www.ebodeelectronics.eu
User Manual
VLHD38
User guide 3
Bedienungsanleitung 14
Gebruikershandleiding 25
Användarmanual 36
Guide utilisateur 47
Guía del usuario 58
Manual do utilizador 69
Manuale per l’utente 80
Before using this ebode product, please read this manual carefully!
2-6-2016 2 ebode VLHD38
CONTENTS OF THE KIT
When unpacking your ebode HD60GH please check if the items below are included, if
any items are missed or damaged, please contact your distributor or dealer.
Wireless HD Transmitter
Wireless HD Receiver
5V/2a Power Supply x2
USB Power Cable x2
HDMI Cable x2
IR Emitter Cable
USB Cable
User Manual
TECHNICAL SPECIFICATION
Model: ebode electronics VLHD38
Supported Resolution: 1080P, 1080I, 720P
Support HDMI1.4A video/audio format and encrypted video format.
HDCP2.0Transmission Distance: 200ft/60m line of sight
System Latency: <100ms
Antenna: Omni directional built-in antenna
Power: 100~ 240V alternating input current, 5V/3A DC output power adaptor
Certificates: FCC、CE
Working temperature: 0℃ - 50℃
Dimension: 146(L)*93(W)*25(H)mm
PRODUCT CHARACTERISTICS
Products In Colli: 20 PCS
Weight Colli: 21,7 KG
Volume Colli: 0.098 CBM
Length Colli: 62,0 cm
Width Colli: 52,0 cm
Height Colli: 30,5 cm
Length Product Carton: 29,0 cm
Width Product Carton: 7,5 cm
Height Product Carton: 15,5 cm
Weight Article: 1,000 KG
Transmitter Dimensions: 9,0*2,5*14,5 cm
Transmitter Weight: 0,125 KG
Receiver Dimensions: 9,0*2,5*14,5 cm
Receiver Weight: 0,125 KG
EAN Code EU: 8717399103374
EAN Code UK: 8717399103381
2-6-2016 3 ebode VLHD38
User Guide
Please visit
www.ebodeelectronics.eu for our latest manual!
Contents
1. CONFORMITY OF USE
2. INTRODUCTION
3. MAIN FEATURES
4. FUNCTIONS
5. FREQUENTLY ASKED QUESTIONS
6. SAMPLE OF USE
1. Conformity of Use
For carefree and safe use of this product, please read this manual and safety information
carefully and follow the instructions. The unit is registered as a device that does not
cause or suffer from radio-frequency interference. It is CE approved and it conforms with
the Low Voltage Directory. The safety and installation instructions must be observed.
Technical manipulation of the product, or any changes to the product, is forbidden, due
to security and approval issues. Please take care to set up the device correctly - consult
your user guide. Young children should use the device only under adult supervision. No
guarantee or liability will be accepted for any damage caused due to incorrect use of the
equipment supplied, other than indicated in this owner’s manual.
1.1 Safety Warnings
To prevent short circuits, this product (except if specified for outdoor usage) should
only be used inside and only in dry spaces. Do not expose the components to rain or
humidity.
Only connect the adapter to the mains after checking whether the mains voltage is the
same as the values on the rating labels. Never connect an adapter or power cord when it
is damaged. In that case, contact your supplier. If there is any danger of a
thunderstorm, it is a good precaution to unplug the power supply from the mains
network in order to protect it from lightning. The same applies if the system is to be out
of action for any length of time.
Avoid strong mechanical tear and wear, extreme ambient temperatures, strong
vibrations and atmospheric humidity.
Do not disassemble any part of the product: the device contains live parts and no user-
serviceable parts are inside. The product should only be repaired or serviced by qualified
and authorized service personnel. Defected pieces must be replaced by original (spare)
parts.
In case of improper usage or if you have opened, altered and repaired the product
yourself, all guarantees expire. The supplier does not accept responsibility in the case of
improper usage of the product or when the product is used for purposes other than
specified. The supplier does not accept responsibility for additional damage other than
covered by the legal product responsibility.
1.2 Important Information
Before you use the transmitter and receiver, it is important that you read this user
manual to get important information and instructions regarding wireless HD transmitter
and receiver.
2-6-2016 4 ebode VLHD38
Thank you for purchasing this quality product. Any defects in components or faulty
workmanship occurring within a specific period will be rectified or repaired free of
charge, but this warranty may not apply to the following cases:
Unauthorized modifications to the products or repair by an unauthorized technician.
Breakage caused by accidents including but not limited to fire, water immersion, and
moisture.
Use on incorrect voltage, use contrary to operating instructions.
Product model number got altered, removed or made illegible.
1.3 Safety Precautions
Power must be switched off when not in use, any power adaptors connected AV
devices and TV should be plugged out.
Power outlet: To prevent electricity shock, please check if the mains lead used on the
receiver and transmitter corresponds to the power outlet.
Mains lead: stepping or putting heavy stuffs on mains lead is prohibited.
Power overloading: Do not overload the power outlets or extend the length of power
line, otherwise electric shock or fire could happen.
Lighting stroke: disconnect the power adaptor when product is not used for a long
time or in lighting stroke weather.
Switch off the power when product is not in use to prevent electric shock or fire.
1.4 Warning
Keep the product away from objects with liquids and splashing or dripping on this
product is strictly prohibited.
Put the product in a well-ventilated space and keep it away from direct sunlight or
any source of heat.
Do not expose the product to rain or moisture, otherwise electric shock or fire could
happen.
2-6-2016 5 ebode VLHD38
1.5 FCC ID Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: 1) this device may not cause harmful interference. 2) this device must
accept any interference received, including interference that may cause undesired
operation.
The user manual or instruction manual for an intentional or unintentional radiator shall
caution the user that changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment. In
cases where the manual is provided only in a form other than paper, such as on a
computer disk or over the Internet, the information required by this section may be
included in the manual in that alternative form, provided the user can reasonably be
expected to have the capability to access information in that form.
For a Class B digital device or peripheral, the instructions furnished the user shall include
the following or similar statement, placed in a prominent location in the manual text:
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
1.6 IC ID Warning
Disclaimer: Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including
interference that may cause undesired.
1.7 Trademark Information
HDMI, HDMI Logo and High Definition Multimedia Interface are registered trademarks of
HDMI Licensing LLC in America and other countries.
1.8 Special Notice:
Do not use this product nearby an aircraft or medical facility to prevent interference.
Please handle this device carefully otherwise wireless wave may cause the abnormal
video and audio (noise, blocked image…etc.,)
1. Put it on the desk steadily; don’t try to move it when connected.
2. Keep it away from refrigerator or other metal furniture.
3. Do not place it in narrow place.
Do not place this product in a dusty, humid environment, and also in the place where
the temperature is out of the stated operational temperature range.
This product is with DC power supply. Please make sure that the replacing power
adapter with identification of 5V/3A to avoid irreparable fault.
2-6-2016 6 ebode VLHD38
Do not cover it or place other heavy objects on top of the unit which may block
thermal ventilation. Good air circulation around the product is required.
For energy saving, please turn off the power switch or unplug the power adapter
when the units are not in use.
If the product does not work properly, please restart it. If the problem maintains, cut
off the power and send it to professional technicians for repair or disposal. Please do
not open or repair it yourself.
This product has been manufactured and tested to comply with each country’s safety
regulations. However, it doesn’t guarantee that interference would never happen in
some specific environment. If interference does occur, please take away the
interfering objects from transmitter and receiver.
The optimal working distance between transmitter and receiver is 1 meter to 30
meters.
1.9 Cleaning
Unplug power adaptor before performing any cleaning. To clean the device, wipe with a
soft, dry cloth or with a cloth moistened with alcohol.
Do not demount the device when connected to power outlet, otherwise, electricity
shock may happen.
Maintenance should be conducted by an authorized technician.
Dripping or splashing on the device is strictly prohibited.
Keep the device away from fire or any source of heat.
Don’t let kids play with this device.
2. Introduction
Forget pulling wires! Long Range Wireless HDMI has arrived. The ebode VLHD38 replaces
your current HDMI cable. The system, consisting of a transmitter and a receiver,
wirelessly streams uncompressed High-Definition videos from any HD video source
device to your HD TV (or projector), placed anywhere in your home. The operating range
is up to 200ft/60m line of sight. Includes USB Power cable which enables you to power
the receiver from a USB port* of your HDTV.
(* The USB port must have at least 1.5 amp. power output.)
3. Main Features
Working on the 5.8GHz Frequency (high-speed band)
HDMI Loop-Through
Built-in Omni antenna
With a transmission distance of 200ft/60m LOS
with less than 100ms latency
Power via USB or adapter
Please note: The VLHD38 cannot start-up a source device from standby over infrared if
the connection is not established. Connection can only be established once the source on
the remote location is powered to establish the HDMI handshake with the Transmitter.
You need to turn on the source (DVD, etc.) manually, which is linked to the VLHD38 to
get the infrared function to work. The main reason this slightly inconvenient handling is
required, is because there is a power-saving feature built in. Without this power-saving
feature the VLHD38 would 24/7 require a connection and therefore draws power and will
add additional cost to the home owner.
2-6-2016 7 ebode VLHD38
4. Functions
4.1 Transmitter Functions
Pre posed LED
Power LED: Indicates if the system is powered.
Video LED: Indicates video output status
Link LED: Indicates device connection status
USB interface: To connect PC or other source equipment.
Postposition LED
Power Button: To turn on or turn off the system
Power interface (DC IN JACK): To connect power adaptor or USB power cable.
Infrared interface (IR slot): To connect the IR emitter.
HDMI In: To connect HD source equipment.
HDMI Out Interface: To connect monitor/TV/screen (loop trough).
Pair Button: Manual pair with the transmitter/receiver.
4.2 Receiver Functions
Pre posed LED
2-6-2016 8 ebode VLHD38
Power LED: Indicates if the system is powered
video LED: Indicates video receiving status
Link LED: Indicates device connection status
USB interface: To connect compatible USB mouse, keyboard or PS3.
Postposition LED
Power Button: To turn on or turn off system
power input interface(DC IN Jack): To connect power adaptor or USB power cable.
HDMI Out: To connect monitor/TV/screen.
Pair interface: To pair with the transmitter/receiver.
4.3 Indicating LED
Working status
Transmitter
Receiver
Power
Video
Lin
k
Power
Vide
o
Link
Normal status
●
●
●
●
●
Add device
●
■
★
●
●
Transmitter: When power, video and link are lit, the device is in operating mode and a
connection is established.
Receiver: When power and link are lit, the device is in operating mode and a connection
is established. Connect a screen/monitor and power on to the correct input to receive
image from the source connected to the Transmitter.
Lit
▪ Not lit
★ Flashing
2-6-2016 9 ebode VLHD38
4.4 Transmitter Connection (Source Location)
1. Please connect the VLHD38 Transmitter Power via the included Power adapter or the
included USB power cable** before you make the below connection.
(** Please note that when using power from USB the USB port needs to deliver a
minimum of 1.5A. If the USB port has less than 1.5A you could damage the USB port or
a connection could not be established)
2. The VLHD38 Transmitter can also send IR from the VLHD38 Receiver (remote
location) back to the Source to control it. Please go to step 3. if you don’t need IR
control from the remote location.
Plug the IR extender into IR OUT and place the IR Emitter on the IR Receiver window of
your source.
HINT: If you can’t find the IR Receiver window on your source, use a flashlight or the
Flashlight of your mobile phone to find the IR Receiver window.
2-6-2016 10 ebode VLHD38
3. Connect the included HDMI cable from the Transmitter HDMI IN port to your source
equipment, such as Blu-Ray DVD, multi-media player, set top box etc. and make sure
they are properly connected.
4. Connect the included HDMI cable from Transmitter HDMI OUT to your display device,
TV, Screen or Projector and make sure they are properly connected.
VLHD38 Loop-Trough (HDMI OUT) explained:
The VLHD38 Transmitter HDMI out port will be used to loop-through your Source HDMI
signal to your screen/monitor (if present). With the loop-trough function you can keep
both the screen/monitor and VLHD38 connected at all time and also watch your source
at the Transmitter side, even when the VLHD38 is not in use on the remote location.
5. USB A-A (Optional): The VLHD38 is capable of sending USB along with the HDMI
Signal. This feature is used with Game Consoles and/or PC systems for keyboards,
mouse and joysticks/game controllers.
Connect the VLHD38 Transmitter and devices, like Blu-Ray DVD, multi-media player, set
top box with USB cable. HINT: if the USB is not working, disconnect USB and establish a
video connection first. After the video is transmitted and received correctly, re-connect
the USB cables.
2-6-2016 11 ebode VLHD38
Warning: Do not connect USB HUBS as these are not compatible with the VLHD38.
Never connect the USB A-A Cable to USB in/out ports of Source Equipment like DVD,
Blu-Ray, Satellite Tuners etc. as this can damage both units.
4.5 Receiver Connection (Remote Location)
1. Please connect the VLHD38 Receiver Power via the included Power adapter or the
included USB power cable** before you make the below connection.
(** Please note that when using power from USB the USB port needs to deliver a
minimum of 1.5A. If the USB port has less than 1.5A you could damage the USB port or
a connection could not be established)
2. Connect the VLHD38 Receiver with the included HDMI cable to your Remote screen
and make sure they are perfectly connected.
2-6-2016 12 ebode VLHD38
USB Optional: Connect a compatible USB mouse, keyboard, gamepad to the receiver
through USB interface and make sure they are perfectly connected. HINT: if the USB
device is not working, disconnect the USB device and establish a video connection first.
After the video connection is successful established, re-connect the USB cables.
4.6 Pair devices:
The VLHD38 should automatically connect when:
Both the VLHD38 Transmitter`s Power Buttons are ON
The source is connected, powered and playing / showing image
The TV on both Transmitter and Receiver side are Powered, ON and set to the right
input channel for HDMI (depends on where the VLHD38 is connected)
All cables are connected properly
30 seconds have been passed (the VLHD38 needs to boot)
If USB Power has been used; has enough output power (minimum 1.5A)
If the VLHD38 connection fails:
Press the PAIR button on the VLHD38 Transmitter
Press the PAIR button on the VLHD38 Receiver
After pairing, the connection is re-established and the system is ready to transport AV
signal. The Receiver TV will show its status (connecting, searching etc.)
In case you have no signal we suggest you to check chapter 5 (Frequently asked
questions) and to find out what has gone wrong.
5. Frequently Asked Questions
Before following the frequently asked questions below, make sure that your receiver and
attached equipment (HD source and display) are all properly connected, switched on and
not in Standby Mode, please give them a 10 second power off reset before taking the
next steps:
No video
1. Are the VLHD38 Power Buttons on both the Transmitter and
Receiver ON?
2. Ensure there is video on the output device (Source).
3. Check the receiver is correctly connected to display
equipment.
4. Make sure all devices are working on supported distance. Draw
them closer and try it again.
5. Is the VLHD38 USB Power Cables are used, make sure there is
enough output power on the USB Power Port (1.5A Minimum).
Power
LED off
1. Make sure the Power Adaptor or Power USB cable is correctly
connected and the voltage is 5V 1.5A or higher.
2. Make sure the power supply would not be interrupted.
Receiver
video
indicating
LED
abnormal
1. Make sure video and audio signals can be transmitted to receiver
successfully.
2. If there are video and audio signal on output devices, please
check the indicating LED to see if something got wrong with it.
3. Make sure the device is working within the supported distance.
Bad
picture
1. Ensure there is video on output devices.
2. Check if the receiver is correctly connected to display equipment
and there is no damage on joints and wires.
3. Make sure all devices are working on supported distance. Draw
them closer and try it again.
2-6-2016 13 ebode VLHD38
No sound
or bad
sound
1. Make sure the source equipment output support audio format.
2. Restart the transmitter and connect it again.
3. Make sure there is no disturbance from the same frequency
(4.9～5.9GHz) within 50cm (Wi-Fi modem, microwave etc.)
Register
failure
1.Ensure the distance between transmitter and receiver doesn’t
exceed supported distance. If it does, make them closer and try
it again.
2.Check if source device has been added on display equipment.
If it has, delete it and make registration again.
Connectio
n failure
1 Ensure the working distance doesn’t exceed supported distance.
If it does, make them closer and try it again.
2 Make sure source devices have been registered every time after
software update.
3 Ensure source devices and display devices have been registered.
4 If failure occurs again, delete all registered information and try
again.
5 When using the USB Power cables, make sure that the USB port
delivers sufficient Power. A minimum of 5V 1.5 Amp is required
to power the VLHD38. Please refer to the USB output device
manual to find out how much power the USB port can deliver.
Please also note that if a port delivers 1.5 Amp, and the USB port
is shared (example 3 ports), the output can be lower than 1.5
Amp when a second and/or third USB device is connected. We
recommend to test with the included Power adapters first. After a
successful connection, switch to USB Power cables (Receiver side
first) and retry.
Other
problems
If any other problems occur, please un-power all connected
devices and check again.
In case of any other problems, please read the frequently asked questions in part 5 first.
If this cannot help you to solve the problem, please visit our website and go to the FAQ
section. If there are any product firmware updates available they can be found on our
website
www.ebodeelectronics.eu.
5. Sample of use
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
2-6-2016 91 ebode VLHD38
DECLARATION OF CONFORMITY
Hereby, ebode declares that this VLHD38 is in compliance with the essential
requirements and other relevant provisions of the following Directives:
1) Directive 1999/5/EC of the European Parliament and of the Council of 9 March
1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity
2) Directive 2004/108/EC of the European Parliament and of the Council of 15
December 2004 on the approximation of the laws of the Member States relating to
electromagnetic compatibility
3) Directive 2006/95/EC of the European Parliament and of the Council of 12
December 2006 on the harmonization of the laws of Member States relating to electrical
equipment designed for use within certain voltage limits
4) Directive 2002/95/EC of the European Parliament and of the Council of 27 January
2003 on the restriction of the use of certain hazardous substances in electrical and
electronic equipment
5) Directive 2005/32/EC of the European Parliament and of the Council of 6 July 2005
establishing a framework for the setting of eco design requirements for energy-using
Technical data and copies of the original Declaration of Conformity are available and can
be obtained from ebode electronics: PB 25, NL-4264ZG, the Netherlands.
User Information for Consumer Products Covered by EU Directive 2002/96/EC
on Waste Electric and Electronic Equipment (WEEE)
This document contains important information for users with regards to the proper
disposal and recycling of ebode products. Consumers are required to comply with this
notice for all electronic products bearing the following symbol:
Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this
symbol on the product and/or its packaging must not be disposed of with
unsorted municipal waste. The symbol indicates that this product should
be disposed of separately from regular household waste streams.
It is your responsibility to dispose of this and other electric and electronic equipment via
designated collection facilities appointed by the government or local authorities. Correct
disposal and recycling will help prevent potential negative consequences to the
environment and human health.
For more detailed information about the disposal of your old equipment, please contact
your local authorities, waste disposal service, or the shop where you purchased the
product.
Page is loading ...
2-6-2016 93 ebode VLHD38
This product complies with Part 15C and Part 15E of FCC Rules.
Part 15: Subpart C—Radiated Emission Limits, Additional Provisions.
Part 15: Subpart E---Unlicensed National Information Infrastructure Devices.
This device complies with relative criteria CE Certification.
EN 60950-1:2006
Information Technology
Equipment ---Safety---
Part 1: General Requirements
EN 300440-01(V1.6.1)
Electromagnetic Compatibility and Radio Spectrum Matters (ERM)
Short Range Devices.
Radio equipment to be used in the 1GHz TO 40 GHz frequency range.
Part 1: Technical Characteristics and Test Methods
EN 301489-03(V1.4.1)
Electromagnetic Compatibility and Radio Spectrum Matters(ERM);
Part 3:Specific conditions for Short-Range Device(SRD)
Operating on frequency between 9 kHz and 40 GHz
EN 301489-17(V2.1.1)
Electromagnetic Compatibility and Radio Spectrum Matters(ERM);
Part 17:Specific conditions for Broadband Data Transmission Systems
EN 301893(V1.5.1)
Broadband Radio Access Network(BRAN)
5 GHz high performance RLAN
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Page is loading ...
Page is loading ...
2-6-2016 96 ebode VLHD38
www.ebodeelectronics.eu
/