Philips US2-PH61159 converts audio and video signals from devices like VCRs, DVD players, or satellite receivers into VHF TV signals for viewing on any regular TV set. It features S-video and standard video inputs, audio inputs, and two options for connecting to the TV. The modulator automatically switches between the connected video source and the antenna/cable signal.
Philips US2-PH61159 converts audio and video signals from devices like VCRs, DVD players, or satellite receivers into VHF TV signals for viewing on any regular TV set. It features S-video and standard video inputs, audio inputs, and two options for connecting to the TV. The modulator automatically switches between the connected video source and the antenna/cable signal.
Your Video RF Modulator is designed to convert the separate audio and
video signals (from a video camera, computer, portable VCR, satellite
receiver, DVD player, etc.) into normal VHF TV signals that you can see on
any regular TV set.
INTRODUCTION
This symbol is intended to inform you that important
operating and maintenance instructions are included
in the literature accompanying this RF Modulator.
This symbol is intended to alert you to the presence of
uninsulated dangerous voltage within the RF
Modulator’s enclosure that might be of sufficient
magnitude to constitute a risk of electric shock. Do not
open the RF Modulator’s case.
CAUTION
R
ISK OF ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
REFER SERVICING TO QUALIFIED PERSONNEL.
Warning:
For indoor use only; to reduce risk of fire or shock hazard,do not
expose this product to rain or moisture.
Video RF Modulator
Owner’s Manual
This device complies with Part 15 of the
FCC Rules
. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesirable operation.
Even under optimum conditions, your Video RF Modulator may cause
undesirable interference. We suggest the following methods for trouble
shooting
:
1. Use an AC outlet that is not the same circuit as the receiver.
2. Place the RF Modulator in a location further away from your receiver.
In the event that interference still occurs after the above steps have been
taken, you are required by FCC regulations to discontinue use of this
product.
Important Safety Information
:
1. Before beginning installation of your Video RF Modulator read all
instructions and follow exactly throughout the installation.
2. After installation is complete, keep all instructions in a safe place so
they may be referred to in the future if necessary.
3. Please note the ideal environment for this device is on a hard flat
surface away from all heat sources and moisture.
THE FCC WANTS YOU TO KNOW
You need the following items, not supplied with your Video RF Modulator,
to connect it between a video input source (video game, video camera,
satellite receiver, DVD player, etc.) and your TV.
• Two 75-ohm coaxial cables with F-type connectors
• If your TV does not have a VHF 75-ohm F-connector, you will also
need a 75-ohm-to-300-ohm matching transformer
•One video shielded cable with RCA Plugs and one audio (stereo)
cable with RCA Plugs OR Dubbing Cable for VCR/DVD with RCA
Plugs OR 3 shielded cables with RCA Plugs
•One S-Video Cable
PARTS REQUIRED
Follow these steps to connect your RF Modulator:
1. Connect an S-Video or video cable between the S-Video or video output
jack on your video source and the RF Modulator’s
S-VIDEO
or
VIDEO IN
jack.
CONNECTIONS
ANT IN
TO TV
LR
60Hz/4.5W
V
IN
S-VIDEO
Jack Jack
S-Video OutputVideo Output
OR
Video Source
Note:
If both the S-Video and standard video are hooked up,
the S-Video will be given priority
2. Connect an audio cable between the audio output jacks on your video
source and the RF Modulator’s
AUDIO IN
jacks.
AUDIO IN Jacks
Audio Output
Audio Source
ANT IN
TO TV
LR
60Hz/4.5W
IN
S-VIDEO
3. Connect the 75-ohm coaxial cables to the RF Modulator using one of
these two (2) options:
Option 1: If your TV is already connected to another VHF input source
(such as cable TV, VCR, etc.):
TO TV
CATV/ANT
VHF
RF Modulator VCR
ANT INT mhO 57VT O 75 Ohm
Disconnect
from here
a. Disconnect the current CATV/antenna connection from the 75-ohm
input terminal of your VHF source, and reconnect it to the RF
Modulator’s
ANT IN
terminal.
b. Then add a 75-ohm coaxial cable connected between the
TO TV
terminal of the RF Modulator and the 75-ohm input terminal of your
VHF source.
7
5 Ohm
CATV
3
00 Ohms
VHF
RF Modulator TV
ANT INTO TV
Option 2: If your TV is not already connected to another VHF source:
a. Disconnect the current CATV/antenna cable from the 75-ohm input
terminal of your TV, and reconnect it to the RF Modulator’s
ANT IN
terminal.
b. Then add a 75-ohm coaxial cable connected between the
TO TV
terminal of the RF Modulator and the 75-ohm VHF input terminal on
your TV.
Note:
If your TV has only 300-ohm VHF screw terminals, use a 75-ohm-
to-300-ohm matching transformer to complete the connection.
4. Plug the RF Modulator’s power cord into a standard AC outlet.
CONNECTIONS continued
75 Ohm75 Ohm
OUTIN
CATV
VHF
Add this cable
Reconnect
here
RF Modulator VCR
ANT INTO TV
TO TV
3. Turn on the connected video source, the modulator will deliver the
video/audio signal to the TV set and the red light of
MOD. ON
will be
ON
.
4.
Turn off the connected video source, the modulator will be switched
automatically to deliver the ANT/Cable signal to the TV set and the red
led of
MOD. ON
will be
off
.
1. Turn on the TV and set it to either Channel 3 or 4, whichever of the
two is not used for regular broadcasts in your area.
2. Set the RF Modulator’s
CHANNEL 3 or 4
switch to the same channel
you set on the TV (3 or 4)
OPERATION
4
3
MOD. ON
CHANNEL
SPECIFICATIONS
Video Carrier Output Level 63 dB uV
RF Output Channels 3 or 4
RF Output Impedance 75 ohms
Video Input Impedance 75 ohms/1 k ohms
Audio Input Impedance 13
±
3 k ohms
Specifications are typical, individual units might vary. Specifications
are subject to change and improvement without notice.
Limited Lifetime Warranty
The Manufacturer warrants that this product shall be
free from defects in material, workmanship and assembly, under normal use, in
accordance with the specifications and warnings, for the life of the product. This
warranty extends only to the original purchaser and is non-transferable. Defective
products must be returned with the dated proof of purchase to the place of
purchase for replacement. THERE ARE NO OTHER EXPRESS OR IMPLIED
WARRANTIES. Incidental or consequential damages are disclaimed where permitted
by law.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
Philips US2-PH61159 converts audio and video signals from devices like VCRs, DVD players, or satellite receivers into VHF TV signals for viewing on any regular TV set. It features S-video and standard video inputs, audio inputs, and two options for connecting to the TV. The modulator automatically switches between the connected video source and the antenna/cable signal.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Philips US2-PH61159 Manuel utilisateur
- español: Philips US2-PH61159 Manual de usuario
Related papers
Other documents
-
RCA CRF910 User manual
-
Pyle LMD7 Owner's manual
-
Dynex DX-AD116 User manual
-
Insignia NS-HZ308/NS-HZ308-C User manual
-
-
Insignia NS-HZ308/ NS-HZ308-C RF Modulator AV Signal Converter Quick setup guide
-
Marmitek MEGACAM1 User manual
-
Marmitek MegaView 70 User manual
-
Leviton 48213-VMA User manual
-
Engel MV7480 User manual
