Wirepath WPS-365-BUL-A-GR Owner's manual
- Category
- Security cameras
- Type
- Owner's manual
This manual is also suitable for
WPS-365-BUL-A
CAMERA
BULLET
INSTALLATION MANUAL
Review manual thoroughly before installation.
Retain for future reference.
2
WPS-365-BUL-A Installation Manual
CONTENTS
Safety Instructions ......................................................................................3
Features ......................................................................................................4
Package Contents ....................................................................................4
Installation Instructions ...............................................................................5
Troubleshooting ..........................................................................................8
Specications .............................................................................................9
Dimensions .................................................................................................. 10
Warranty .....................................................................................................11
Contacting Technical Support .................................................................11
3
WPS-365-BUL-A Installation Manual
© 2014 Wirepath Surveillance
SAFETY INSTRUCTIONS
This information is provided to ensure your safety and to prevent physical
or nancial loss. Please read this document carefully before installing and
operating the camera.
1. Handle with care.
This camera is not designed to resist heavy impact. Use caution when
handling to avoid damage to sensitive internal components.
2. Do not install the camera under extreme temperatures.
This camera only operates under temperature conditions between
14˚F ~ 140˚F.
3. Do not mount the camera directly facing bright light sources.
Exposing the camera to strong light over long periods of time will damage
the camera’s sensor.
4. Do not supply voltage other than 12VDC.
Higher voltages will damage the camera’s electronic components.
5. Do not install the camera in environments with extreme humidity.
Installing the camera in environments with extreme humidity may cause
moisture to condense on the surface of the lens or dome cover, which can
affect picture quality.
4
WPS-365-BUL-A Installation Manual
FEATURES
• 960H 1/3” Sony Super-HAD II CCD
The 960H Sony Super HAD II CCD is ideal for low lux illumination, resulting in a
clear and crisp image.
• Varifocal Auto-Iris Lens
This camera features a varifocal lens with a focal length of 2.8~12 mm. The
auto-iris function intuitively manages the amount of light passing through the
lens for consistent image brightness.
• Weatherproof Housing
The IP66-rated weatherproof housing makes this camera ideal for
outdoor surveillance.
• Video Test Port
Adjust angle, zoom, and focus at the camera for fast and easy installation.
• External Zoom and Focus Adjustments
Adjust the camera without the need to remove the lens cap for quick
adjustments.
PACKAGE CONTENTS
(1) WPS-365-BUL-A
(1) DC Power Plug with Screw Terminals
(1) BNC Test Port Adapter
(4) Screws
(4) Wall Fasteners
(1) 3mm Allen Key
(1) Foam Gasket
(1) Installation Manual
(1) Spare Silica Pack in Vacuum Sealed Bag
NOTE: A POWER SUPPLY IS NOT INCLUDED WITH THIS CAMERA.
The PS-12DC-1A or WPS-PS multiple output power supplies are recommended.
5
WPS-365-BUL-A Installation Manual
© 2014 Wirepath Surveillance
INSTALLATION INSTRUCTIONS
Step 1. Prepare Camera for Mounting
Prior to mounting the camera, take into account the angle-of-view limits.
Ensure that the bullet camera can be aimed toward the desired eld of
view.
A. Adjust camera rotation
B. Adjust swivel of camera
C. Adjust camera angle
Note: Use the included 3mm Allen key to
make adjustments. Hand tighten only.
Step 2. Connect the Camera to the System
Recommended Cabling:
• Video - RG59 or RG6
• Power - Cat5e/6 or 18/2
A. Connect the BNC video output to the video input of a DVR or monitor.
B. Connect the DC Power In to a 12V DC 1A power supply using the included
WPS-ACC-PWR DC power adapter on the wire.
Important Note! If voltage is incorrect or polarity is reversed, the camera will
protect itself and will not power on. If you notice this, disconnect the camera
from the power source immediately and verify if voltage and/or polarity is
correct.
A
B
C
12V DC Power
BNC Video
Output
DC Plug
6
WPS-365-BUL-A Installation Manual
Step 3. Mount the Camera
A. Mounting directly to a wall or eve:Use the camera base as a template
to mark screw locations.
A.1. Pre-drill holes in the marked locations.
A.2. Connect the wires from the wall to the camera’s pigtail and
insert them into wall.
A.3. Place the included foam gasket over the base if desired, and
position the camera base over the marked holes from step
A.1.
A.4. Secure the camera with the provided screws.
B. Mounting to a single gang junction box:
We recommend the use of the WPS-MNT-FLUSH-BUL ush mount
plate when mounting to a single gang junction box. This plate is
available in gray or white to match the color of the camera being
used. Follow the instructions in the WPS-MNT-FLUSH-BUL manual for
using this mounting method and then proceed to step 4.
7
WPS-365-BUL-A Installation Manual
© 2014 Wirepath Surveillance
Step 4. Fine-Tuning Camera Adjustments
The camera is supplied with a BNC test adapter that plugs into the
camera test port. This allows for viewing the output of the camera on a
monitor or the WPS-CCTV-TESTER (not included). Use this connection to
view and adjust the camera’s positioning, zoom, and focus directly from
the installed location.
A. Remove the plate located at the rear of the cameras, just before the
camera’s base to access the BNC test adapter connection.
B. Connect the BNC test adapter to the camera.
C. Connect the BNC on the adapter to a monitor or WPS-CCTV-TESTER video
in.
D. Adjust the camera’s rotation, swivel, and angle as dened in step 1
and secure the set screws using the supplied 3mm Allen key.
E. Adjust the camera’s zoom (closest to the lens) using the supplied 3mm
Allen key.
F. Adjust the camera’s focus (furthest from the lens) using the supplied
3mm Allen key.
G. Once the zoom and focus are adjusted, disconnect the BNC test
adapter and replace the plate removed in step 4-A.
Adjust Zoom
Adjust Focus
BNC Test Adapter
Connection
8
WPS-365-BUL-A Installation Manual
TROUBLESHOOTING
If you have trouble operating the camera, rst refer to the following guidelines.
If the problem persists, contact Technical Support at (866) 838-5052.
Nothing appears on the display:
• Check if the power for the camera and the monitor is ON.
• Check if the VIDEO cable is connected to the camera BNC video output jack.
• Check if the VIDEO cable is connected to the monitor VIDEO input jack.
Image appears dim on the display:
• Check the monitor contrast setting.
• Check the monitor brightness setting.
• Check the lens. If necessary, clean with a soft, clean eyeglass cloth.
• Check if the camera is facing toward a bright light. If so, change the camera
position.
• If a device exists between the camera and screen, conrm the signal accepted by
the screen is strong enough – 75 Ohm.
Image appears blurry on the display:
• Check the focus of the lens.
• Check the lens. If necessary, clean with a soft, clean eyeglass cloth.
The camera is not working properly and the camera housing is hot:
• Check if camera is connected to the correct power source.
Condensation Appears on Camera Lens Cover:
• Change the desiccant pack inside the camera housing.
Camera Power Cycles Intermittently:
• Check voltage at camera for proper voltage level.
• Connect camera locally with a different power supply to test.
9
WPS-365-BUL-A Installation Manual
© 2014 Wirepath Surveillance
SPECIFICATIONS
Imaging
Image Sensor 960H 1/3" Color Sony Super HAD II
Lens 2.8 ~ 12mm Varifocal Auto Iris Lens
Estimated Horizontal Viewing Angle
92˚(W) ~ 30˚(T)
Resolution (TVLs) 650 TV Lines
Effective Pixels
NTSC: 976(H)x494(V)
Gamma 0.45
S/N Ratio >50dB
Sync. Mode Internal Sync
Scanning System 2:1 Interlace
IR Range 65ft
Auto IRIS Yes
Smart IR Yes
Technology
Minimum Illumination 0.01 Lux color, 0 Lux IR on
2D DNR Yes
Auto Gain Control Yes
Back Light Compensation Yes
White Balance Yes
Housing & Power
Weather Rating IP66
Operating Temperature
14
˚
F ~ 140
˚
F
Operating Humidity
30 ~ 80% RH
Power Source 12V DC (1A minimum) – Not included
Power Consumption 3.6W 300mA
Dimensions Dimensions on next page
Weight 1.7 lb
10
WPS-365-BUL-A Installation Manual
DIMENSIONS
3.4in.
3.82in.
8.39in.
9.07in.
Ø 3.06in.
1in.
0.6in.
3.2in.
11
WPS-365-BUL-A Installation Manual
© 2014 Wirepath Surveillance
WARRANTY
5-Year Limited Warranty
This camera has a 5-Year Limited Warranty. The warranty includes parts
and labor repairs on all components found to be defective in material or
workmanship under normal conditions of use. This warranty shall not apply
to products that have been abused, modied, disassembled, or improperly
installed. Products to be repaired under this warranty must be returned to
Wirepath™ Surveillance or a designated service center with prior notication
and an assigned return authorization number (RA).
CONTACTING TECHNICAL SUPPORT
Phone: (866) 838-5052
Email: [email protected]
140410-1143
© 2014 Wirepath Surveillance
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Wirepath WPS-365-BUL-A-GR Owner's manual
- Category
- Security cameras
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Wirepath Surveillance WPS-765-BUL-AH-WH Owner's manual
-
Wirepath WPS-565-BUL-A-WH Owner's manual
-
-
-
-
-
-
-
-
