B-Speech Rx2 User manual

Page is loading ...

- 2 -

FCC Information

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device

must accept any interference received; including interference

that may cause undesired operation.

Federal Communications Commission (FCC) Statement

This Equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interfe-

rence will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- 3 -

- Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician

for help.

Warning:

Changes or modifications to this unit not expressly appro-

ved by the party responsible for compliance could void the

user authority to operate the equipment.

Tested to comply with FCC standard. FOR HOME OR

OFFICE USE.

Warning :

This equipment complies with FCC RF radiation exposure

limits set forth for an uncontrolled environment. & This devi-

ce and its antenna(s) must not be co-located or conjunction

with any other antenna or transmitter.

Europe–EU Declaration of Conformity

This device complies with the specifications EN 300 328,

EN 301-489 and EN 60950-1 following the provisions of the

R&TTE Directive.

B-Speech® Stereo Transmitter RX2

User guide

Introduction

The B-Speech

®

RX2 offers the latest in Bluetooth

®

technology Version 2.1. The B-Speech

®

RX2 Receives

Music Data from players which are compatible with

Bluetooth

®

with A2DP Profile.

The B-Speech

®

RX2 can be used with any audio Player or

Speaker with a 3.5 mm or Cinch audio input.

Technical data:

· Bluetooth

®

V. 2.1, Class II, 10 meters

· Bluetooth

®

stereo profile: A2DP

· Frequency: 2.4 GHz

· Certified CE and FCC

· 3,5 mm stereo Inlet socket

· Sleep mode for energy saving

· Power supply: charging via mini USB cable

· Operation time: max. 8 hours

· Dimensions: 49mm x21mm x12mm

GB

- 4 -

Start

The contents of the package consist of:

· B-Speech

®

stereo Receiver RX2

· Cable charger USB (portable charger optional)

· 3,5 mm Stereo Connector Male Plug / Plug

· 3,5 mm Stereo Connector Male Plug / Cinch

· This user guide

Please check that all the parts are present and intact. Contact

your dealer as soon as possible if anything is missing or

damaged.

Get acquainted with

the B-Speech

®

RX2

GB

- 5 -

LED indicator

(under the cover)

On / Off switch

Mini USB charger

connection

3,5 mm stereo

Inlet socket

GB

- 6 -

Charging

1. Connect the cable charger mini USB plug to the mini

USB input of the B-Speech

®

RX2.

2. Connect the USB plug on the other end of the cable

charger to the USB input of your PC or laptop. The LED

lights up during charging.

3. When charging is done, the LED will go off.

4. Remove the cable charger

Pairing

Pairing the B-Speech

®

RX2 with Bluetooth

®

Audio source

"Pairing" means establishing a wireless connection between

the Bluetooth

®

audio source and the B-Speech

®

RX2.

To be able to use B-Speech

®

RX2 with a audio source, you

need to pair them.

After pairing, you can use B-Speech

®

RX2 with your

Bluetooth

®

Audio source.

The pairing process in detail

1. Before pairing, please check that both devices are fully

charged.

2. Ensure that there is no other active Bluetooth

®

device

around.

3. Turn the RX2 ON by pressing the On / Off button for 7

Seconds. The red/blue LED will flash alternately,

GB

- 7 -

RX2 is in pairing mode.

4. Search for the RX2 on your Bluetooth

®

Mobile or Bluetooth

®

Audio transmitter. Pair the RX2 with your device and

enter the pairing code „0000".

5. Both devices should now find each other and pair.

The LED on the RX2 flashes slowly after successful

pairing.

6. The LED of the RX2 will turn blue, when both devices

are connected.

Note: Some Handsets need to be connected after pairing

and require authorisation. Please follow your handset's

manual for these additional steps.

Turning B-Speech® RX2 On/Off

The B-Speech

®

RX2 is turned on by pressing the On/Off

button for 4 Seconds. The blue LED will light up.

The B-Speech

®

RX2 is turned off by pressing the On/Off

button for about 5 seconds; the blue LED will go off.

Note: Read the user guide of your Bluetooth

®

transmitter to

find out how to turn it on / off.

GB

- 8 -

Playing music

1. Connect the RX2 with the delivered audio connection

wires with your home or car entertainment equipment or

any speaker system.

2. Make sure the transmitter (mobile phone or any A2DP

Bluetooth

®

source) is turned on and paired with RX2

within10 Meters.

3. The blue LED from the B-Speech

®

RX2 indicates that a

Bluetooth

®

connection exists by flashing slowly.

4. Send the music from your Bluetooth

®

source to the

B-Speech

®

RX2

If the connection disappears, the sound is disrupted or

breaks down: Move the transmitter nearer to the RX2.

If the connection does not automatically follow, start the

pairing process again.

Please note:

1. If for any reason the B-Speech

®

RX2 does not play any

music, it should be restarted.

To reset the B-Speech

®

RX2, repeat the paring process

as described above.

2. Normally, the connection between the transmitter and the

receiver is established once the pairing process is done.

The connection can break for the following reasons:

GB

- 9 -

- The distance between the devices is more than 10

meters or there is an obstacle between the devices.

- One or both of the devices have been turned off or must

be recharged.

Note on environmental protection:

After the implementation of the European Directive

2002/96/EU in the national legal system, the following

applies: Electrical and electronic devices may not be dis-

posed of with domestic waste. Consumers are obliged by

law to return electrical and electronic devices at the end of

their service lives to the public collecting points set up for

this purpose or point of sale. Details to this are defined by

the national law of the respective country.

This symbol on the product, the instruction manual or the package indi-

cates that a product is subject to these regulations. By recycling, reu-

sing the materials or other forms of utilising old devices, you are making

an important contribution to protecting our environment.

B-Speech® declares herewith that this device carries the CE mark in

accordance with the regulations and standards of the guideline R&TTE

(1999/5/EG). It conforms with the fundamental requirements, the

appropriate regulations and rules of the guideline 1999/5/EG.

You can find the complete declaration of conformity under

www.b-speech.com.

Page is loading ...

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.

and any use of such marks by B-Speech is under license.

1.A 06.09

B-Speech Rx2 User manual

B-Speech Rx2 User manual

in other languages

Related papers

Other documents