________________________________ _____________________________________

26 ___________________________________________ _____________________________________

27 ___________________________________________ _____________________________________

28 ___________________________________________ _____________________________________

29 ___________________________________________ _____________________________________

30 ___________________________________________ _____________________________________

31 ___________________________________________ _____________________________________

32 ___________________________________________ _____________________________________

[F] FIRE __________________________________________

[A] AUXILIARY ____________________________________

[P] PANIC ________________________________________

The Exit Delay Time is________ seconds.

The Entry Delay Time is ______ seconds.

For Service

Central Station Information:

Account #: ___________________________________ Telephone #:_________________________________

Installer Information:

Company: ___________________________________ Telephone #:_________________________________

Access Codes

Access codes are used to arm and disarm the system. There are 37 access codes available: 1 master

code, 32 regular access codes, 2 duress codes and 2 supervision codes. Ask your installer for more

information on using the duress and supervision codes.

Only the Master Code can be used to program additional security codes and to change other system

features as well as to arm and disarm the security system. The Master Code will be supplied to you by your

installer. All keypad entries are made by pressing one key at a time.

All access codes can be programmed by following the procedure outlined in “Programming Security

Codes” on page 7.

NOTE: An access code can be a four or six digit number depending on how your installer has

programmed your system. Ask your installer for more information regarding access codes.

Arming the System

Arming from an LED or Fixed Message LCD5501Z keypad:

If the Ready light is ON, the system is ready for arming. If the Ready light is OFF, check to see that all

doors and windows are closed and that motion is stopped in areas covered by motion detectors. The

system cannot be armed unless the Ready light is ON indicating that all zones are closed and the system

is in the Ready state.

Enter your access code. As each digit is entered, the keypad sounder will beep. If the access code was

entered incorrectly, the keypad buzzer will sound steadily for one second. If this occurs, press the [#]

key and re-enter your access code. If the correct access code is entered, the keypad sounder will beep

quickly and the Armed light will come ON. Exit the premises through the door indicated by your installer

as the Exit/Entry door.

The panel will provide an exit delay period, indicated by keypad beeps, for you to exit the premises

without causing an alarm. At the end of the exit delay period, all keypad lights, except the Armed light,

will turn OFF and the system will be armed. You can restart the exit delay once by pressing the Away

button before the exit delay expires. The exit delay time can be changed by your installer.

Arming from an LCD Keypad:

One of the following messages may appear when you attempt to arm your system:

One or more zones are not secured. To secure the system, close all doors and

windows and cease all motion in areas covered by motion detectors.

Use the arrow (< >) keys to verify that the system is clear of troubles and that no zones

are bypassed unintentionally (see “Viewing Trouble Conditions” and “Zone Bypassing”

on page 11).

If you see this message, your installer has set up your system so that it may be armed

with one or more designated zones open. Ask your installer for more details.

The system is in the Ready state and may be fully armed. To arm the system, enter

your access code.

Once the correct access code has been entered, the display will be:

The panel will provide an exit delay period, also indicated by keypad beeps, for you to

exit the premises without causing an alarm. You can restart the exit delay once by

pressing the Away button before the exit delay expires. Exit through the door indicated

by your installer as the Exit/Entry door.

This message will be displayed once the exit delay expires and the system is fully

armed.

If this message appears, be aware of which zones are bypassed and why (see “Zone

Bypassing” on page 10). NOTE: If you arm the system with a zone bypassed or

with a trouble present, your security protection is reduced.

Secure System

Before Arming <>

Enter Code to

Arm System <>

Enter Code to

Arm System

Exit Delay in

Progress

* WARNING *

Bypass Active

Enter Code to

Disarm System

Secure System

or Enter Code

Testing Your System

Alarm Test

The Alarm Test provides two-second tests of the keypad sounder and bell or siren. Begin with the panel

in the Ready state.

From an LED keypad, Enter [

✱][6][Master Code][4] then press [#] to return to the Ready state.

From an LCD keypad, press [

✱] to enter the function list. Use the arrow (< >) keys to scroll to find “User

Functions” and press [✱] to select. Enter your Master Code and scroll to find the following message...

Press [

✱] to perform an Alarm Test. The keypad will display the following message...

Press [#] to return to the Ready state.

Full System Test

We recommend that you test your system weekly. Should the system fail to function properly, call your

installation company immediately for service.

NOTE: Perform system tests during off-peak hours, such as early morning or late evening.

1. Inform the monitoring station that you are testing your system.

2. Begin with the system in the Ready state.

3. Perform a Bell/Battery test by pressing [

✱][6][Master Code][4]. The bell and keypad buzzer will

sound for two seconds and all keypad lights will turn ON. Press [#] to exit.

4. Activate each sensor in turn (e.g. open a door/window or walk in motion detector areas).

From an LED keypad, observe the zone light turn ON when the zone is activated. The zone light will

turn OFF when the system restores to normal (i.e. door or window closed).

From an LCD keypad, the following message will be displayed when each zone is activated...

Use the arrow (< >) keys to view which zone is open. This message will disappear

when the zone is restored.

5. If the panel has any fire zones, activation will cause the alarm signal to sound in a pulsed mode.

CAUTION: Do not use an open flame or burning materials to test a smoke or heat detector.

Contact your installer for information on safe methods of testing detectors.

6. When testing is complete, call and advise the monitoring station. Should the system fail to function

properly, contact your installer.

NOTE: Some features described above will not be functional unless enabled by your installer.

Please ensure that your installer has advised you which features are functional on your system.

Door Chime Feature

The door chime feature is used to provide a tone from the keypad each time a door or window is opened

or closed. Your installer will program which doors and windows will activate the door chime.

To activate the door chime from an LED or Fixed Message LCD5501Z keypad:

Enter [✱][4] to turn the door chime feature ON and OFF. When the command is entered, the keypad

buzzer will beep 3 times if the door chime feature is enabled and will sound one long beep if it is

disabled.

Secure System

Before Arming <>

Select Option <>

System Test

In Progress

To view troubles from an LED or Fixed Message LCD5501Z keypad:

A trouble will be indicated by the Trouble light/message, which will remain ON until the trouble condition

is cleared. If you cannot determine the cause of the trouble condition, contact your installer for assistance.

To view the type of trouble condition, press [✱][2]. One or more zone indicators will turn ON, indicating

the various trouble conditions:

ZONE iNDICATOR TYPE OF TROUBLE

1 ................. Service required. Call your installation company for service.

2 ................. Indicates the loss of AC power. When this trouble occurs, the Trouble light will turn

ON but keypad buzzer will not sound.

3 ................. Telephone line trouble.

4 ................. The panel has failed to communicate with the central station.

5 ................. Zone fault. Press [5], the zone indicator(s) corresponding to the faulted zones will turn ON.

6 ................. Zone tamper. Press [6] and the zone indicator(s) corresponding to the tampered

zones will turn ON.

7 ................. Low zone battery. This trouble is generated when a wireless device exhibits a low

battery condition.

Press [7] one, two, or three times to view which devices are experiencing battery

failure. The following will occur:

Keypad beeps: Keypad displays:

Press [7] 1 Zones with low batteries (LED/Fixed Message LCD keypad -

zone indicators 1 to 32)

Press [7] again 2 Handheld keypads with low batteries (LED/Fixed Message

LCD keypad - zone indicators 1 to 4)

Press [7] again 3 Wireless keys with low batteries (LED keypad - zone

indicators 1 to 8). To view the battery conditions of wireless

keys 9 through 16, you must be at an LCD keypad.

8 ................. Loss of time on system clock. To set the system time, follow the instructions in

“Setting System Date and Time” on page 12.

To view troubles from an LCD Keypad:

From the Ready state, use the arrow (< >) keys to scroll to the following message.

Press [

✱][2] key to view the trouble. The message will read...

Use the arrow (< >) keys to view which troubles are present on the system. Once you

have scrolled through the list of troubles, press the [#] key to exit the Trouble Viewing

mode and return to the Ready state.

Setting the System Date and Time

To set the system time, enter [✱][6] followed by the Master Code. Press [1]. The keypad will now accept

10 consecutive digits:

• Enter the Time in Hours and Minutes using the 24-hr format (00:00 to 23:59).

• Enter the Date in Months, Days and Years (MM DD YY).

NOTE: If you have an LCD keypad, your installer may have programmed your system to display the time

and date while the keypad is idle. If this is the case, you may have to press the [#] key to clear the

date and time before entering an access code to arm the system, or before performing any other

keypad function.

System Trouble

(*2) to View <>

View Trouble <>

“Trouble Message”

Alternate Arming Methods

Away Arming

Arming the system in the Away mode will have all interior zones and perimeter zones active. If motion is

detected in the interior zones, or if one of the perimeter zones is violated, the alarm sequence will begin.

To arm in the Away mode, enter your access code and exit the premises through a designated Exit/

Entry door. The system will recognise that occupants have left the premises. Once the exit delay

expires, the system will be fully armed.

You can restart the exit delay once by pressing the Away button before the exit delay expires.

Audible Exit Fault

In an attempt to reduce false alarms, the Audible Exit Fault will to notify you of an improper exit when

arming the system in the Away mode. If you do not exit the premises during the exit delay period, or if

you do not securely close the Exit/Entry door, the system will notify you that it was improperly armed. It

will do this in two ways: the keypad will emit one continuous beep, and the bell or siren will sound. If

this occurs, you must re-enter the premises, enter your access code to disarm the system, and then

follow the arming procedure again, making sure to exit the premises properly. Your installer will inform

you if the Audible Exit Fault feature has been enabled on your system.

Stay Arming

This feature, if enabled by your installer, will allow you to arm the perimeter zones while leaving the

interior zones inactive so that you can remain on the premises while the system is armed. When you

enter your security code to arm the system, or press the "Stay" button on the keypad, and

do not

exit

the premises through a designated Exit/Entry door, the system will arm in the Stay mode, automatically

bypassing the interior zones.

The interior zones can be reactivated at any time by entering [✱][1] at any keypad. If you reactivate

the interior zones, do not go into areas covered by motion detectors. To access areas protected by

motion sensors, you must enter your security code and disarm the system.

Arming Without Entry Delay

If you wish to arm your system without the entry delay, enter [✱][9] then your access code. The Armed

light will flash as a reminder that the system is armed and has no entry delay. An entry through any

zone programmed as a delay zone will create an instant alarm.

Quick Arm

When the Quick Arm feature is enabled, you may arm the system by simply pressing [✱][0] instead of

your access code. Please note that pressing [✱][0] will only allow you to arm the system; to disarm,

you must enter a valid access code. Your installer will inform you if the Quick Arm feature has been

enabled on your system.

Quick Exit

When the Quick Exit feature is enabled, pressing [✱][0], or the "Exit" button on the keypad, while the

system is armed will provide a two-minute window for you to exit the premises. During this time, you

may only open and close the designated Entry/Exit door once. Once the door is closed, the panel

will end the two-minute quick exit delay. If the door is opened again, or if the door is not closed after

two minutes, or if another delay zone is opened, the panel will begin the entry delay. Your installer will

inform you if the Quick Exit feature has been enabled on your system.

Disarming the System

Disarming from an LED or Fixed Message LCD5501Z keypad:

Enter the premises through a designated Exit/Entry door. Entering by any other door will sound an

immediate alarm. As soon as the Exit/Entry door is opened, the keypad will beep to indicate that the

system should be disarmed. Go to the keypad and enter your access code. If you made an error

entering your code, re-enter the code correctly. As soon as the correct code is entered, the Armed

light will go out and the keypad will stop beeping.

The correct access code must be entered before the entry delay period expires. If a valid access

code is not entered during this time, the system will go into alarm. Your installer can change the entry

time delay.

If an alarm occurred while the system was armed, the Memory light and the zone light corresponding

to the zone that caused the alarm will flash for 30 seconds. After the 30-second period, the Memory

light and zone light will stop flashing and the panel will return to the Ready state. Pressing the [#] key

during the 30 second period will cancel the alarm memory display. To view other alarms, press [✱][3].

If a trouble was detected when the panel is disarmed, the Trouble light will turn ON (See “Viewing

Trouble Conditions” on page 11 to determine the source of the trouble.) Please note that troubles will

not display while the system is in the Alarm Memory Display mode.

Disarming from an LCD Keypad:

Upon entering through a designated Exit/Entry door, the keypad will beep and the entry delay will

commence, reminding you to disarm the system. The keypad will display the following message...

Enter your access code. If an error is made in entering the code, re-enter the

code correctly.

When a valid access code is entered, the keypad will stop

beeping. If there were no alarms while the panel was armed, and there are no

troubles, the display will read...

After about five seconds, the system will return to the Ready state and the display

will read...

If there was an alarm while the system was armed, this message will be displayed.

Use the arrow (< >) keys to view which zones caused the alarm. If a zone is still in

alarm, the display will show the following message to indicate that a zone is open...

Upon disarming and if a trouble is present, this message will be displayed. Use the

arrow (< >) keys to view which troubles are affecting the system (see “Viewing

Trouble Conditions” on page 11).

NOTE: If you return and find that an alarm has occurred while you were away, it is possible that

an intruder may still be on the premises. Go to a neighbour’s house, and call the local police to

investigate.

The alarm memory is cleared each time the panel is armed. Any alarms showing are alarms that

occurred only during the last armed period.

Entry Active

Enter Your Code

Enter Code to

Arm System <>

Secure System

Before Arming <>

Enter Code to

Arm System

View Memory <>

“Zone of Alarm”

System Disarmed

No Alarm Memory

Zone Bypassing

The zone bypassing function is used when access is needed to part of the protected area while the

system is armed. Zones that are temporarily out of service due to damaged wiring or contacts may be

bypassed to allow system arming until repairs can be made.

Bypassed zones will not cause an alarm. Zones cannot be bypassed once the system is armed.

Bypassed zones are automatically cancelled each time the system is disarmed and must be reapplied

before the next arming.

NOTE: For security reasons, your installer may program the system to prevent you from

bypassing certain zones.

Bypassing zones reduces your security protection. If you are bypassing a zone due to damaged

wiring or contacts, please call a service technician immediately so that the problem can be

resolved and your system returned to proper working order.

Make sure that no zones are unintentionally bypassed when arming your system.

To bypass zones from an LED or Fixed Message LCD5501Z keypad:

Start with the system in the Ready state. Enter [✱][1][Zone(s) to be bypassed].

Enter the zone(s) as a 2-digit number from 01 to 32. As each zone is bypassed, the corresponding zone

light will turn ON. If a zone is bypassed by mistake, enter that zone number again; the zone light will turn

OFF, indicating that the zone is not bypassed. Press [#] to return to the Ready state.

To bypass zones from an LCD keypad:

To bypass a zone, the system must be in the Ready state. The display will read...

Press the [✱] key to enter the function menu. The display will read...

Press the [✱] key to enter the zone bypassing mode. The display will read...

Use the arrow (< >) keys to find the zone to be bypassed and press the [✱] key to

select it. The display will read...

“B” will appear on the display to show that the zone is bypassed. To unbypass a

zone, enter the zone number; the “B” will disappear from the display to show that the

zone is no longer bypassed.

This display will be shown if a zone was open when you entered the bypassing

command. The open zone will be represented by “O”. If you bypass the open zone, a

“B” will replace the “O”.

To exit the bypassing mode and return to the Ready state, press the [#] key.

Viewing Trouble Conditions

The control panel continuously monitors a number of possible trouble conditions. If one of these trouble

conditions occur, the keypad will beep twice every 10 seconds until you press any key on the keypad.

NOTE: A TROUBLE condition reduces the security your system is designed to provide. Call your

installing company for service.

Enter Code to

Arm System

Press (*) for <>

Zone Bypass

Zone Search <>

“Zone Name”

Zone Search <>

“Zone Name” B

Zone Search <>

“Zone Name” O

Programming codes from an LCD Keypad:

Master Code

Press the [✱] key to enter the function list. Scroll (< >) to...

Press [5] or [✱]. The display will read...

Enter your current Master Code. The display will read...

“40P” represents the Master Code. Press the [✱] key to indicate that you wish to

program the Master Code. The display will read...

Enter the new Master Code. The Master Code must be four digits long, unless

otherwise indicated by your installer. Enter digits 0 through 9 only. Once the new

code is entered, the keypad will beep 3 times and the display will read...

Press [#] to exit the code programming function.

Be sure to record your new Master Code on the “System Information” page in this booklet.

NOTE: We recommend that the factory default Master Code [1234] not be used.

Additional Access Codes

To erase, add or change a user code, press [✱] to enter the function list. Use the arrow (< >) keys to

scroll to the following message...

Press [

✱]. Display will read...

Enter the Master Code. Display will read...

Use the scroll keys (< >) to find the access code – indicated by “02P” to “32P” –

you wish to add, change or delete. Press the [

✱] key to select the code you wish to

change. The display will read...

To add or change a code, enter the new code. Access codes must be four digits

unless otherwise indicated by your installer. Enter digits 0 through 9 only. To delete

an access code, enter [✱]. Once the 4-digit code or [✱] has been entered, the

keypad sounder will beep 3 times and the display will read...

The “P” means the code has been programmed. If there is no “P” then that code is

deleted. Press [#] to exit the code programming function. The Master code cannot be

erased.

Remember to record your new code(s) on the “System Information” page in this booklet.

Access Code Attributes

Additional programmable attributes, such as zone bypassing capability, can be activated or deactivated

for each access code. For more information regarding access code attributes, please contact your

installer.

Press (*) for <>

Access Codes

Enter Master

Access Code

[*] to Edit <>

User Code 01P

Enter New Code

1234 <>

[*] to Edit <>

User Code 01P

(*) to Edit <>

User Code 40P

Enter Master

Access Code

(*) to Edit <>

User Code 40P

Enter New Code

1234 <>

Press (*) for <>

Access Codes

Continued from page 7 ...

If an Alarm Sounds

Fire Alarm

If your system has been installed with fire detectors and the alarm sounds in a pulsing mode, follow

your emergency evacuation plan immediately (see “Fire Escape Planning” on page 15).

Intrusion Alarm

If an intrusion alarm sounds, indicated by a continuous Bell or Siren, the alarm may be silenced by

entering your access code. If the alarm was unintentional, call local authorities immediately to avoid an

unnecessary response.

You can determine the source of the alarm by following the instructions in the “Disarming” section (see

page 6). Once the source of the alarm has been corrected, the panel can be restored to its original

Armed state.

NOTE: A fire alarm has priority over a burglary type alarm.

Function Keys (Not available on the PC1555RKZ)

The keypads have five function keys – marked Stay, Away, Chime, Reset and Exit – which allow easy

single-button activation of the most commonly used features. If your installer has enabled these keys, you can

execute their programmed function by pressing and holding the corresponding key for two seconds.

For information regarding the operation of the function keys, talk to your alarm installer.

Programming Security Codes

Programming codes from an LED or Fixed Message LCD5501Z keypad:

The Master Code

To program the Master Code, enter [✱][5][current Master Code][40][new Master Code]. The Master

Code must be four digits long, unless otherwise indicated by your installer. Enter digits 0 through 9

only. Press [#] to return to the Ready state.

NOTE: You must program all digits in each access code.

Be sure to record your new Master Code on the “System Information” page in this booklet. NOTE: We

recommend that the factory default or obvious codes such as [1111] or [1234] not be used.

Additional Codes

Up to 32 additional access codes (01 through 32) may be programmed.

To program a new code:

Enter [✱][5][Master Code][code number 01 to 32][new access code]. The code number is a double

digit from 01 to 32. Access codes must be four digits unless otherwise indicated by your installer.

Enter digits 0 through 9 only. Press [#] to return to the Ready state.

If an access code already exists for the code number you have selected, it will be replaced by the new

code. Be sure to record your new code(s) on the “System Information” page in this book.

To erase a code:

Enter [✱][5][Master Code][code number 01 to 32][✱]. Press [#] to return to the Ready state. The

Master code cannot be erased.

Continued on page 10 ...

PC5508Z LED Keypad

Memory Light

Message

Upon disarming, if an alarm has occurred while the

system was armed, the Memory light will turn ON (see

“Disarming the System” on page 6).

Bypass Light / Message

If the Bypass light is ON, one or more zones are

bypassed (see “Zone Bypassing”

on page 11).

Fire Light / Message

If the Fire light is ON, a fire alarm has occurred (see

“Fire Alarm Operation” on page 14).

Program Light / Message

The Program light will flash when you are

programming access codes, or performing other

programming functions. If someone is programming

at another keypad, the Program light will turn ON to

indicate that the system is busy.

The PC5516Z and PC5532Z Keypads

are available for applications with more

than 8 zones. The functions explained in

this manual are the same for all three LED

keypad types.

PC1555RKZ LED Keypad

System Light (PC1555RKZOnly):

If the System light is ON, one or more of these conditions

could be present on the system:

System Busy

System Troubles

(see 'Viewing Trouble Conditions' on page 11).

Alarm Memory

(see 'Disarming the System' on page 6).

Zone Bypassing

(see 'Zone Bypassing'

on page 11).

Programming

The System light will flash when you are

programming access codes, or performing other

programming functions. If someone is programming at

another keypad, the System light will turn ON to indicate that

the system is busy.

NOTE: If you have a PC1555RKZ keypad, the System

light acts as a Trouble, Memory, Programming and

Bypass indicator. Unlike the other keypads, these

conditions will only be represented by the System light.

Please keep this in mind when reading other functions in

this manual.

Emergency Keys (PC1555RKZ)

Press the [F]* key for 2 seconds to send a FIRE

transmission.

Press the [A]* key for 2 seconds to send an AUXILIARY

transmission.

Press the [P]* key for 2 seconds to send a PANIC

transmission.

PC5516Z LED Keypad

PC5532Z LED Keypad

The Liquid Crystal Display (LCD) displays prompts and

system information on two 16 character lines.

If “< >” appears, more information can be accessed by

using the arrow (< >) keys. Press [<] to see the previous

function or item of information. Press [>] to advance the

display to next function or item of information.

Press the keys on the number pad as prompted by the

LCD display to view alarms or troubles, to arm and disarm

the system and to bypass zones.

To exit a function and return to the Ready state, press [#]. To

select a function press [✱].

Display Lights (All Keypads)

Ready Light

If the Ready light is ON, the system is ready for arming.

The system cannot be armed unless the Ready light is

ON (see 'Arming the System' on page 4).

Armed Light

If the Armed light is ON, the system has been armed

successfully.

Trouble or System Light

If the Trouble light is ON, see “Viewing Trouble

Conditions” on page 11.

LCD5500Z Keypad

Emergency Keys

Press both * keys for 2 seconds to send a FIRE

transmission.

Press both * keys for 2 seconds to send an

AUXILIARY transmission.

Press both * keys for 2 seconds to send a PANIC

transmission.

* IMPORTANT NOTE (All Keypads): The Fire,

Auxiliary and Panic keys will NOT function unless

programmed by the installer. If these keys are in

service and the installer has enabled audible

feedback, holding down the key for two seconds

will cause the keypad sounder to beep indicating

that the input has been accepted and transmission

is underway. The [A] and keys are programmed

to be used for non-medical emergencies only in

the United States, as per UL requirements.

IMPORTANT NOTE: Test system weekly

and have any system trouble conditions

corrected by your alarm installer.

LCD5501Z Fixed Message Keypad

DSC Power432 User manual

Brand: DSC

Model: Power432

Category: Fire protection

Type: User manual

Download PDF

report

DSC Power432 User manual

DSC Power432 User manual

Related papers

Other documents