Hitachi CP-X10000 Series User manual

1

Projector

CP-X10000/CP-WX11000/CP-SX12000

User's Manual (detailed) – Operating Guide

Thank you for purchasing this projector.

ŹBefore using this product, please read the "User's Manual -

Safety Guide" and related manuals to ensure the proper use of this product.

After reading them, store them in a safe place for future reference.

WARNING

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

NOTE

Trademark acknowledgment

Various symbols are used in this manual. The meanings of these symbols are

described below.

About this manual

WARNING

CAUTION

This entry warns of a risk of serious personal injury or even

death.

This entry warns of a risk of personal injury or physical damage.

Please refer to the pages written following this symbol.



• Windows

®

is a registered trademark of Microsoft Corporation in the U.S. and/or

other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

• Mac

®

is a registered trademark of Apple Inc.

• DVI is a trademark of Digital Display Working Group.

• HDMI, the HDMI logo and High-Deﬁ nition Multimedia Interface are trademarks

or registered trademarks of HDMI Licensing LLC.

• Trademark PJLink is a trademark applied

for trademark rights in Japan, the United

States of America and other countries and areas.

All other trademarks are the properties of their respective owners.

NOTICE This entry notices of fear of causing trouble.

1

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product

itself to ensure correct usage, to prevent danger to the user and others, and to

prevent property damage. The meanings of these symbols are described below.

It is important that you read these descriptions thoroughly and fully understand

the contents.

Projector

User's Manual - Safety Guide

Typical Symbols

This symbol indicates an additional warning (including cautions). An

illustration is provided to clarify the contents.

This symbol indicates a prohibited action. The contents will be clearly

indicated in an illustration or nearby (the symbol to the left indicates that

disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly

indicated in an illustration or nearby (the symbol to the left indicates that

the power plug should be disconnected from the power outlet).

Thank you for purchasing this projector.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transmission or use of this document or contents is not

permitted without express written authority.

WARNING •

Before using, read these user's manuals of this projector to ensure

correct usage through understanding. After reading, store them in a safe place for

future reference. Incorrect handling of this product could possibly result in personal injury

or physical damage. The manufacturer assumes no responsibility for any damage caused

by mishandling that is beyond normal usage defined in these manuals of this projector.

WARNING

This symbol indicates information that, if ignored, could

possibly result in personal injury or even death due to

incorrect handling.

CAUTION

This symbol indicates information that, if ignored, could

result possibly in personal injury or physical damage

due to incorrect handling.

Read this Safety Guide first.

2

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound,

excessive sound, damaged casing or elements or cables, penetration of

liquids or foreign matter, etc. can cause a fire or electrical shock.

In such case, immediately turn off the power switch and then disconnect the

power plug from the power outlet. After making sure that the smoke or odor

has stopped, contact your dealer. Never attempt to make repairs yourself

because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision

problem.

Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock.

Use special caution in households where children are present.

If liquids or foreign object should enter the projector, immediately turn off the

power switch, disconnect the power plug from the power outlet and contact

your dealer.

• Do not place the projector near water (ex. a bathroom, a beach, etc.).

• Do not expose the projector to rain or moisture. Do not place the projector

outdoors.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc

on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case

or bag together with any thing except the accessories of the projector,

signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of

the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

If the projector is shocked, immediately turn off the power switch, disconnect

the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury,

and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation.

Disconnect the

plug from the

power outlet.

Do not

disassemble.

3

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or

burn. Use special caution in households where children are present.

Do not touch about the lens, air fans and ventilation openings during use or

immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision.

Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no dust),

before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose,

unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal

provided at the building using the correct power cord; otherwise, fire or

electric shock can result.

• Don’t take the core of power cord away.

Safety Precautions (continued)

Surely connect

the ground wire.

4

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass.

The lamp can break with a loud bang, or burn out. When the bulb bursts,

it is possible for shards of glass to fly into the lamp housing, and for gas

containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection

cables.

If you keep using a damaged the power cord or cables, it can cause a fire

or electrical shock. Do not apply too much heat, pressure or tension to the

power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.),

contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

Also, do not place a spread, cover, etc, over them because this could result

in the inadvertent placing of heavy objects on the concealed power cord or

cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the plug

or connector.

• Do not place the cord near the heater.

• Avoid bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The

battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when loading

the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well with

water.

• Obey the local laws on disposing the battery.

Safety Precautions (continued)

5

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or

attach the lens cap.

• Avoid any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling,

and cause an injury or damage. Use special caution in households where

children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or

corrosive gas could result in fire or electrical shock.

• Do not place the projector near a smoky, humid or dusty place (ex.

a smoking space, a kitchen, a beach, etc.). Do not place the projector

outdoors.

• Do not use a humidifier near the projector.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged

by dust or the like, internal temperature rises and could cause malfunction.

The projector may display the message such as “CHECK THE AIR FLOW”

or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged, replace

the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and

other parts. Do not place the projector, the remote control and other parts in

direct sunlight or near a hot object such as heater, etc.

Avoid Magnetism.

Manufacture strongly recommends to avoid any magnetic contact that is not

shielded or protected on or near the projector itself. (ie.,. Magnetic Security

Devices, or other projector accessory that contains magnetic material that has not

been provided by the manufacture etc.) Magnetic objects may cause interruption

of the projector's internal mechanical performance which may interfere with cooling

fans speed or stopping, and may cause the projector to completely shut down

.

6

Safety Precautions (continued)

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the

soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of

liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in

case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

CAUTION

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Ask your dealer to cleaning inside of the projector about every

year.

Accumulations of dust inside the projector cause result in fire or malfunction.

Cleaning inside is more effective if performed before every humid periods

such as rainy season.

• Do not clean inside yourself because it is dangerous.

Disconnect the

plug from the

power outlet.

7

Safety Precautions (continued)

NOTE

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans

have a different lifetime in each. These parts may need to be replaced after a long usage

time.

• This product isn’t designed for continuous use of long time. In the case of continuous use

for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or

repetitious use, the lifetime may be shortened, and these parts may need to be replaced

even if one year has not passed since the beginning of using.

• Any inclining use beyond the adjustment range explained in these user’s manuals may

shorten the lifetimes of the consumables.

Before turning on the power, make the projector cool down adequately.

After turning the projector off, pushing the restart switch or interrupting of the power supply,

make the projector cool down adequately. Operation in a high temperature state of the

projector causes a damage of the electrode and un-lighting of the lamp.

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control

sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on

characteristic of the screen, because the projector uses a liquid crystal display panel. The

display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless

specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output

(setting CRT display or simultaneous display of LCD and CRT).

Please read instruction manual of the notebook for more information.

8

• If the lamp should break (it will make a loud bang when it does), unplug

the power cord from the outlet, and make sure to request a replacement

lamp from your local dealer. Note that shards of glass could damage the

projector’s internals, or cause injury during handling, so please do not try to

clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does), ventilate

the room well, and make sure not to breathe the gas that comes out of the

projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the

power cable is not plugged in, then wait at least 45 minutes for the lamp to

cool sufficiently. Handling the lamp while hot can cause burns, as well as

damaging the lamp.

Lamp

The projector uses a high-pressure mercury glass lamp. The lamp can break with a

loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after

you start using them. In addition, when the bulb bursts, it is possible for shards of

glass to fly into the lamp housing, and for gas containing mercury to escape from the

projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash.

Dispose of in accord with environmental laws.

For lamp recycling, go to www.lamprecycle.org. (in USA)

For product disposal, contact your local government agency or www.eiae.org (in the US)

or www.epsc.ca (in Canada).

For more information, call your dealer.

• Do not open the lamp cover while the projector is suspended from above.

This is dangerous, since if the lamp’s bulb has broken, the shards will

fall out when the cover is opened. In addition, working in high places is

dangerous, so ask your local dealer to have the lamp replaced even if the

bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose screws

could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that

there are electrical problems elsewhere besides the lamp. If this happens,

contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst

during use.

• Using the lamp for long periods of time, could cause it dark, not to light up

or to burst. When the pictures appear dark, or when the color tone is poor,

please replace the lamp as soon as possible. Do not use old (used) lamps;

this is a cause of breakage.

WARNING

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

Disconnect

the plug from

the power

outlet

9

Regulatory Notices

FCC Statement Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC

(Federal Communication Commission) equipment provided that the following conditions

are met. Some cables have to be used with the core set. Use the accessory cable or a

designated-type cable for the connection. For cables that have a core only at one end,

connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of

WARNING in this manual), when a problem occurs with the equipment, first refer to the

“Troubleshooting” section of the “Operating Guide”, and run through the suggested checks.

If this does not resolve the problem contact your dealer or service company. They will tell

you what warranty condition is applied.

2

Contents

About this manual . . . . . . . . . . . 1

Contents . . . . . . . . . . . . . . . . . . 2

Introduction . . . . . . . . . . . . . . . 3

Projector features . . . . . . . . . . . . . . . 3

Important safety instruction (for the

moving) . . . . . . . . . . . . . . . . . . . . . . . 3

Checking the contents of package . . 4

Attaching the lens unit . . . . . . . . . . . . 4

Part names . . . . . . . . . . . . . . . . 5

Projector . . . . . . . . . . . . . . . . . . . . . . 5

Control panel . . . . . . . . . . . . . . . . . . . 6

Indicator lamp . . . . . . . . . . . . . . . . . . 6

Rear panel . . . . . . . . . . . . . . . . . . . . 6

Remote control . . . . . . . . . . . . . . . . . 7

Setting up . . . . . . . . . . . . . . . . . 8

Installation environment . . . . . . . . . . 8

Projection style . . . . . . . . . . . . . . . . . 8

Projection distance . . . . . . . . . . . . . . 9

Placement . . . . . . . . . . . . . . . . . . . . 10

Supplementary anti-theft means . . . 10

Connecting with your devices . . . . . 11

Connecting power supply . . . . . . . . 15

Remote control . . . . . . . . . . . . 16

Putting batteries . . . . . . . . . . . . . . . 16

Transmitting condition . . . . . . . . . . . 17

Changing the frequency of remote

control signal . . . . . . . . . . . . . . . . . . 17

Using the REMOTE ID function . . . 18

Using as a wired remote control . . . 18

Laser pointer . . . . . . . . . . . . . . . . . . 18

Operating . . . . . . . . . . . . . . . . 19

Turning on . . . . . . . . . . . . . . . . . . . . 19

Turning off . . . . . . . . . . . . . . . . . . . . 20

Using the elevator feet . . . . . . . . . . 20

Using the functions for the lens . . . . 21

Displaying and switching the image 22

Selecting an aspect ratio . . . . . . . . . 23

Using the automatic adjustment feature

. . 23

Adjusting the position . . . . . . . . . . . 24

Correcting the keystone distortion

. . . 24

Using the magnify feature . . . . . . . . 25

Temporarily freezing the screen . . . 25

Temporarily blanking the screen . . . 26

Temporarily shutting the screen . . . 26

P by P (Picture by Picture) . . . . . . . 27

Using the menu function . . . . . . . . 28



EASY MENU. . . . . . . . . . . . . . . 29

A

SPECT

, A

UTO KEYSTONE

,

KEYSTONE,

KEYSTONE

,

PICTURE MODE, ECO MODE,

MIRROR, RESET, FILTER TIME, LANGUAGE,

A

DVANCED MENU, EXIT

PICTURE menu . . . . . . . . . . . . 31

B

RIGHTNESS

, C

ONTRAST

, G

AMMA

, C

OLOR TEMP

,

C

OLOR

, T

INT

, S

HARPNESS

, A

CTIVE IRIS

, M

Y MEMORY

IMAGE menu . . . . . . . . . . . . . . 34

A

SPECT

, O

VER SCAN

, V

POSITION

, H

POSITION

,

H

PHASE

, H

SIZE

, A

UTO ADJUST EXECUTE

INPUT menu . . . . . . . . . . . . . . 36

P

ROGRESSIVE

, V

IDEO NR

, 3

D

-

YCS

, C

OLOR

SPACE

, C

OMPONENT

, V

IDEO FORMAT

, D

IGITAL

FOMAT

, D

IGITAL RANGE

, C

OMPUTER IN

, F

RAME

LOCK

, R

ESOLUTION

SETUP menu . . . . . . . . . . . . . . 40

AUTO KEYSTONE, KEYSTONE, KEYSTONE

,

E

CO MODE, MIRROR, MONITOR OUT

SCREEN menu . . . . . . . . . . . . . 42

L

ANGUAGE

, M

ENU POSITION

, B

LANK

, S

TART UP

,

M

yScreen

,

M

yScreen Lock

, M

ESSAGE

, S

OURCE

NAME

,T

EMPLATE

, C.

C

.

OPTION menu . . . . . . . . . . . . . 47

S

OURCE SKIP

, A

UTO SEARCH

, A

UTO KEYSTONE

,

D

IRECT ON, AUTO OFF, SUTTER TIMER LAMP

TIME

, FILTER TIME, MY BUTTON, MY SOURCE,

S

ERVICE

NETWORK menu . . . . . . . . . . . 56

S

ETUP

, P

ROJECTOR NAME

,

MY IMAGE

,

I

NFORMATION

, S

ERVICE

SECURITY menu

. . . . . . . . . . . 61

E

NTER PASSWORD

, S

ECURITY PASSWORD

,

MyScreen

PASSWORD

, P

IN LOCK

, T

RANSITION

DETECTOR

, M

Y TEXT PASSWORD

, M

Y TEXT

DISPLAY

, M

Y TEXT WRITING

Maintenance . . . . . . . . . . . . . . 67

Lamp unit . . . . . . . . . . . . . . . . . . . . 67

Filter unit . . . . . . . . . . . . . . . . . . . . . 69

Internal clock battery . . . . . . . . . . . . 70

Others . . . . . . . . . . . . . . . . . . . . . . . 70

Troubleshooting . . . . . . . . . . . 71

Related messages . . . . . . . . . . . . . 71

Regarding the indicator lamps . . . . 72

Phenomena that may be easily

mistaken for machine defects

. . . . . . 74

Warranty and after-service . . . 77

Speciﬁ cations . . . . . . . . . . . . . 77



3

Introduction

This projector has a capability to project various picture signals onto a screen. This

projector requires only a minimal amount of space for installation and can produce

a large projected image from even a short distance. Moreover, the projector has the

following features to extend its potentiality for broad use.

9 The

HDMI

HDMI port can support various image equipment which have digital

interface to get clearer pictures on a screen.

9

The super bright lamp and high quality optical system can fulﬁ ll the demands

of professional uses.

9

The selectable optional lens units and the super wide range of the lens shift

feature will give much more chances to install the product wherever you

want.

9

The lens shutter can hide your inside operations and will help your

presentation.

9

The wealth of I/O ports is believed to support any business scene.

9

This projector's network supports the PJLink

TM

standard.

9

PJLink

TM

is a uniﬁ ed standard for operating and controlling data projectors.

PJLink

TM

enables central control of projectors manufactured by different

vendors and projectors can be operated by a controller. PJLink

TM

compliant

equipment can be managed and controlled at any time and in any place,

regardless of manufacturer.

For the command of PJLink

TM

, see



User's Manual (Technical)

For speciﬁ cations of PJLink

TM

, see the web site of the Japan Business

Machine and Information System Industries Association.

URL: http://pjlink.jbmia.or.jp

9

The unique Electric Dust Catcher Air ﬁ lter system is expected to prevent

air dust from getting into the projector and offers you less maintenance

frequency.

Projector features

Introduction

Important safety instruction (for moving)

*For details, see the



User's Manual (concise) or Safety Guide.

ŹAlways move the projector

with two or more people. Place your hands in the

dented parts on the bottom of the projector when

carrying the projector.

ŹRemove all the attachments including the power

cord and cables, from the projector when carrying

the projector.

WARNING

Dented parts

4

Introduction

(1) Projector

(2) Lens adapter

(3) Hexagon wrench (for installation of

the optional lens unit)

(4) Power cord

(5) Computer cable

(6) Remote control

with two batteries

(7) User’s manuals (a book and a CD)

(8) Security label

Soon after purchasing this product, check that all the following items are included in

the package. If any items should be missing, tell your dealer immediately.

ŹUse only the lens unit speciﬁ ed by the manufacturer.

ŹLeave both attaching and removing the lens unit to the service personnel your

dealer sent.

ŹRead and keep the user’s manual of the lens unit.

ŹUse special caution not to drop the lens unit or knock it against something.

ŹDo not transport the projector to which the lens unit is attached.

WARNING

Keep the original packing materials for the lens unit, and use

them correctly when transporting or storing the lens unit.

CAUTION

ŹDo not touch the lens surface directly.

Ź Keep the dust protector of the projector, and use it while no lens unit is

attached to the projector.

NOTICE

• This product is supplied without a lens unit so that you can choose

from a range of lenses (



77) that can meet your requirements. Ask your dealer

about details, and prepare one or more lens unit together with this product.

• Some additional accessories or services may be required for your use. We

recommend consult with your dealer beforehand.

NOTE

ŹKeep the original packing materials, and use them correctly

when transporting or storing the product.

CAUTION

Request your dealer to install the lens unit in the projector. Be sure to leave both

removing and attaching the lens unit to the service personnel your dealer sent.

(1)

(2)

(3)

(8)

(4)

(7)

(6)(5)

BLANK LASER

FREEZE

LASER

INDICATOR

DIGITAL

STANDBY/ON COMPUTER

LENS SHIFT

KEYSTONE

ID 3

ID 4

ID 2

ID 1

VIDEO

AUTO

ASPECT

RESET

MENU

MAGNIFY

ON

OFF

3

4

ENTER

FOCUS

+

-

POSITION

PbyP

ZOOM

+

-

1

2

MY BUTTON

MY SOURCE

SHUTTER

Checking the contents of package

Attaching the lens unit

5

Part names

Projector

(1) Dust protector

(2) Remote sensors (x 2) (



17)

(3) Exhaust vents

(4) Filter cover (



69)

The ﬁ lter unit and intake vent are

inside.

(5) Control panel (



6)

(6) Rear panel (



6)

(7) Shutdown switch (



73)

(8) Lamp cover (



67)

The lamp unit is inside.

(9)

AC IN

AC IN (AC inlet) (



15)

(10) Power switch (



19,20)

(11) Security bar (



10)

(12) Security slot (



10)

(13) Dented part (x 2) (



3)

(14) Elevator feet (x 2) (



20)

ŹHOT! : Do not touch around the lamp cover or the exhaust

vents during use or just after use, since it is hot.

ŹDo not look into the lens or vents while the lamp is on, since the strong light is

not good for your eyes.

ŹDo not grab the front cover or front ring to hold the projector, since you can

drop the projector.

ŹDo not handle the elevator feet without holding the projector, since the

projector may drop down.

WARNING

ŹMaintain normal ventilation to prevent the projector from

heating up. Do not cover, block or plug up the vents. Do not place anything that

can stick or be sucked to the vents, around the intake vents. Clean the air ﬁ lter

periodically.

CAUTION

(2)

(3)

(8)

(10)

(9)

(12)

(14)

(4)

HOT!

(7)

(6)

(5)

(13)

(11)

(1)

HOT!

See the NOTICE

ŹDo not touch the lens surface directly.

Ź Keep the dust protector of the projector, and use it when no lens unit is

attached to the projector.

NOTICE

Front ring

Front cover

6

Part names

STANDBY/ON

MENU

LENS SHIFT

COMPUTER

ZOOM

VIDEO

FOCUS

DIGITAL

SHUTTER

I O

HDMI DVI-D

CONTROL IN CONTROL OUT

REMOTE

CONTROL

IN

OUT

S-VIDEO

COMPUTER IN2

COMPUTER IN1

VIDEO 1

BNC

R/Cr/Pr G/Y B/Cb/Pb H V VIDEO 2

Y

Cb/Pb

Cr/Pr

AC IN

LAN

MONITOR

OUT

Control panel

(1)

STANDBY/ON

STANDBY/ON button (



19,20)

(2) Cursor buttons ( Ÿ/ź/Ż/Ź ) (



28)

(3)

MENU

MENU button (



28)

(4)

COMPUTER

COMPUTER button (



22)

(5)

VIDEO

VIDEO button (



22)

(6)

DIGITAL

DIGITAL button (



22)

(7)

LENS SHIFT

LENS SHIFT button (



21)

(8)

ZOOM

ZOOM button (



21)

(9)

FOCUS

FOCUS button (



21)

(10)

SHUTTER

SHUTTER button (



26)

Rear panel(



10)

(1)

HDMI

HDMI port

(2)

DVI-D

DVI-D port

(3)

LAN

LAN port

(4)

MONITOR OUT

MONITOR OUT port

(5)

CONTROL IN

CONTROL IN port

(6)

CONTROL OUT

CONTROL OUT port

(7)

REMOTE CONTROL IN

REMOTE CONTROL IN port

(8)

REMOTE CONTROL OUT

REMOTE CONTROL OUT port

(9)

S-VIDEO

S-VIDEO port

(10)

VIDEO 1

VIDEO 1 port

(11)

VIDEO 2

VIDEO 2 port

(12)

COMPUTER IN1

COMPUTER IN1 port

(13)

COMPUTER IN2

COMPUTER IN2 port

(14)

BNC (G/Y, B/Cb

/Pb

,R/Cr

, R/Cr

/Pr

,H,V)

, H, V) ports

(15) Component

(Y, Cb

/Pb

,Cr

, Cr

/Pr

)

) ports

(6)

(5)

(4)

(1)

(2)

(3)

ŹUse the shutdown switch only when the projector is not turned

off following the normal procedure, since pushing this switch stops operation of

the projector without cooling it down.

CAUTION

(1)

Indicator lamp (



72)

(1)

POWER

POWER indicator

(2)

TEMP

TEMP indicator

(3)

LAMP

LAMP indicator

(4)

SECURITY

SECURITY indicator

(5)

SHUTTER

SHUTTER indicator

SHUTTERPOWER TEMP LAMP SECURITY

(9)

(8)

(7)

(10)

(1) (2) (3) (4) (5)

(2) (4)

(8)(7)(6)(5)

(3) (9)(10)(11)

(13)(12)(14)(15)

The indicator

will light in

green while

the menu of

the function is

displayed.

The

indicator of

group the

selected

input port

belongs to

will light in

green.

The indicator will blink in yellow

while the lens shutter is closed.

7

Part names

Remote control

(1) Laser pointer (



18)

It is a beam outlet.

(2)

LASER INDICATOR

LASER INDICATOR (



18)

(3)

LASER

LASER button (



18)

(4)

STANDBY/ON

STANDBY/ON button (



19,20)

(5)

ID

ID (

1-4

1-4) button (



18)

(6)

COMPUTER

COMPUTER button (



22)

(7)

VIDEO

VIDEO button (



22)

(8)

DIGITAL

DIGITAL button (



22)

(9)

MY SOURCE

MY SOURCE button (



22)

(10)

LENS SHIFT

LENS SHIFT button (



21)

(11)

ZOOM +/-

ZOOM +/- button (



21)

(12)

FOCUS +/-

FOCUS +/- button (



21)

(13)

AUTO

AUTO button (



23)

(14)

POSITION

POSITION button (



24)

(15)

ASPECT

ASPECT button (



23)

(16)

KEYSTONE

KEYSTONE button (



24)

(17)

MAGNIFY ON/OFF

MAGNIFY ON/OFF button (



25)

(18)

FREEZE

FREEZE button (



25)

(19)

BLANK

BLANK button (



26)

(20)

SHUTTER

SHUTTER button (



26)

(21)

MY BUTTON

MY BUTTON (

1-4

1-4) button (



49)

(22)

PbyP

P by P button (



27)

(23)

MENU

MENU button (



28)

(24)

ENTER

ENTER button : press the center point.

Cursor button: press the point Ÿ/ź/Ż/Ź (



28).

(25)

RESET

RESET button (



28)

(26) Wired remote control port (



18)

(27) Battery cover (



16)

(28) Battery holder (



16)

(29) Frequency switch (



17)

ŹDo not look into the beam outlet or

point the beam at people or pets while pressing the

LASER

LASER button, since the beam is not good for eyes.

WARNING

ŹNote that the laser beam may result

in hazardous radiation exposure. Use the laser pointer

only for pointing on the screen.

CAUTION

BLANK LASER

FREEZE

LASER

INDICATOR

DIGITAL

STANDBY/ON COMPUTER

LENS SHIFT

KEYSTONE

ID 3

ID 4

ID 2

ID 1

VIDEO

AUTO

ASPECT

RESET

MENU

MAGNIFY

ON

OFF

3

4

ENTER

FOCUS

+

-

POSITION

PbyP

ZOOM

+

-

1

2

MY BUTTON

MY SOURCE

SHUTTER

(4)

(2)

(1)

(3)

Back of

the remote control

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

8

Setting up

Read this chapter through ﬁ rst. Then install the projector into place.

ŹDo not place the product on an unstable surface such as an

uneven, tilted, or vibrating place.

ŹDo not place the product near water - for example, near a bathtub, washbowl,

kitchen sink, or laundry tub; in a wet basement, near a swimming pool, beach; or

outdoors.

WARNING

ŹDo not place the product in a dusty, smoky, or humid place -

for example, on a passage, in a smoking space, in a kitchen, or outdoors.

ŹDo not place the product near heat sources - for example, radiators, heat

registers, stoves, or other product (including ampliﬁ ers) that produces heat.

ŹDo not place this product in a magnetic ﬁ eld.

CAUTION

Installation environment

This product requires an installing place that is stable, cool and airy. Check your

installation environment in accordance with the following.

ŹDo not place the product in a place where radio interference may

be caused.

Ź Do not place the projector in a place where any strong lights hit the remote

sensors.

NOTICE

Projection style

This projector can be used by the following projection styles. Choose the style

suitable to your use.

(1) Standard style

(placed on a table)

(2) Ceiling mount

(suspended from a ceiling)

• In the case of ceiling mount, upward projection, or downward

projection, the speciﬁ ed mounting accessories (



77) and service are required

to install the projector. Request them from your dealer. Ask your dealer for

installation other than styles above.

NOTE

ŹConsult with your dealer about installation beforehand.

ŹUse only the mounting accessories the manufacturer speciﬁ ed, and leave

installing and removing the projector with the mounting accessories to the

service personnel.

WARNING

9

Setting up

Projection distance

Refer to the following to arrange the projector and your screen. The values shown in the

following table were calculated for the model CP-X10000 with the standard lens unit SD-

804. See the user’s manual of your lens unit for your case. The values differ for every

combination of the projector and the lens unit.

(a) Screen

size

[inch (m)]

4 : 3 screen 16 : 9 screen

(b) Projection distance

[m (inch)]

(c) Screen height

[cm (inch)]

(b) Projection distance

[m (inch)]

(c) Screen height

[cm (inch)]

min. max. down up min. max. down up

40 (1.0) 1.7 (66) 2.3 (89)

-23 (-9)

84 (33)

1.3 (53) 1.8 (72)

-33 (-13) 83 (33)

60 (1.5) 2.6 (103) 3.5 (136)

-34 (-13) 125 (49)

2.1 (83) 2.8 (110) -49 (-19) 124 (49)

70 (1.8) 3.1 (121) 4.0 (159)

-40 (-16)

146 (58) 2.5 (98) 3.3 (129) -58 (-23) 145 (57)

80 (2.0) 3.5 (139) 4.6 (183)

-45 (-18)

167 (66) 2.9 (112) 3.8 (148) -66 (-26) 165 (65)

90 (2.3) 4.0 (157) 5.2 (206)

-51 (-20)

188 (74) 3.2 (127) 4.3 (168) -74 (-29) 186 (73)

100 (2.5) 4.4 (175 5.8 (230)

-56 (-22)

209 (82) 3.6 (142) 4.7 (187) -82 (-32) 207 (81)

120 (3.0) 5.4 (211 7.0 (277)

-68 (-27)

251 (99) 4.4 (172) 5.7 (225) -99 (-39) 248 (98)

150 (3.8) 6.7 (266 8.8 (347)

-85 (-33)

313 (123) 5.5 (216) 7.2 (283) -123 (-49) 310 (122)

200 (5.1) 9.0 (356 11.8 (464)

-113 (-44)

418 (164) 7.4 (290) 9.6 (379) -164 (-65) 414 (163)

250 (6.4) 11.3 (447 14.8 (582)

-141 (-56)

522 (206) 9.2 (364) 12.0 (474) -206 (-81) 517 (204)

300 (7.6) 13.6 (537 17.8 (699)

-169 (-67)

627 (247) 11.1 (438) 14.5 (570) -247 (-97) 620 (244)

350 (8.9) 15.9 (628 20.7 (816)

-198 (-78)

731

(288) 13.0 (512) 16.9 (666)

-288 (-113) 724 (285)

400 (10.2) 18.2 (718 23.7 (934)

-226 (-89)

835 (329) 14.9 (586) 19.4 (762) -329 (-130) 827 (326)

500 (12.7) 22.8 (899 29.7 (1168)

-282 (-111)

1044 (411) 18.6 (734) 24.2 (954) -411 (-162) 1034 (407)

600 (15.2) 27.4 (1081 35.6 (1403)

-339 (-133)

1253

(493)

22.4 (882) 29.1 (1145) -493 (-194) 1241 (488)

700 (17.8) 32.0 (1262 41.6 (1638)

-395 (-156)

1462 (576) 26.2 (1030) 34.0 (1337) -576 (-227) 1447 (570)

(a)

(b)

(c) up

(c) down

* The values shown in the table are calculated for a full size screen: 1024×768

(a) Screen size (diagonal)

(b) Projection distance (±10%)

(c) Screen height (±10%), when the vertical lens shift is set full upward.

Projector top

Projector bottom

(Installation side)

ŹDo not use a polarized screen, since it can cause a red image. NOTICE

10

Setting up

Supplementary anti-theft means

This projector has the security bar for a commercial

anti-theft chain or wire up to 10 mm in diameter, and

also the security slot for the Kensington lock.

For details, see the manual of your security tool.

ŹDo not use the security slot to

prevent the projector from falling down, since it is not

designed for it.

WARNING

•

These are not provided as comprehensive theft

preventions but supplemental measures.

NOTE

Security slot

Anti-theft chain or wire

Security bar

ŹKeep the projector away from anything that is easy to catch

ﬁ re.

ŹDo not block or cover the openings on the projector, and keep sufﬁ ciently

space for ventilation around the projector.

• Do not use the projector on a cushiony surface such a rug, a carpet or bedding.

• Keep the projector away from any light materials such as a piece of paper that

can stick to the intake holes.

ŹDo not use the projector on an unstable stand such as a cart.

ŹPlace the projector so that nothing enters to the inside of the projector.

• Keep the projector away from any small things such as paperclips that can fall

into the inside.

• Keep the projector away from any liquids that can spill or leak into the product.

WARNING

ŹKeep the projector away from anything that is heat conductive

such as metal.

• Do not use the projector on a metallic table.

ŹKeep the projector away from anything that is weak in heat such as some kinds

of plastics.

CAUTION

ŹPlace the projector so that there is nothing that blocks the

projection light to the screen.

Ź Avoid exposing directly the remote sensor to any strong lights.

NOTICE

Placement

ŹDo not place the anti-theft chain

or wire near the projector’s exhaust vents, since the

chain or wire heated by the hot exhaust gas may

cause burns.

CAUTION

In placing the projector in place in accordance with the preceding section

"Projection distance" (



9) heed the following too.

11

Setting up

Connecting with your devices

Before connecting the projector to your devices, check the manual of the device in

order to make sure that the device is suitable to connect with this projector and to

check what is required for the connection.

Consult your dealer when the required accessory did not come with the product or

the accessory is damaged. It may be regulated under some standard.

ŹUse only the accessories speciﬁ ed or recommended by

manufacturer. Modify neither a projector nor accessories.

ŹDo not connect or disconnect the projector with devices while they are

connected to a power supply except for the cases directed by the manuals of

devices.

WARNING

ŹSome connecting cable may have to have a speciﬁ c length,

or a ferrite core at the end to connect to the projector, under the regulation of

electro-magnetic interference. When a ferrite core is attached to the speciﬁ ed

cable only at one end, connect to the projector the end that the ferrite core is

attached at.

ŹBe careful not to set a connector into a wrong port or with a wrong way.

ŹBe careful not to damage the cables. Route the cables not to be stepped on

and pinched out.

CAUTION

(continued on next page)

• For this product, the optional cable cover is ready to be purchased. To

place an order for it, please tell your dealer the type name of it (



77).

NOTE

After making sure that the projector and the devices are turned off, perform

the connection, according to the following instructions. Refer to the ﬁ gures in

subsequent pages.

ŹDo not turn your device on prior to the projector, except for the

cases directed by the manuals of devices.

NOTICE

Page is loading ...

Hitachi CP-X10000 Series, CP-SX12000, CP-WX11000, CP-WX11000W User manual

Related papers

Other documents