Alarm Clock Radio with Dock for iPod
Thanks for buying a TEAC. Read this manual carefully to get the
best performance from this unit.
Safety Considerations
The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
To be completely disconnect the power input, the mains plug of
apparatus shall be disconnected from the mains.
The mains plug of apparatus should not be obstructed OR should be
easily accessed during intended use.
The marking information is located at the bottom of apparatus.
Battery shall not be exposed to excessive heat such as sunshine, fire or
the like.
Minimum distances around the apparatus for sufficient ventilation.
The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, table-cloths, curtains, etc;
No naked flame sources such as lighted candles should be placed on
the apparatus.
Attention should be drawn to environmental aspects of battery disposal;
The use of apparatus in moderate climate.
Electrical Information
Make sure that the voltage of your electricity supply is the same as that indicated on
the rating plate of the power supply unit supplied with your product. It requires a
compatible mains supply. Do not use any other supply.
1
IMPORTANT SAFETY
AC Operation
Your unit requires a mains supply. Please ensure that your mains supply is compatible before use.
Insert the mains cable into the power socket at the rear of the unit, and then insert the main plug into a
main supply socket. Press the POWER Button to ON position to operate the unit.
Use Aux In
Press Power Button to turn on the unit and select the Function Switch to iPod mode,
simply connect an audio cable (not included) from the AUX IN jacks on this unit to
external unit’s LINE OUT jacks and press the Function Button to AUX mode. This will
allow you to broadcast the external unit’s sound through this unit’s speakers.
Warning!
If connecting to the headphone output of an audio source, the source’s volume
controls may need to be adjusted for optimal sound.
Adjusting the Volume Sound
Rotate the Volume Buttons to increase / decrease the volume sound.
Dimmer Function
Slide the Dimmer Switch to HIGH / LOW dimmer to select LED brightness
Battery Operation (DC 9V) – For Clock Backup
The Battery Back-Up will save the clock and program settings in case of power outage.
The display / unit will not be active without AC power (batteries not included).
How to install or remove the battery : Remove the battery compartment cover on the
back of the unit by carefully pushing one lug of the battery cover. The battery cover can
then be lifted away. Fit 9V batteries (not included), referring to the polarity markings
inside the battery compartment.. Finally, replace the cover. For battery operation, switch
off the mains supply and remove the cable from the power socket, battery operation will
be selected automatically.
Warning!
Danger of explosion if batteries are incorrectly replaced.
Replace only with the same equivalent type.
2
POWER SOURCE
1 AC POWER CORD 13 PLAY / PAUSE Button
2 DIMMER Switch 14 FUNCTION Button
3 WAKE UP Switch 15 SKIP FORWARD Button
4 SKIP BACKWARD Button 16 TUNING Knob
5 VOLUME Knob 17 POWER Indicator
6 AUX Jack 18 POWER ON/OFF Button
7 SLEEP Button 19 AL. SET (ALARM SET) Button
8 TIME SET Button 20 PM (
CLOCK PM TIME
) Indicator
9 DISPLAY 21
AUTO (ALARM WAKE UP) Indicator
10
SNOOZE Button 22 SLEEP Indicator
11 FM Antenna
12
Dock for iPod
3
LOCATION OF UNIT
First Time Using the Unit
Insert the main plug into a main supply socket. After the connect press the Power On/Off Button
(top of the unit)
to ON mode to operate the unit.
Setting the Clock
1. Press the Power Button (top of the unit) to standby mode, then press and hold the
Time Button.
2. Use the Skip Forward & Backward Buttons to set the hour & minute respectively to
correct time.
Setting the Alarm Wake Up Time / Wake Up Source
1. Press the Power Button (top of the unit) to standby mode, then press and hold the
Alarm Set Button
.
2. Use the Skip Forward & Backward Buttons to set the hour & minute respectively to
correct alarm time.
Select the Wake Up Switch to select wake up source.
Select the Wake Source
1. After the alarm time setting, slide the Wake Up Switch to select wake up source.
2. You can select alarm sound from RADIO / IPOD / BUZZER. If select to
IPOD/RADIO, then you can select AM, FM or IPOD/AUX by sliding the
FUNCTION button.
3. After the setting press the Power Button to standby mode, you can wait for alarm
sound.
4. When alarm sound, press the Power Button to off the alarm sound and the alarm
will auto replay next day.
Snooze Function
When an alarm sounds, pressing the SNOOZE Button will temporarily silence the alarm
for 9 minute.
Setting the Sleep Timer
Press the Power Button (top of the unit) to on the unit,
1. Press the SLEEP button and "59" will appear on the clock display.
2.
When "59" will appear, then the unit will be automatic to turn off after 59 minutes.
3.
When press Sleep Button
and press the
Skip Forward & Backward Buttons to set the
hour and minute of sleep time from 1:59 to 0:01 minutes
4.
Cancel the sleep function, press the Power / Snooze Button to cancel sleep the Sleep
function will activate and the Sleep Indicator.
Warning!
To cancel the Sleep function : Press the Sleep Button until the SLEEP icon disappear.
4
OPERATION FOR THE CLOCK
Tuning the AM/FM Radio
1. Press the Power Button to turn the unit on.
2. Press the Function Button to switch between AM and FM radio.
3. Rotate the TUNING Knob to tune in your desired radio station.
4. Rotate the VOLUME Knob to adjust your desired listening level.
5. To turn off the radio, press the Power Button to turn the unit to standby mode.
Warning!
This unit has built-in AM ferrite bar antenna, which provides adequate reception in
most areas. If AM reception is week, turn the unit to improve reception. If FM
reception is week, adjust the length and the angle of the FM antenna.
Using the iPod Docking
When the unit is plugged in power, the docked iPod will automatic charge (except AM
mode)
1. Locate the numbered brackets that fit the iPod that will be docked. Each included
bracket has a number on it, indicating which iPod model that bracket is compatible.
2. Each included bracket has a number on it, indicating which iPod model that bracket is
compatible.
3. Dock an iPod onto the unit.
4. After the correct connection, press the Power Button to turn the unit on.
5. Slide the Function Button to switch to iPod mode.
6. Press the Play/Pause Button to begin playing the docked iPod.
7. During iPod playing , press the Play/Pause Button to pause playing and press again to
resume..
8. Press the Skip forward / Skip backward Buttons to skip from one song to the next
song on a docked iPod.
9. Press and hold the Skip forward / Skip backward Buttons to search through an
individual song from a docked iPod.
5
OPERATION FOR THE RADIO / iPOD
Power supply ------------------- 240V ~ 50Hz
Output rating ------------------- 2 X 0.8W RMS
Protection class ---------------- II
Net weight ---------------------- 0.7Kg
Frequency range --------------- FM 87.5-108 MHz
--------------- AM 520-1620 KHz
Power consumption------------ 10W
6
TECHNICAL SPECIFICATION
/