ti17103a
Model 24G773
Important Safety Instructions
For complete warnings and safety instructions see RoadLazer
™
RoadPak
™
Line Striper System manual. Save these instructions.
The RoadPak Winch Kit is to be used as a safety
device for the operator to lift the gun arm off the ground
and slowly and safely drive out of the way of traffic to a
safe place where the gun arm can properly be stowed
for transporting. When the operator is not spraying, the
vehicle should not be operated unless the gun arm is
stowed in the proper position. See RoadLazer
™
RoadPak
™
Line Striper System manual.
3A1307A
ENG
Instructions
Winch Kit for RoadLazer
™
RoadPak
™
Line Striping System
2 3A1307A
Winch Kit Installation
1. Assemble adaptor bracket (1) to height adjustment
bracket on both sides. Fasten with bolts (6), wash-
ers (7), and nuts (8). Torque to 28 ft-lb.
2. Use four bolts and lock washers (supplied) to
assemble winch (5) onto winch arm (2).
3. Use bolts, washers, and nuts (supplied) to assemble
cable guide onto winch arm bracket (3).
4. Slide winch arm bracket (3) into winch arm (2) and
secure into place by tightening extension clamp (15)
and inserting the safety pin.
5. Insert winch assembly into one of the adapter brack-
ets (1) and secure with pin (9).
6. Install winch switch (20) and connector bracket (17)
next to the battery on the RoadPak frame. Fasten
with screws (16).
7. Pull the wires of the winch control connector (19)
through the hole of the connector bracket and fasten
the connector to the bracket with screws (18).
ti17104a
8
7
7
6
1
ti17105a
5
2
ti17107a
3
ti17106a
3
2
15
ti17108a
1
9
ti17109a
20
17
16
ti17110a
19
18
3A1307A 3
8. Connect blue and yellow cables (21) from the winch
terminals to blue and yellow color-coded terminals
on winch switch terminal.
9. Disconnect ground terminal on battery. Connect red
and black cables (21) to red and black color-coded
winch switch terminals. Attach the red cable from
the winch control connector and power cable from
the winch switch to the positive terminal on the bat-
tery. Then connect the black cable to the ground ter-
minal on the battery. See Wiring Diagram, page 4.
10. Connect the green plugs from the winch control con-
nector and the winch switch as showed in Wiring
Diagram, page 4.
11. Plug in winch controller (19) to the connector and
route to the cab of the vehicle. Properly protect and
secure all wires to keep from damaging them during
every day use.
12. Adjust the winch arm (3) so it is in line with the lifting
point on the gun arm. Ensure the winch arm is
secured by pinning it and tightening the extension
clamp (15).
13. Use the buttons on the controller to lower the winch.
Connect the winch hook (22) to the lifting point on
the gun arm.
14. When transporting the RoadPak system, the gun
arm must be properly stowed (see manual 3A1214)
and the winch arm must be adjusted to fit within the
width of the vehicle.
ti17111a
21
ti17112a
ti17114a
22
Wiring Diagram
4 3A1307A
Wiring Diagram
ti17113a
Green
Green
Black
Black
Yellow
Blue
Black
Red
+
-
Parts List
3A1307A 5
Parts List
12
7
2
3
5
9
11
10
14
1414
14
14
14
13
15
6
7
8
16
18
1
17
21
20
1919
22
23
ti17115a
Ref. Part Description Qty.
1 16G688 BRACKET, adapter, winch, painted 2
2 24G839 ARM, winch, painted 1
3 24G841 BRACKET, arm, winch, painted 1
5 16G458 WINCH, RoadLazer 1
6 101147 SCREW, cap, hex HD 4
7 109570 WASHER, plain 8
8 801020 NUT, lock, hex 4
9 115473 PIN, hitch 2
10 186812 CHAIN, ground 3.5 HP 2
11 M71635 CLAMP, hose 2
12 100678 SCREW, cap hex HD 1
13 111040 NUT, lock, insert, nylock, 5/16 1
14 100023 WASHER, flat 6
15 238813 CLAMP, extension 1
16 107439 SCREW, mach, hex HD 4
17 16H234 BRACKET, mtg., connector, winch
ctrl
1
18 117501 SCREW, mach, slot hex wash HD 2
19 16H069 SWITCH, corded remote/plug in 1
20 16F346 SWITCH, winch, contactor 1
21 16H070 WIRE, assemblies, battery/winch 1
22 16H068 CONNECTOR, 1-3/8 in. eye dia.,
carbiner
1
23 16H067 CABLE, 3/16 in. dia., blue 1
Ref. Part Description Qty.
Parts List
6 3A1307A
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A1307
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2010, Graco Inc. is registered to ISO 9001
www.graco.com
02/2011
/
