DeWalt DCF060 User manual

Brand: DeWalt

Model: DCF060

Category: Power tools

Type: User manual

DCF060

Destornillador Inalàmbrico

Parafusadeira sem fio

Cordless Screwdriver

MANUAL DE INSTRUCCIONES

MANUAL DE INSTRUÇÕES

INSTRUCTION MANUAL

INSTRUÇÕES DE OPERAÇÃO, CENTRO DE SERVIÇOS E CERTIFICADO

DE GARANTIA. ADVERTÊNCIA: LEIA ESTAS INSTRUÇÕES ANTES DE

UTILIZAR O PRODUTO.

¿Dudas? Visítenos en Internet: www.dewalt.com

Dúvidas? Visite-nos na Internet em www.dewalt.com.br

Questions? See us on the World Wide Web at www.dewalt.com

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL

PRODUCTO.

Page is loading ...

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool”in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

English

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energising power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

English

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional Speciﬁ c Safety Rules

• Hold power tool by insulated grippng surfaces, when

performing an operation where the fastener may contact

hidden wiring. Fasteners contacting a “live” wire may make

exposed metal parts of the power tool “live” and could give the

operator an electric shock.

CAUTION: INDOOR USE ONLY.

WARNING: ALWAYS USE SAFETY GLASSES. Everyday

eyeglasses are NOT safety glasses. Also use face or dust mask if

cutting operation is dusty. ALL USERS AND BYSTANDERS MUST

ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with

soap and water. Allowing dust to get into your mouth, eyes, or

lay on the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropriate

for the dust exposure. Direct particles away from face and body.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W .....................watts

min ............... minutes

or AC ..........alternating

or DC ...direct current current

................. Class I Construction or AC/DC ...alternating

.....................

(grounded) ........................or direct

................. Class II Construction current

(double insulated)

o ....................no load

…/min ..........revolutions per minute

....................... speed

BPM ............. beats per minute

n ......................rated

IPM ............... impacts per minute

........................speed

SPM ............. strokes per minute

.....................earthing

sfpm .............surface feet terminal

..................... per minute .....................safety alert

..................... symbol

Safety Warnings and Instructions:

Charging

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

English

• Before using the charger, read all instructions and cautionary

markings on the charger and product using the battery.

CAUTION: To reduce the risk of injury, use charger only with this

product. Batteries in other products may burst causing personal

injury or damage.

• Use only the supplied charger when charging your tool.

The use of any other charger could damage the drill or create a

hazardous condition.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric

plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• An extension cord must have adequate wire size for safety.

An undersized cord will cause a drop in line voltage resulting in loss

of power and overheating. When using more than one extension

to make up the total length, be sure each individual extension

contains at least the minimum wire size. The following table shows

the correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The smaller

the gauge number, the heavier the cord.

Voltage (Volts)

Total length of cord in meters (m)

120–127V 0–7 7–15 15–30 30–50

220–240V 0–15 15–30 30–60 60–100

Rated Ampere

range

Minimal cross-sectional area of the

cord in meters (mm

)

0–6A 1.0 1.5 1.5 2.5

6–10A 1.0 1.5 2.5 4.0

10–12A 1.5 1.5 2.5 4.0

12–16A 2.5 4.0 Not Recommended

• Do not operate the charger with a damaged cord or plug.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. There are no

customer serviceable parts inside.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the batteries will not reduce this risk..

• Use only one charger when charging.

• The charger is designed to operate on standard household

electrical power. Do not attempt to use it on any other

voltage. This does not apply to the vehicular charger.

• DO NOT incinerate the tool or batteries even if they are

severely damaged or completely worn out. The batteries can

explode in a fire.

• Do not incinerate the batteries. They can explode in a fire.

A small leakage of liquid from the battery cells may occur under

extreme usage, charging or temperature conditions. This does

not indicate a failure. However, if the outer seal is broken and this

leakage gets on your skin:

English

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean

water for a minimum of 10 minutes and seek immediate medical

attention. MEDICAL NOTE: The liquid is a 25-35% solution of

potassium hydroxide.

Charging Procedure (Fig. 1)

WARNING: The batteries in your tool are not fully charged at the

factory. Before attempting to charge them, thoroughly read all of the

safety instructions.

WARNING: When disconnecting the tool

FIG. 1

from the charger, be sure to unplug the

charger from the outlet first then disconnect

the charger cord from the tool. Do not use the

tool while it is connected to the charger.

To charge your screwdriver, follow the steps

below.

1. Plug the output cord of the charger into

the socket (G) in the bottom half of the

screwdriver handle as shown in Figure 1.

2. Plug the charger into an appropriate

outlet.

3. Let the tool charge initially for 9 hours.

After the initial charge, under normal

usage, your tool should be fully charged

in 3 to 6 hours.

Important Charging Notes

1. After normal usage, your tool should be fully charged in 3 to 6

hours. If the batteries are run down completely, it may take up

to 6 hours to become fully charged. Your tool was sent from the

factory in an uncharged condition. Before attempting to use it, it

must be charged for at least 9 hours.

2. DO NOT charge the batteries in an air temperature below 40°F

(4.5 °C), or above 105 °F (40.5°C). This is important and will

prevent serious damage to the batteries. Longest life and best

performance can be obtained if the batteries are charged when

the air temperature is 75 °F (24 °C).

3. The charger may hum and become warm to the touch while

charging. This is a normal condition, and does not indicate a

problem.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move the charger and tool to a location where the surrounding

air temperature is approximately 40 °F – 105 °F (4.5° –

40.5°C).;

d. If charging problems persist, take the tool and charger to your

local service center.

5. The tool should be recharged when it fails to produce sufficient

power on jobs which were easily done previously. DO NOT

CONTINUE using product with its batteries in a depleted

condition.

6. To prolong battery life, avoid leaving on charge for extended

periods of time (over 30 days without use). Although overcharging

is not a safety concern, it can significantly reduce overall battery

life.

7. The batteries will reach optimum performance after being cycled

5 times during normal usage. There is no need to run the batteries

down completely before recharging. Normal usage is the best

method of discharging and recharging the batteries.

English

Safety Warnings and Instructions: Drilling

WARNING: Tool may stall (if overloaded or improperly used)

causing a twist. Always expect the stall. Grip the drill firmly to control

the twisting action and prevent loss of control which could cause

personal injury. If a stall does occur, release the trigger immediately

and determine the reason for the stall before restarting.

• Hold tool firmly to control its twisting action.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

DESCRIPTION (FIG. 2)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

FIG. 2

A. Quick release collar

B. Torque control collar

C. LED Light

D. Two speed switch

E. Forward / reverse switch

F. Release button

G. Charging port

OPERATION

WARNING: Always observe the safety instructions and applicable

regulations.

Inserting an Accessory (Fig. 2, 3)

1. Hold the screwdriver upright as shown in

FIG. 3

Figure 3 and pull down on the quick

release collar (A).

2. Insert a hex shank accessory into the

holder.

3. Release the quick release collar.

NOTE: If bit does not fit into spindle,

rotate the bit and reinsert it.

Removing an Accessory

(Fig. 2, 3)

1. Hold the screwdriver upright as shown in Figure 3 and pull down

on the quick release collar (A).

2. Pull accessory straight out.

Switch (Fig. 2)

To turn the tool ON in a forward direction, press the top section of

the rocker switch (E) and the tool will run. Release pressure from the

switch and the tool will stop.

To operate in reverse, press the bottom section of the rocker switch.

Without depressing the rocker switch the tool is locked and will act

as any conventional, non-powered screwdriver.

English

Angling the Screwdriver (Fig. 2, 4)

WARNING:

• To avoid being pinched, hold

FIG. 4

the screwdriver as shown in

Figure 4 when changing

positions.

• Do not use screwdriver as a

pry bar in any position.

• To avoid screwdriver being

turned on accidentally, do not

carry in your pocket.

To convert the tool to an angled screwdriver, push in on the release

button (F) shown in Figure4 and rotate the top portion of the tool until

it locks into one of the remaining two positions.

Torque Control (Fig. 2, 5)

The torque adjustment collar (B) is

FIG. 5

marked with numbers and a drill bit

icon. There are 22 clutch settings in

all. Each click in a clockwise direction

means an increase in the torque

produced.

To set the torque align the desired

setting with the arrow on the tool

housing. The higher the number on

the collar, the higher the torque.

To lock the clutch for heavy fastening

operations, move to the drill bit icon.

If you do not know the appropriate setting to use when tightening a

screw, begin at the lowest torque setting. If the clutch ratchets before

the desired result is achieved, increase the collar setting and continue

tightening the screw. Repeat until you reach the correct setting.

Two Speed Operation (Fig. 2)

The dual range feature of your screwdriver allows you to shift gears

for greater versatility.

To select low speed, (high torque setting), turn tool off and permit to

stop. Push the slide switch (D) located on the top of the tool to the

left. Use low speed for screwdriving operations.

To select the high speed, (low torque setting), turn tool off and permit

to stop. Slide gear shifter fully to the right. Use high speed for drilling

operations.

LED Light (Fig. 2)

To turn the light (C) on, push the slide switch located on the underside

of the screwdriver toward the front of the tool.

Drilling

WARNING: It is important to support work properly and to hold the

drill firmly to prevent loss of control which could cause personal injury

If you have questions on how to operate tool, contact an authorized

service center or other qualified service personnel.

• Use sharp drill bits only.

• Support and secure work properly, as instructed in the safety

Instructions.

• Use appropriate and required safety equipment, as instructed in

the safety instructions.

• Secure and maintain work area, as instructed in the safety

instructions.

• Run the drill very slowly, using light pressure, until the hole is

started enough to keep the drill bit from slipping out of it.

• Apply pressure in a straight line with the bit. Use enough pressure

to keep the bit biting but not so much as to stall the motor or

deflect the bit.

• Hold the tool firmly with two hands to control its twisting

action.

English

• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND

ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN

RESULT.

• Minimize stalling on breakthrough by reducing pressure and

slowly drilling through last part of hole.

• Keep the motor running while pulling the bit out of a drilled hole

This will help reduce jamming.

• Make sure switch turns drill on and off.

Drilling In Wood

Holes in wood can be made with the same twist drill bits used for

metal. These bits should be sharp and should be pulled out frequently

when drilling to clear chips from the flutes.

NOTE: This tool is not recommended for drilling in metal or masonry.

MAINTENANCE

Your DEWALT power tool has been designed to operate over a

long period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and regular

cleaning.

Lubrication

Your power tool requires no additional lubrication.

Cleaning

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the materials used in these parts. Use a cloth dampened only

with water and mild soap. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

Accessories

WARNING: Since accessories, other than those offered by

EWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

EWALT, recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available at extra

cost from your local dealer or authorized service center.

The following accessories should be used only in the sizes specified

below:

BITS - WOOD DRILLING – Up to 1/4" (7 mm).

Repairs

The tool and charger are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by authorized service centers or other qualified service

personnel, always using identical replacement parts.

Protecting the Environment

Separate collection. This product must not be disposed of

with normal household waste.

Should you ﬁnd one day that your D

EWALT product needs

replacement, or if it is of no further use to you, do not dispose of it

with household waste.

Separate collection of used products and packaging allows

materials to be recycled and used again. Re-use of recycled

materials helps prevent environmental pollution and reduces

the demand for raw materials.

Local regulations may provide for separate collection of electrical

products from the household, at municipal waste sites or by the

retailer when you purchase a new product.

English

DEWALT provides a facility for the collection and recycling of DEWALT

products once they have reached the end of their working life. To take

advantage of this service please return your product to any authorized

service center that will collect them on our behalf.

You can check the location of your nearest authorized service center

by contacting your local D

EWALT office. Alternatively, a service center

listing is included in the packaging of this product.

SPECIFICATIONS (CHARGER)

MODEL DCF060-AR DCF060-B2 DCF060-B3

Voltage 220V~ 127 V / 220V~ 120V~

Power 8.8 W 10 W 7.5 W

40 mA 45 mA 63 mA

Frequency 50 Hz 60 Hz 50–60 Hz

Output Voltage 9V~ 300 mA 8V DC 210 mA 9V~ 100 mA

MODEL DCF060-B2C

Voltage 220V~

Power 8.8 W

40 mA

Frequency 50–60 Hz

Output Voltage 9V~ 300 mA

SPECIFICATIONS

(BASE UNIT)

Voltage 6 V DC

No Load Speed 180 / 600

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286

EWALT

The following are trademarks for one or more D

EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the

array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

HECHO EN MÉXICO

FABRICADO NO MÉXICO

MADE IN MEXICO

SOLAMENTE PARA PROPÓSITO DE ARGENTINA:

IMPORTADO POR: BLACK & DECKER ARGENTINA S.A.

PACHECO TRADE CENTER

COLECTORA ESTE DE RUTA PANAMERICANA

KM. 32.0 EL TALAR DE PACHECO

PARTIDO DE TIGRE

BUENOS AIRES (B1618FBQ)

REPÚBLICA DE ARGENTINA

NO. DE IMPORTADOR: 1146/66

TEL. (011) 4726-4400

IMPORTED BY/IMPORTADO POR:

BLACK & DECKER DO BRASIL LTDA.

ROD. BR 050, S/N° - KM 167

DIST. INDUSTRIAL II

UBERABA – MG – CEP: 38064-750

CNPJ: 53.296.273/0001-91

INSC. EST.: 701.948.711.00-98

S.A.C.: 0800-703-4644

SOLAMENTE PARA PROPÓSITO DE MÉXICO:

IMPORTADO POR: D

EWALT INDUSTRIAL TOOL CO. S.A. DE C.V.

AVENIDA ANTONIO DOVALI JAIME, # 70 TORRE B PISO 9

COLONIA LA FE, SANTA FÉ

CÓDIGO POSTAL : 01210

DELEGACIÓN ALVARO OBREGÓN

MÉXICO D.F.

TEL. (52) 555-326-7100

R.F.C.: BDE810626-1W7

MAQUINAS Y HERRAMIENTAS BLACK & DECKER CHILE S.A.

AVDA. EDUARDO FREI M. #6001 EDIFICIO 67

CONCHALI-SANTIAGO

CHILE

FONO: 56-2-26871706

DeWalt DCF060 User manual

Brand: DeWalt

Model: DCF060

Category: Power tools

Type: User manual

Download PDF

report

in other languages

español: DeWalt DCF060 Manual de usuario
português: DeWalt DCF060 Manual do usuário

DeWalt DCF060 User manual

DeWalt DCF060 User manual

in other languages

Related papers

Other documents