Z5091
Ci Flying bracket
Mounting instructions
(4.0EN)
Contents
1. Product description...............................................................................................3
2. Scope of supply....................................................................................................3
3. Load safety information.....................................................................................3
4. Weight/Dimensions.............................................................................................3
5. Assembly.................................................................................................................4
5.1. Safety precautions.......................................................................................4
5.2. Mounting the bracket to the cabinet......................................................4
5.3. Deployment of the Ci7-TOP......................................................................4
6. EC Declaration of Conformity..........................................................................5
References in the manual
WARNING!
This refers to a potentially dangerous situation which
may lead to personal injury.
CAUTION!
This refers to a potentially dangerous situation which
may lead to damage to the equipment.
IMPORTANT!
This refers to a situation which may cause the equipment
to malfunction.
Note:
Additional informations
Symbols on the equipment
Please refer to the information in the operating manual.
General information
Z5091 Ci Flying bracket
Mounting instructions
Version 4.0EN, 10/2006, D2936.EN .04
Copyright © 2006 d&b audiotechnik AG; alll rights reserved.
Keep this manual with the product or in a safe place
so that it is available for future reference.
d&b audiotechnik AG
Eugen-Adolff-Strasse 134, D-71522 Backnang
Telefon: +49-7191-9669-0, Fax: +49-7191-95 00 00
E-mail: [email protected], Internet: www.dbaudio.com
Z5091 Ci Flying bracket
Fig. 1: Z5091 Ci Flying bracket
1. Product description
The Z5091 Ci Flying bracket is designed for indoor applications and
enables a single Ci7-TOP, Ci7-SUB, Ci4-TOP or Ci-SUB loudspeaker
cabinet to be suspended at any vertical and horizontal angle.
The bracket provides five 13 mm holes for fitting Q9030 M12 Safety
eye bolts.
A Z5018 TV spigot M12 can be attached in the centre hole of the tie
bar.
[1 ]
[2]
[2.1]
[2.2]
[3]
[4]
[4.1]
[4.2]
Fig. 2: Z5091 Ci Flying bracket,
Scope of supply
2. Scope of supply
The Z5091 Ci Flying bracket [1] is supplied with:
− 2 x Bolt M16 x 40 [2] together with:
− 2 x Spring washer [2.1]
− 2 x U washer [2.2]
− 2 x Pozidrive screw 4 x 20 [3]
− 2 x M12 Safety eye bolt [4] with:
− 2 x U (plain) washer [4.1]
− 2 x Self locking nut M12 [4.2]
− Mounting instructions.
3. Load safety information
The Z5091 Ci Flying bracket is designed to support one
Ci7-TOP, Ci7-SUB, Ci4-TOP or Ci-SUB loudspeaker cabinet
which is equal to a maximum weight of 60 kg (132 lb)
according to the German standard BGV C1. No additional
loads must be added.
4. Weight/Dimensions
Weight...................................................................................................................6 kg/13 lb
580 [22.8"]
510 [20.1"]
590 [23.2"]
13 [0.5"]13 [0.5"]
489 [19.3"]
13 [0.5"]
6 [0.25"]
17 [0.7"]
95 [3.7"]
78 [3.1"]
13 [0.5"]
Z5091 Mounting instructions (4.0EN) Page 3 of 6
5. Assembly
5.1. Safety precautions
Fig. 3: Vertical array with two
Ci7-TOP. Both cabinets suspended
independently.
Installation should only be carried out by fully trained personnel. There
are certain rules for installation that must be complied with.
It is the responsibility of the person installing the assembly to ensure that
the structure being attached to is suitable for the intended use.
The Z5091 Ci Flying bracket must only be used to suspend a single d&b
Ci7-TOP, Ci7-SUB, Ci4-TOP and Ci-SUB loudspeaker cabinets as
described in this mounting instructions.
The bracket must only be used to support the cabinet from the top, i.e.
both side arms of the bracket must point vertically downward.
To set up an vertical array of e.g. two Ci7-TOP cabinets, each cabinet
with the mounting bracket assembly must be suspended from two
separate and independently rigged suspension points.
All additional rigging parts used must have a suitable load safety factor
and safety approval for their intended load.
Eye bolts or a TV spigot have to be firmly secured using M12 self locking
nuts and spring washers.
Secondary safety must always be provided when suspending
loudspeaker cabinets overhead.
5.2. Mounting the bracket to the cabinet
[2]
[2.1]
[2.2]
[3]
Fig. 4: Z5091 Ci Flying bracket assembly
The bracket is fixed to the M16 threaded inserts of the cabinet side
panels using the supplied M16x40 bolts [2], spring [2.1] and plain
washers [2.2].
The vertical angle of the cabinet can be set before fully tightening the
bracket fixing bolts.
To finally lock the cabinet in place a pair of pozidrive screws (4x20) [3]
are inserted through holes provided on each side of the bracket and
screwed into the cabinet sides.
Five 13 mm holes are provided in the bracket for fitting M12 safety eye
bolts [4] (Q9030) or a Z5018 TV spigot M12 (centre hole of the tie bar).
5.3. Deployment of the Ci7-TOP
The Ci7-TOP can be deployed for either 75° x 40° or 40° x 75°
coverage depending on which pair of M16 threaded inserts are used to
mount the Z5091 Ci Flying bracket.
a) b)
Fig. 5: Deployment of the Ci7-TOP for either 75° x 40° (a) or 40° x 75°
(b) coverage using the Z5091 Ci Flying bracket
Z5091 Mounting instructions (4.0EN) Page 4 of 6
EC Declaration of conformity
6. EC Declaration of Conformity
within the meaning of the EC Machine Directive 98/37/EEC
We hereby declare that the equipment designated below is designed and built in the version sold by us in such a way as to
comply with the relevant fundamental safety and health criteria of the applicable EC Directive(s). This declaration shall
cease to be valid if alterations are made to the equipment without our prior agreement.
This declarations covers:
• Z5091 Ci Flying bracket
To be used as described in this mounting instructions
National standards and technical specifications applied, in particular:
DIN 18800-1, DIN EN 1050, DIN EN ISO 12100
Backnang, 2006-10-13
(Frank Bothe, Vorstand)
d&b audiotechnik AG, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone +49-7191-9669-0, Fax +49-7191-95 00 00_______
D2936.EN .04, 10/2006 d&b audiotechnik AG
d&b audiotechnik AG, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone +49-7191-9669-0, Fax +49-7191-95 00 00_______
-
1
-
2
-
3
-
4
-
5
-
6
D&B Z5091 Ci Flying bracket – Mounting instructions
- Type
- Mounting instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
D&B Ci7-TOP Owner's manual
-
-
-
-
-
-
-
-
-