Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
REV 14g
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright
©
2007 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Page 2Item 96136
For technical questions, please call 1-888-866-5797.
SPECIFICATIONS
Display/Electronic Circuit Board Housing 1″ X 1-7/8″ (Digital)
On/Off Type Push Button
Unit Of Measure And Increments
Feet, 1″ to 9999 Feet 11 Inch (6 digits)
Meters, 1 CM to 9999.99 Meters
Power Source 2 - AAA, 1.5V Batteries (not included)
Measurement Clear Device Clear/Hold Button
Number Of Storing Values 2 with Push Button Selector
Handle Length
14-1/4″ to 34″ (Telescopic Adjustment)
Wheel Size 5-5/8″ Diameter
Save This Manual
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the inside
of the front cover. Write the product’s serial number in the back of the manual near the
assembly diagram, or write month and year of purchase if product has no number. Keep
this manual and invoice in a safe and dry place for future reference.
GENERAL AND SPECIFIC SAFETY RULES
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result in serious
injury.
SAVE THESE INSTRUCTIONS
1. WARNING: To prevent leakage and/or explosion, position batteries in proper
polarity and do not install batteries of different types, charge levels or capacities
together.
2. Wear ANSI-approved safety goggles during use of this Digital Measure Wheel.
3. Keep this Measure Wheel out of the reach of children.
4. This Measure Wheel is for estimates only.
5. Do not mix old with new batteries.
6. Maintain labels and nameplates on the tool. These carry important information.
If unreadable or missing, contact Harbor Freight Tools for a replacement.
Page 3Item 96136
For technical questions, please call 1-888-866-5797.
UNPACKING
When unpacking, check to make sure that the item is intact and undamaged. If any
parts are missing or broken, please call Harbor Freight Tools at the number shown on
the cover of this manual as soon as possible.
ASSEMBLY INSTRUCTIONS
Note: This Digital Measure Wheel comes completely assembled. For additional information
regarding the parts listed in the following pages, refer to the Assembly Diagram on
page 6.
OPERATION INSTRUCTIONS
Accuracy can vary as much as 1″ in 50 feet. Because the wheel rolls on different
surfaces, both smooth and bumpy, the Measuring Wheel cannot be relied on to provide
precise measurements.
1. Before using this Digital Measure Wheel be sure the batteries are properly installed.
2. Turn on the Measure Wheel by pushing the ON/OFF Button located on the Display
Housing (23). Clear the Display Window (13) by pushing the Clear Button also located
on the Display Housing (23).
3. Four function buttons are located above the Display Window (13). From left to right
they are the:
a. On/Off Button. This is used to activate or de-activate the Measure Wheel.
b. Feet/Meter Button. Used to change from Meters to measuring in feet.
c. Hold/Clear Button. Press and release this Button if you want to store measurement
history, or press and HOLD this Button down to clear all measurements.
d. NO1/NO2 Button. Use this if you wish to change to another Display. You can
switch back and forth from one measurement to another.
4. Extend the Handle (1) by twisting either of the Handle Locks, (3) or (9) while holding
any of the three Shafts, Upper (2), Middle (7) or Lower (12) and Pulling. To collapse
the Handle (1), simply reverse the procedure. Be sure to retighten the Locked Pieces
before using or storing.
5. Clear any information from the Display Window (13) by pushing the Clear Button.
Place the Wheel (24) at the point where you wish to measure from, then roll the
Measure Wheel in the direction you wish to measure. When you stop, read the bright
green numbers displayed on the black background in the Display Window (13). Then
either store the information (see (3c) above), or clear the information (see (3c) above).
6. Change the batteries by removing the Battery Cover (21), lifting out the old batteries,
and replacing them with fresh new batteries. Replace the Battery Cover (21). Be
sure to properly dispose of the old batteries in normal trash. NEVER incinerate them.
7. Turn off the Digital Measure Wheel after using. If it will be stored for an extended
period, remove the batteries.
Page 4Item 96136
For technical questions, please call 1-888-866-5797.
INSPECTION, MAINTENANCE, AND CLEANING
1. WARNING! Make sure the Switch of the Measure Wheel is in its “OFF” position
before performing any inspection, maintenance, or cleaning procedures.
2. BEFORE EACH USE, inspect the general condition of the tool. Check for loose
screws, cracked or broken parts, and any other condition that may affect its safe
operation. If anything abnormal is noticed have the problem corrected before further
use. Do not use damaged equipment.
TROUBLESHOOTING
Problem Possible Causes Probable Solutions
Display will not
show in Display
Window
1. Batteries are bad or installed incorrectly.
2. On/Off Button not in ON position.
1. Check Batteries and replace them
if they are bad. Pull them out of the
Battery compartment and check for
correct polarity alignment.
2. Check the On/Off Button
Page 5Item 96136
For technical questions, please call 1-888-866-5797.
PARTS LIST
Part Description Q’ty
1 Handle 1
2 Upper Shaft 1
3 Handle Lock “A” 1
4 Middle Lock Head 1
5 Big Pipe Inner Sleeve 1
6 Middle Pipe Outer Sleeve 1
7 Middle Shaft 1
8 Middle Pipe Inner Sleeve 1
9 Handle Lock “B” 1
10 Small Lock Head 1
11 Small Pipe Outer Sleeve 1
12 Lower Shaft 1
13 Display Window 1
14 Bearing 2
15 Negative Battery Contact 1
Part Description Q’ty
16 Positive Battery Contact 1
17 Middle Battery Contact 1
18 Side Cover 1
19 Buttons Strip 1
20 Display and Circuit Board 1
21 Battery Cover 1
22 Middle Axis 1
23 Display Housing 1
24 Wheel 1
25 Wheel Axel Cover 1
27 Screw for Slide Cover 4
28 Axle Screw 1
29 Display Housing Lock Screw 1
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND
ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Page 6Item 96136
For technical questions, please call 1-888-866-5797.
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
ASSEMBLY DIAGRAM
/
