Tailgate Alert
USE & CARE INSTRUCTIONS
Model No. 7001
1-Year Limited Warranty
Guardian Technologies
26251 Bluestone Blvd. • Euclid, OH 44132
www.guardiantechnologies.com
1.866.603.5900
REV1115
WARNING. Contains Strong Magnetic Sensor
Can be harmful to pacemaker wearers and others with medical
implants. Keep credit cards, computer disks, and other magnetic
storage devices away from the magnet. Keep electronic devices,
such as computers, away from the equipment because exposure
to the magnetic field may result in malfunction or permanent
damage to such devices.
LIMITED WARRANTY
To the consumer, Guardian Technologies LLC warrants this product to be free of defects in materials
or workmanship commencing upon the date of the original purchase. Save your original sales
receipt to validate start of warranty period. Warranty is not valid without receipt.
If this product should become defective within the warranty period, we will repair or replace any
defective parts free of charge. All warranty repairs must be completed by Guardian Technologies
LLC. This warranty does not cover unauthorized repairs. The warranty does not include unusual
wear, damage resulting from accident, or unreasonable use of the product. This warranty only
covers the product when used with genuine Guardian Technologies accessories. This warranty
covers product that was purchased from authorized distributors. This warranty gives you specific
legal rights and you may also have other rights (other rights may vary from state to state in
the U.S.A.)
The product warranty registration can be completed online at
www.guardiantechnologies.com. We consider the registration process important to ensuring
superior service to our customers, however submitting the warranty registration is optional and
does not affect your rights to utilize this warranty according to the conditions stated above. To
submit product under warranty the complete machine must be delivered pre-paid to Guardian
Technologies LLC. Please include complete information including: the problem, the model number
of the product, the day of purchase, and a copy of the original sales receipt along with your name,
address, and telephone (email optional). Address returns to the attention of: Customer Service,
at the address below. Additional questions or comments can be made toll free to the number
listed below.
Guardian Technologies LLC
26251 Bluestone Blvd.
Euclid, Ohio 44132
1.866.603.5900
www.guardiantechnologies.com
Additional copies of the instruction manual can be obtained by accessing and
printing directly from our website or calling customer service.
English E - 1
French F - 1
Spanish S - 1
Date Purchased
month ________
year _________
E-1
BATTERY
BATTERY
READ AND SAVE THESE INSTRUCTIONS
WARNINGS
Failure to comply with the warnings listed below may
result in electric shock or serious injury.
This product should be used only in accordance with the specifications outlined in this
manual. Usage other than what has been specified here may result in serious injury.
• Disassembly, repair or remodeling by an unauthorized person may result in serious harm
and will void the manufactures warranty.
• Manufacturer does not accept any liability for damage in the case of the unit being
placed incorrectly.
• Do not use if unit is damaged.
• Do not handle the unit with wet hands.
• Recycle batteries properly.
WARNING: THE CORDS, WIRES AND/OR CABLE SUPPLIED WITH
THIS PRODUCT CONTAIN CHEMICALS, INCLUDING LEAD OR LEAD
COMPOUNDS, KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
WASH HANDS AFTER USING.
(CALIFORNIA CODE OF REGULATION PROPOSITION 65)
WARNING. Contains Strong Magnetic Sensor
Can be harmful to pacemaker wearers and others with medical implants.
Keep credit cards, computer disks, and other magnetic storage devices away
from the magnet. Keep electronic devices, such as computers, away from the
equipment because exposure to the magnetic field may result in malfunction
or permanent damage to such devices.
SET UP INSTRUCTIONS - INSTALL BATTERY
1. Loosen the screw on the main module
with a screwdriver.
2. Insert flat head screwdriver into opening
on both sides of module cover and pry to
remove cover.
4. Realign cover tabs with slots and
assemble making sure its properly sealed.
Return screw and tighten with screwdriver.
Tailgate Alert INSTALLATION
SELECT LED SIGNAL, MODULE and SENSOR LOCATIONS FOR INSTALLATION IN TRUCK
Before adhering, determine location of all 3 components using following guidelines.
After marking locations for each component, clean all surfaces where components
will be placed with rubbing alcohol.)
MODULE/LED SIGNAL:
Select location on the inside of the truck bed side panel to adhere the Module.
Select a location that allows the LED signal to rest on the top of the truck and direct the
LED light to the drivers side mirror. The driver should see the LED in the side mirror clearly
(fig. 1). LED signal device aligns with drivers side mirror. Bulb facing forward (fig. 2).
PARTS AND ASSEMBLY
Main Module
Power Button
2 AA Batteries
(included)
Sensor
(magnetic)
LED Signal
3. Install the 2 AA batteries in
compartment aligning polarity.
1
Screws
(optional)
2
BATTERY
BATTERY
E-2 E-3
MODULE/SENSOR:
Select location for the model on the inside of the truck bed (fig 3). Important: The
location of the Module must correspond with the Sensor device. When the gate is
closed, the Sensor device must be within 1” of the module to send the signal. It should
be as close to the Module unit as possible without touching it (fig 4).
Module placed on the inside side panel of
the back of the truck and allows LED Signal
device to reach top of panel.
When gates closed the module and
sensor are within 1” without touching.
Module
1. After marking locations for each component, clean all surfaces where components
will be placed with rubbing alcohol.
2. Adhere Module: Remove adhesive
paper and adhere to inside of truck
bed. Make sure LED signal is facing
correct direction and sits on truck
panel as outlined previously.
3. Remove adhesive paper and adhere the
LED Signal directly to the top bed rail on
the outside of the cover of the car.
Note: The LED bulb should face the trucks
side mirror
4. Remove adhesive paper and adhere the Magnetic
Sensor directly to gate of the truck, making sure
that when the gate is CLOSED it’s within 1”
proximity to the Module.
Note: Adhesive can be removed from
vehicle using rubbing alcohol.
Operating Instructions
1. Turn unit on by pressing the power button on the side of the main module –
one red flash will appear on the LED signal the power is “on”.
2. If the Tailgate is left open, the Magnetic SENSOR (installed on the gate) will
activate the switch on the MAIN MODULE and the connected LED Signal
(installed on the truck) will then send a light signal that can be seen in the
drivers side mirror that the gate is down.
An Open Tailgate = 1 red flash every 2 seconds on the LED.
3. Close the Tailgate. No LED signal will appear.
Note: if Low Battery the LED signal will flash yellow 2 times every minute.
Troubleshooting
Not turning on.
1. Check to make sure the switch is “ON”.
2. Check if the battery installed properly.
3. Change batteries
When car tailgate is closed, if LED continues to flash signaling tailgate is open.
1. Check if the sensor has the magnet in the case.
2. Check the distance of the sensor to sensor module, it needs to be within
1" of sensor module end that is opposite the switch.
5. Optional screws (included)
can be used as a permanent
alternative to the adhesive.
3
4
Sensor
E-4
E-5
INSTALL MODULE, LED SIGNAL and SENSOR
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/