SAVE FOR FUTURE USE
1
7301915-100
Product names listed herein are trademarks of AS Americas Inc.
© AS Americas Inc. 2012
Putty Knife Sealant
Tape Measure
Regular Screwdriver
Adjustable Wrench
Carpenters Level
Flush Valve
RECOMMENDED TOOLS AND MATERIALS
Pictures may not exactly define contour of china
Model 3541, 3543
MODEL 3541MODEL 3543
COLORADO 15" AND 17" FLUSH VALVE
FLOOR MOUNTED TOILETS
NOTE: For proper operation product requires a minimum of 30 psi working line pressure
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. (Certain installations may
require professional help.) Also be sure your installation conforms to local codes.
!
INSTALLATION
INSTRUCTIONS
FINISHED WALL
FINISHED
FLOOR
17-1/4"
(438mm)
*
14"
(356mm)
14-1/2"
(368mm)
C/L OF
OUTLET
18-1/2"
(470mm)
4-3/4"
(121mm)
*
1-1/2" (38mm)
SPUD CONNECTION
24-1/16"
(612mm)
3-1/2"-5-1/2"
(89mm-140mm)
28-1/16"-30-1/16"
(713mm-746mm)
10"-12"
(254mm-305mm)
*
VARIABLE-CHECK WITH MANUFACTURER
OF FLUSHVALVE FOR PROPER ROUGH-IN
DIMENSIONS.
FINISHED
FLOOR
15"
(381mm)
*
C/L OF
OUTLET
14"
(356mm)
18-1/2"
(470mm)
*
1" (25mm)
I.P.S. SUPPLY
1" (25mm)
I.P.S. SUPPLY
*
1-1/2" (38mm)
SPUD CONNECTION
3-3/4"-5-3/4"
(95mm-146mm)
27-5/8"-29-5/8"
(702mm-752mm)
6-1/4"
(159mm)
10"-12"
(254mm-305mm)
*
VARIABLE-CHECK WITH MANUFACTURER
OF FLUSHVALVE FOR PROPER ROUGH-IN
DIMENSIONS.
3/16"-2-3/16"
(5mm-56mm)
FINISHED WALL
CAUTION: PRODUCT IS FRAGILE. TWO PEOPLE ARE RECOMMENDED FOR HANDLING TO
AVOID BREAKAGE AND POSSIBLE INJURY!
7301915-100
4
5
- 2 -
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts
project through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked
"THIS SIDE UP" must face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
FLANGE
INSTALL TOILET
a. Position toilet squarely to wall and, with a rocking motion, press bowl
down fully on wax ring and flange. Alternately tighten nuts until toilet is
firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b. Install caps on washers. (If necessary, cut bolt height to size before
installing caps.)
c. Smooth off the bead of sealant around base. Remove excess sealant.
CLOSET FLANGE
CLOSET BOLT
NUT
WASHER
BOLT
CAP
!
2
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90°, and slide
into place 6" (152 mm) apart and parallel to wall.
CLOSET
FLANGE
CLOSET BOLTS
10" - 12"
254mm - 305mm
INSTALL WAX SEAL
Invert toilet on floor (cushion to prevent damage), and install wax
ring evenly around waste flange (horn), with tapered end of ring
facing toilet. Apply a thin bead of sealant around toilet base.
WAX RING
SEALANT
3
7301463-100 Rev. A
THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.
AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in materials or
workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase will be
required—save sales receipt.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local
building or plumbing contractor to insure local code compliance before installation.
This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or
other damages; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped
by American Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or installation. IN NO EVENT
WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT LIMITED TO,
TILES, MARBLE, ETC. American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or
exchange of a defective product, all of which are expressly excluded from this limited warranty. This limited warranty does not cover any liability for consequential or
incidental damages, all of which are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion
may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this limited
warranty does not affect such statutory rights.
In the United States:
American Standard Brands
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Customer Care
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: (800) 442-1902
www.americanstandard.com
In Canada:
AS Canada, ULC
5900 Avebury Rd.
Mississauga, Ontario
Canada L5R 3M3
Toll Free: (800) 387-0369
www.americanstandard.ca
In Mexico:
American Standard B&K Mexico
S. de R.L. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Toll Free: 01-800-839-1200
www.americanstandard.com.mx
/