Sony Bravia KDL-52WL130PKG Owner's manual

Brand: Sony

Model: Bravia KDL-52WL130PKG

Type: Owner's manual

This manual is also suitable for

To Customers and Sony Dealers

3-218-211-11(1)

SU-FL300L

TV Stand

Instructions

Mode d’emploi

Instrucciones

SU-FL300M

2 (US)

Thank you for purchasing this product.

If the safety precautions are not observed or the product is

used incorrectly, it may result in serious injury or fire.

This instruction manual shows the correct handling of the

product and important precautions necessary to prevent

accidents. Be sure to read this manual thoroughly and use the

product correctly. Keep this manual available for future

reference.

For Sony dealers

Installation of a TV requires two or more people, special care

and technique. When installing a TV, refer to this manual

carefully. Sony is not liable for any accidents or damages

caused by incorrect installation or handling. Please give this

manual to the customer after installation.

Products by Sony are designed with safety in mind. Incorrect

use may result in a serious injury through fire, electric shock,

the product toppling over, or the product dropping. Be sure to

observe the precautions for safety to prevent such accidents.

Specified products

The following products are subject to change without notice.

Certain models may be out of stock or discontinued, or may

not be available in certain regions.

This TV Stand is designed for use with the products specified

above. For other TVs, refer to their operating instructions to

verify that the TV Stand can be used.

Some TVs are supplied with a leaflet explaining how to

install the TV Stand.

For customers

This product should only be installed by qualified Sony

service representatives, as it requires two or more people,

special care, safety, and technique.

WARNING

On Safety

CAUTION

LCD Color TV

SU-FL300M

KDL-46W3000

KDL-46V3000

KDL-46VL130

KDL-46S3000

KDL-40W3000

KDL-40V3000

KDL-40VL130

KDL-40D3000

KDL-40S3000

KDL-40SL130

KDL-32XBR4

KDL-32S3000

KDL-32SL130

SU-FL300L

KDL-52W3000

KDL-52WL130

KDL-46W3000

KDL-46V3000

KDL-46VL130

KDL-46S3000

3 (US)

Products should only be installed by

qualified Sony service

representatives.

The TV and the TV Stand are very heavy; installation by

non-qualified persons could result in serious injury.

Be sure to take measures to prevent

the TV Stand from toppling over.

If you fail to do so, the TV may topple over and cause injury.

Anchor the TV to a wall, etc., to prevent toppling over.

Be sure to install the TV Stand on a

solid and flat floor.

Do not install the TV Stand so that it leans in one direction. If

you do so, the TV Stand may topple over or the TV may fall.

This may cause injury or damage.

If you install the TV Stand on a soft surface such as a mat or

a carpet, lay a board over the designated location beforehand.

Do not use a cracked TV Stand.

Do not lean on or hang from the TV.

The TV Stand may topple over, or the TV

may fall and cause serious injury or death.

Do not allow children to climb on the

TV Stand or crawl between the

shelves.

If children climb on the TV Stand or get

between the shelves, serious injury or death

can result if the glass breaks or the TV Stand

topples over.

Do not step on the TV Stand.

You may fall, or break the glass and

cause injury.

Do not cover the ventilation holes of

the TV.

If you cover the ventilation holes (with a

cloth, etc.), heat may build up inside and cause

fire.

Do not allow the AC power cord or

the connecting cable to be pinched.

• Do not allow the AC power cord or the connecting cable to

be pinched when you install the TV on the TV Stand. If

the AC power cord or the connecting cable is damaged,

this may result in fire or electric shock.

• Do not step on the AC power cord or

the connecting cable when you carry

the TV Stand. The AC power cord or

the connecting cable may be damaged,

and this may result in fire or electric

shock.

Do not stumble over the AC power

cord or the connecting cables.

You may trip, or may cause the TV

Stand to topple over and cause injury.

Do not move the TV Stand with the

TV attached or with connected

equipment inside.

If you move the TV Stand with the TV

attached, it may hurt your back, or the

TV Stand may topple over and cause

serious injury. Also, any connected

equipment within may fall and cause the

glass shelf to break or other property

damage.

WARNING

If the following precautions are not observed,

serious injury or death can result through fire,

electric shock, or the product toppling over.

Do not use the TV Stand if it has

sustained any cracks. The glass may

break and cause the TV to topple over,

which could cause serious injury or

damage.

Cracked TV Stand

English

4 (US)

Do not install any equipment other

than the specified product.

• This TV Stand is designed for use with the specified

product only. If you install equipment other than specified,

it may fall or break, and cause injury.

• Do not place objects such as vases, pottery, etc., on the TV

Stand.

• Do not modify the TV Stand.

• Do not place anything hot directly on the TV Stand. The

heat may cause discoloration or deformation of the TV

Stand.

• Do not place anything directly on the TV Stand that may

damage the glass.

Be sure to secure the TV.

Secure the TV to the TV Stand using the supplied anchor

attachments. If the TV is not installed securely, it may fall, or

the TV Stand may topple over, and cause injury.

Do not apply weight to the glass or

subject it to any kind of impact.

Do not apply weight to the TV Stand with your hand when

installing the TV. Do not hit the TV Stand with hard objects,

such as a screwdriver, etc. The glass may break and cause

injury.

When carrying the TV Stand

Trying to move the TV Stand alone, or without following the

proper procedures, may cause injury. To avoid this, be sure to

follow the advice given below.

• Be sure that two or more persons carry the TV Stand, and

only after removing the TV, connected equipment and

glass shelves.

• Do not drag the TV Stand. The base parts of the TV Stand

may come off and damage the floor.

• Be careful not to allow your hands or feet to be pinched

under the Base Board.

• Do not grab the glass shelf when carrying the TV Stand.

Do not subject the glass to

excessive shock.

This TV Stand is made of

tempered glass, but care should

be taken.

If the glass breaks, glass

fragments could cause injury, so

observe the precautions below.

• Do not hit the glass or drop

sharp-pointed objects on the

glass. Avoid excessive shock.

• Do not scratch or poke the

glass with sharp-pointed

objects.

• Do not let hard objects such

as a vacuum cleaner hit the

edges of the glass.

Note on carrying capacity

Do not place any equipment

which exceeds the

maximum weight for each

shelf as indicated in the

illustration.

Otherwise, the shelves may

break.

Notes on installation

• When assembling, lay the packing materials on the floor to

avoid damage to the floor.

• Install the TV Stand on a solid and flat floor. Do not allow

the TV Stand to be installed at an angle or incline. To

avoid this, observe the following precautions.

– Do not install the TV Stand in a place subject to direct

sunlight or near a heater.

– Do not install the TV Stand in a hot or humid place, or

outdoors.

Note on use

To keep the TV Stand clean, occasionally wipe it with a dry

soft cloth. Stubborn stains may be removed by wiping with a

cloth slightly dampened with mild soap. Be sure to dry the

area afterwards with a dry soft cloth. Do not use chemicals,

such as thinner or benzine, as they damage the finish of the

TV Stand.

CAUTION

If the following precautions are not observed,

injury or property damage may occur.

30 kg (66 lb 2 oz)

5 (US)

Be sure that two or more persons do

the installation work.

Be sure that two or more persons install the TV on the TV

Stand. If one person does the installation work alone, this

may result in an accident or injury. Be sure to keep children

away during the installation.

Be sure to assemble the TV Stand

securely following the instructions.

If a screw is not tightened securely, or

it has fallen out, it may cause the TV

Stand to topple over. This may cause

damage or injury.

Be careful not to injure your hands

or fingers while assembling.

Be careful not to pinch your fingers or hands when

assembling the TV Stand and installing the TV.

Be sure to install the TV securely

following the instructions.

Tighten the screws securely. If the TV is not installed

securely, it may fall and cause injury.

The illustrations above are for SU-FL300L. This differs

from SU-FL300M. For SU-FL300M, there is a cutout part

on the side of the Side Pillar.

For SU-FL300M, three paper templates are provided, one

for each TV size (32/40/46 inch).

For SU-FL300L, two paper templates are provided, one

for each TV size (46/52 inch).

Be sure to have a Phillips screwdriver that fits the screws

indicated above prior to the assembly.

To Sony dealers

Be sure to thoroughly read the

safety precautions described

previously and pay special

attention to safety during the

installation, maintenance,

checking, and repair of this

product.

Step 1:

Checking the parts

Name Quantity

Top Board

Base Board

Side Pillar (L)*

Side Pillar (R)*

Rear Pillar

Front Panel

Glass Shelf

Screw (+PWH5 × 25)

Screw (+K4 × 20) + Sleeve

Cam-lock screw

Screw (+P4 × 15)

Anchor bolt

Screw cap

Speaker Hook (L)

Speaker Hook (R)

Paper template

Tape

6 (US)

Step 2:

Assembling the TV

Stand

If you allow the AC power cord to be pinched under or

between pieces of equipment, this may result in a short

circuit or an electric shock. If you stumble over the AC

power cord or the connecting cable, the TV Stand may

topple over and cause injury.

Decide on the installation location and lay the TV

Stand down before installing the TV.

Since the TV is heavy, it is recommended that you decide

on the installation location beforehand, and assemble the

TV Stand on site.

Attach the Rear Pillar to the Base

Board.

1 Tighten the two supplied Cam-lock screws to the

Base Board.

Arrow direction shows front of the TV Stand.

WARNING

Cam-lock screw

Base Board

2 Attach the Rear Pillar to the Base Board and secure

the two Cam-lock screws with a screwdriver.

Attach the Side Pillars to the

Base Board.

Secure the Side Pillars and the Base Board with the

four supplied screws (+PWH5 × 25).

Note

There are differences between the left and right pillars.

Be sure to install each pillar on the correct side.

Rear Pillar

Side Pillar (R)

Side Pillar (L)

Screw

(+PWH5 × 25)

7 (US)

Attach the Top Board.

1 Tighten the two supplied Cam-lock screws to the

Top Board.

The illustration shown above is SU-FL300L as an

example. For SU-FL300M, there is only one

reinforcing bar on the Top Board.

Notes

• To prevent damaging the glossy surface of the Top Board,

make sure to clean and place a soft cloth on the work

surface.

• If you attach the Home Theatre System to the TV Stand,

also refer to “Installing the Center Speaker (For Home

Theatre Systems only)” on page 11.

2 Align and insert fixing brackets either side of the

Top Board into the Side Pillars.

3 Secure the Side Pillars with the four supplied screws

(+PWH5 × 25). And secure the two remaining Cam-

lock screws on the back side of the Rear Pillar.

Note

Be careful not to pinch your fingers when attaching the Top

Board.

Soft cloth

Cam-lock screw

Top Board

Screw

(+PWH5 × 25)

Attach the Front Panel to the TV

Stand.

1 Align the three dowels of the TV Stand with the

three holes of the Front Panel.

2 Turn the six Cam-lock screws on the Top and the

Base Boards clockwise to secure the Front Panel.

And attach the three supplied screw caps to the

three bottom screws.

Note

Be sure to attach the Front Panel in the correct direction.

Front Panel

Dowel hole

Screw cap

(Continued)

8 (US)

Attach the Glass Shelf.

1 Fully insert the Glass Shelf into the Rear Pillar until

it touches the Rear Pillar.

Note

Attach the Glass Shelf to the TV Stand with the Caution label

at the front right, as shown in the illustration.

2 Tighten the four screws on the Side Pillars to secure

the Glass Shelf and the TV Stand.

Caution label

Glass Shelf

Step 3:

Preparing for the

installation of the TV

Attach the sleeves to the Top

Board.

Insert the sleeves of the two supplied screws (+K4 ×

20) into the two front-most holes, then secure with the

screws.

Note

The other two rear-most holes of the Top Board are not used.

Paste the supplied paper

template on the Top Board.

1 Choose the paper template of your TV size from the

supplied paper templates and align the right corner

edges of the paper template with the right corner of

the Top Board.

2 Tape the paper template to the Top Board with the

supplied tape.

Screw

(+K4 × 20)

Sleeve

Check your TV size.

Tape

Paper template

9 (US)

Step 4:

Installing the TV

Install the TV onto the TV Stand.

Referring to the outline of the supplied paper template,

match the outline of the Table-Top Stand to the paper

template outline, so that the holes at the bottom of the

Table-Top Stand align to the sleeves which were

attached in part 1 of the Step 3.

2 Slide the TV back to lock into place.

3 Remove the paper template from the Top Board.

Attach the anchor bolts.

Secure the two supplied anchor bolts to the rear of the TV.

Note

If the two anchor bolts are not used to secure the TV, it may

fall and cause injury.

Paper template

Anchor bolt

Step 5:

Safety measures to

prevent toppling over

WARNING

Be sure to take measures to prevent the TV Stand from

toppling over, and causing possible injury and damage.

Attach the support belt.

1 Screw the support belt (supplied with the TV) to the

TV Stand with the wood screw (supplied with the

TV) using the screwdriver.

2 Attach the support belt to the Table-Top Stand, and

screw the belt with the securing screw (supplied

with the TV) using a coin, etc.

3 Adjust the length by tightening the support belt

while holding the Table-Top Stand.

(Continued)

10 (US)

Design and specifications are subject to change without

notice.

Connect the cables.

Run the cables through the cable holders and the Rear

Pillar holes.

Note

If the cables are not installed properly, they might be pinched

and damaged, and could result in electric shock, etc.

Anchor the TV to the wall.

Prepare a strong, commercially-available rope or chain

and wall anchor bracket for this purpose.

1 Secure the wall anchor bracket to a solid wall.

2 Pass the rope or chain through both holes of the

anchor bolts and then tighten the other end of the

rope or chain to the wall anchor bracket.

Strong rope or

chain

Wall anchor bracket

Specifications

Do not place any equipment on the Glass Shelf which

exceeds its maximum weight, as it may break and cause

injury.

SU-FL300M SU-FL300L

Dimensions:

mm (inches)

A 1,035

(40 3/4)

1,280

(50 1/2)

B 503

(19 7/8)

503

(19 7/8)

C 487

(19 1/4)

518

(20 1/2)

D 895

(35 1/4)

1,140

(45)

E 303

(12)

303

(12)

F 418

(16 1/2)

468

(18 1/2)

G 146

(5 3/4)

146

(5 3/4)

H 120

(4 3/4)

130

(5 1/8)

I 272

(10 3/4)

340

(13 1/2)

Weight: 35 kg

(77 lb 3 oz)

52 kg

(114 lb 11 oz)

30 kg (66 lb 2 oz)

Note on carrying capacity

11 (US)

Installing the Center

Speaker (For Home

Theatre Systems only)

The Center Speaker model SS-CT71/CNP2200 is for

the following Home Theatre System models:

The Center Speaker model SS-CT72/CT74 is for the

following Home Theatre System models:

Notes

• The products above are subject to change without notice,

may be out of stock, or discontinued.

• Certain models may not be available in certain regions.

Before attaching the Speaker Hook:

For SS-CT71/CNP2200, the H-L/H-R markings should

face forward.

For SS-CT72/CT74, the S-L/S-R markings should face

forward.

DAV-HDX665

DAV-HDX466

DAV-HDX465

DAV-HDX267W

DAV-HDX266

DAV-HDX265

DAV-HDZ235

HT-SF2000

DAV-DZ556KB

DAV-DZ250KW

DAV-DZ250K

DAV-DZ151KB

DAV-DZ150K

DAV-HDX900W

DAV-HDX501W

DAV-HDX500

DAV-DZ1000

DAV-DZ850KW

Speaker hook screw for

SS-CT72/CT74

Speaker hook screw for

SS-CT71/CNP2200

Attach the Speaker Hook.

Secure each Speaker Hook with the supplied screws

(+P4 × 15) (two screws each for left/right) to the under

side of the Top Board.

Hang the Center Speaker onto

the hook screws as shown.

Speaker

Hook

Screw

(+P4 × 15)

Speaker

Hook

SS-CT71/CNP2200

SS-CT72/CT74

Screw

(+P4 × 15)

Center Speaker

Page is loading ...

Printed in Thailand

http://www.sony.net/

Sony Bravia KDL-52WL130PKG Owner's manual

Brand: Sony

Model: Bravia KDL-52WL130PKG

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: Sony Bravia KDL-52WL130PKG Le manuel du propriétaire
español: Sony Bravia KDL-52WL130PKG El manual del propietario

Sony Bravia KDL-52WL130PKG Owner's manual

This manual is also suitable for

Sony Bravia KDL-52WL130PKG Owner's manual

in other languages

Related papers

Other documents