KYE Systems Corp EASY PEN i405 User manual

Brand: KYE Systems Corp

Model: EASY PEN i405

Type: User manual

This manual is also suitable for

ENGLISH

ENIUS

RAPHIC

ABLET

Q U I C K I N S TA L L AT I O N G U I D E

CAUTION: PLEASE

INSERT

THE

DRIVER

INTO

YOUR

COMPUTER

FIRST

AND

THEN

THE

INSTRUCTIONS

COMPLETE

YOUR

SETUP

PROCESS.

INTRODUCTION

DRIVER INSTALLATION

Windows:

1. Insert the driver disc into your computer’s CD-ROM drive. When prompted, select “Driver Setup”, and press OK to

install driver.

Note: In most systems, the Setup Wizard will start automatically. If Automatic Setup does not begin, start the Setup

program manually by selecting “Start/Run”, type "E:\setup", where “E:” represents the location of the CD-ROM

drive, then press “Enter”.

Note: In certain cases, Windows might ask for your permission because it cannot recognize the driver you are

downloading. If this occurs, select “Continue Anyway” and continue to install.

2. Please insert the driver CD into your computer first and then follow the instructions to complete your setup process.

Macintosh:

1. Insert the driver disc into your computer’s CD-ROM drive.

2. Check to see if the “Genius Tablet” is shown on the screen. Double click the icon then follow the instruction.

3. Enter your administrator name and password to process the next step till it’s finished.

Note: For more information, refer to the MAC user manual on the driver disc.

CAUTION: ONCE

THE

INSTALLATION

HAS

BEEN

COMPLETED,

REBOOT

YOUR

MACINTOSH

BEFORE

PLUGGING

THE

DEVICE

INTO

YOUR

COMPUTER.

HARDWARE INSTALLATION

CAUTION:

MAKE

SURE

THAT

YOU

HAVE

INSTALLED

THE

DRIVER

SOFTWARE

(SEE

ABOVE)

INTO

YOUR

COMPUTER

BEFORE

INSTALLING

THE

HARDWARE.

1. Plug the Graphic Tablet USB cable into your computer’s

USB port (located on the computer, display, or keyboard).

The Graphic Tablet’s LED light will indicate the operational

status, and your computer screen will display a “found new

hardware” message.

1. Working area

2. Button 2

3. Button 1

4. Pen tip

ENGLISH

Figure 1 Tablet Plate components

VERIFYING THE INSTALLATION

To ensure that everything has been installed properly, please follow the procedures below. Check the User’s manual on

the CD-ROM for more information.

ERIFYING

ARDWARE AND

RIVER

UNCTIONS

The LED light on the Tablet Plate is the main indicator for hardware

operation. The light normally stays off, and will come on and off in response to

various conditions. Watch the status of the Tablet Plate LED light as you go

through these steps. None of the tests, except the last two, require the tablet

driver to be installed.

For the cordless pen (stylus) or the wireless mouse , tap on any surface or

press the left button of the mouse to “wake it up”, in case the pen or the

mouse has gone to "sleep" after it is not used for a few minutes.

As soon as the Tablet Plate receives power, the LED light will come on briefly, and will normally stay off.

When the working area (Plate) detects the presence of the pen, the LED light will flash slowly. This

happens when the pen tip is directly above the working area of the tablet plate and is low enough.

When you press a button on the body of the pen or the mouse, the LED light will come on.

When you press the pen tip against the tablet plate anywhere in the working area, the light will also come on.

If the tablet driver has been properly installed, a small tablet icon ( ) will appear in system Task Bar area,

normally at the lower right corner of the screen.

With the tablet driver properly installed, moving the pen tip or the mouse over the working area will cause

the cursor on the screen to move accordingly.

TO CHANGE THE PEN TIP

1. Place the Pen tip into the tip remover.

2. Simply pull the Pen up, and then insert a new tip.

Note: Pliers (not included in package) may also be used to remove the pen tip.

To replace the Tablet Pen battery:

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment. (15.21)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.(15.19(a)(3))

(1) Twist the pen cap.

(2) Pull the pen cap to open it.

(3) Put one AAA battery into the pen.

(4) Twist the pen cap back on the pen.

KYE Systems Corp EASY PEN i405 User manual

Brand: KYE Systems Corp

Model: EASY PEN i405

Type: User manual

This manual is also suitable for

Download PDF

report

KYE Systems Corp EASY PEN i405 User manual

This manual is also suitable for

KYE Systems Corp EASY PEN i405 User manual

Related papers

Other documents