Polar Refrigeration G593 User manual

Brand: Polar Refrigeration

Model: G593

Category: Barbecues & grills

Type: User manual

This manual is also suitable for

Stainless Steel Cabinet Refrigerators/Freezers

Models:

G590/G591/G592/G593/G594/G595/U629/U630

Table Of Contents

Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Pack Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Removing the Compressor Safety Band (G592/G593/G594/G595/U629/U630 only) . . . . . . 1

Fitting the Waste Water Tray (G592/G593/G594/G595/U629/U630 only) . . . . . . . . . . . . . . 1

Fitting the Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Storing Food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Turn On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Lock/Unlock the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Enter the Parameter Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Manual Defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Lock/Unlock the Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cleaning, Care & Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cleaning the Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Electrical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety Tips

• Position on a flat, stable surface.

• A service agent/qualified technician should carry out installation and any

repairs if required. Do not remove any components or service panels on

this product.

• Consult Local and National Standards to comply with the following:

• Health and Safety at Work Legislation

• BS EN Codes of Practice

• Fire Precautions

• IEE Wiring Regulations

• Building Regulations

• DO NOT use jet/pressure washers to clean the appliance.

• DO NOT use the appliance outside.

• DO NOT use this appliance to store medical supplies.

• DO NOT use electrical appliances inside the appliance (e.g. heaters, ice-

cream makers etc.)

• DO NOT stand or support yourself on the base, drawers or doors.

• DO NOT allow oil or fat to come into contact with the plastic

components or door seal. Clean immediately if contact occurs.

• Bottles that contain a high percentage of alcohol must be sealed and

placed vertically in the refrigerator.

• Always carry, store and handle the appliance in a vertical position and

move by holding the base of the appliance.

• Always switch off and disconnect the power supply to the unit before

cleaning.

• Keep all packaging away from children. Dispose of the packaging in

accordance with the regulations of local authorities.

• If the power cord is damaged, it must be replaced by a POLAR agent or

a recommended qualified technician in order to avoid a hazard.

Product Description

G590 - 400 litre Single Door Stainless Steel Refrigerator

G591 - 400 litre Single Door Stainless Steel Freezer

G592 - 600 litre Single Door Stainless Steel Refrigerator

G593 - 600 litre Single Door Stainless Steel Freezer

G594 - 1200 litre Double Door Stainless Steel Refrigerator

G595 - 1200 litre Double Door Stainless Steel Freezer

U629 - 600 litre Single Glass Door Refrigerator

U630 - 1200 litre Double Glass Door Refrigerator

Introduction

Please take a few moments to carefully read through this manual. Correct

maintenance and operation of this machine will provide the best possible

performance from your POLAR product.

Pack Contents

The following is included:

POLAR prides itself on quality and service, ensuring that at the time of

packaging the contents are supplied fully functional and free of damage.

Should you find any damage as a result of transit, please contact your POLAR

dealer immediately.

Installation

1. Remove the appliance from the packaging. Make sure that all protective

plastic film and coatings are thoroughly removed from all surfaces.

2. Maintain a distance of 20cm (7 inches) between the unit and walls or

other objects for ventilation. Increase this distance if the obstacle is a

heat source.

3. Level the appliance by adjusting the screw feet.

Removing the Compressor Safety Band

(G592/G593/G594/G595/U629/U630 only)

The compressor is located on the top of the appliance, and sits on rubber

washers. Under normal operating conditions the compressor is allowed to

vibrate.

To avoid damage through excessive motion during transit, a stainless steel

safety band is placed over the compressor and screwed into the top of the

appliance.

This safety band and the two screws fixing it to the appliance must be

removed before the appliance is turned on.

Fitting the Waste Water Tray

(G592/G593/G594/G595/U629/U630 only)

The waste water tray and supports comes ready to fit to the underside of the

appliance.

1. Carefully tip the appliance to gain access to the underside.

2. Screw the supports into the holes on the underside of the appliance,

using the screws and washers provided.

3. Lower the appliance and slide the tray onto the supports.

Note: If the unit has been stored in a non-vertical position,

stand it in an upright position for approximately 12 hours

before operation.

Note: Before using the appliance for the first time, clean the

internal cabinet and shelves with soapy water.

Compressor

Safety Band

Screws

Compressor

• POLAR Refrigerator or Freezer

•Keys x 2

• Shelf guides x 8 (Single)/

x 16 (Double)

• Shelves x 4 (Single)/

x 8 (Double)

• Instruction manual

• Waste water tray

• Waste water tray supports x 2

•Screws x 6

•Washers x 6

• Spring washers x 6

Fitting the Shelves

1. Place one set of shelf guides on either side of the cabinet at the desired

height.

2. Slide the shelf into place.

3. Repeat for the remaining shelves.

Operation

Storing Food

To get the best results from your POLAR appliance, follow these instructions:

• Only store foodstuffs in the appliance when it has reached the correct

operating temperature.

• Do not place uncovered hot food or liquid inside the appliance.

• Wrap or cover food where possible.

• Do not obstruct the fans inside the appliance.

• Avoid opening the doors for prolonged periods of time.

Turn On

1. Close the door(s) of the appliance.

2. Ensure the power switch is set to [O] and turn on at the socket.

3. Switch on the Power [I]. The current temperature within the appliance

is displayed.

Control Panel

Lock/Unlock the Control Panel

To lock the control panel:

1. Press and hold the UP and DOWN

buttons simultaneously for 10

seconds.

2. Pof flashes on the display and the keyboard is locked.

To unlock the control panel:

1. Press and hold the UP and DOWN

buttons simultaneously for 10

seconds.

2. Pon flashes on the display and the keyboard is unlocked.

Enter the Parameter Menu

1. Unlock the control panel, if locked.

2. Press and hold the SET

button until ‘d1’ flashes on the display.

3. Press the SET

button repeatedly to scroll to the desired parameter

(see below).

Note: Always place one shelf in the lowest available position,

or if that position is higher than 40mm, place the shelf

directly onto the floor of the cabinet without the guides.

This is vital for ensuring correct drainage of condensation.

Note:

If a button is not pressed for 10 seconds while using the

control panel it times out and reverts to standby mode.

When parameters are being set the Setpoint LED will flash on

the display.

Pon

Parameter Name Description Range

d1 Operating temperature Set the operating temperature of the appliance -2°C to 10°C

Temperature

Differential

The Temperature Differential is the allowed temperature difference above and below the

operating temperature before the compressor starts/cuts off

0 to 20°C

Temperature Range

Set the minimum (d3) and maximum (d4) temperatures that the appliance can fluctuate

between

-40°C

d4 95°C

Compressor Activation

Time Intervals

Enter the minimum time interval between the compressor turning off after turning on. 0-999 seconds

Maximum Temperature

Differential Alarm

Set an alarm to sound if the temperature inside the appliance exceeds the set operating

temperature by a specified amount

0°C-50°C

Temperature

Differential Alarm Delay

Set a delay before the temperature differential alarm is triggered 0-99 minutes

Defrost Cycle Time

Intervals

Set the time between each defrost cycle 1-999 hours

Maximum Defrost

Duration

Set the maximum length of the defrost cycle

Note: The defrost duration can be overridden by parameter d10 (below), if the

cut-off temperature is reached before the end of the defrost duration

0-999 minutes

d10

Defrost Cut-off

Temperature

(G591/G593/G595 only) Set the defrost cut-off temperature -45°C to 50°C

d11

Additional Cut-off

Defrost Period

(G591/G593/G595 only) Set an additional amount of defrost time after the defrost cut-off

point has been reached (if required)

0-99 minutes

d12

Delayed Actual

Temperature Display

Set the length of time the inner temperature of the appliance (before defrost started) is

displayed for after a defrost cycle has finished

0-99 minutes

d13

Compressor On/Off

During Defrost

(G591/G593/G595 only) Turn the Compressor On or Off during the defrost cycle On (1) or Off (0)

d14 Evaporator Drying Time

Set the amount of time the compressor remains turned Off after a defrost cycle, reducing the

amount of frost build up

0-99 minutes

Manual Defrost

The appliance will automatically run a defrost cycle every six hours.

To manually defrost the appliance:

1. Press and hold the DEFROST button for 5 seconds.

2. The defrost cycle will start immediately and the Defrost LED illuminates.

The defrost will last a maximum of 30 minutes.

3. Waste water is collected in the waste water tray.

Lock/Unlock the Doors

A lock is fitted to the doors to ensure foodstuffs are kept secure within your

POLAR appliance.

Use the keys provided to lock/unlock the doors.

Cleaning, Care & Maintenance

• Switch off and disconnect from the power supply before cleaning.

• Clean the interior of the appliance as often as possible.

• Do not use abrasive cleaning agents. These can leave harmful residues.

• Clean the door seal with water only.

• Always wipe dry after cleaning.

• Do not allow water used in cleaning to run through the drain hole into

the evaporation pan.

• Take care when cleaning the rear of the appliance. Sharp edges can cut.

• A POLAR agent or qualified technician must carry out repairs if required.

Cleaning the Condenser

Periodically cleaning the condenser can extend the life of the appliance.

POLAR recommend that a POLAR agent or qualified technician clean the

condenser.

Troubleshooting

If your POLAR appliance develops a fault, please check the following table

before making a call to the Helpline.

Parameter Name Description Range

=19 Temperature Offset

Should there be any variance between measured and actual temperature, the measured

temperature can be offset to compensate

-20°C to 20°C

=22 Unit of Measurement Set whether the temperature is displayed in Centigrade or Fahrenheit Centigrade (0) or Fahrenheit (1)

=23

Compressor Operation

During Probe Failure

Set whether the compressor runs or remains Off during a temperature probe failure

Compressor runs (1)

Remains Off until fault fixed (0)

Runs intermittently with

parameters =24 and =25 (2)

=24

Compressor ‘On’

Duration

Set the length of time the compressor runs during a temperature probe failure 1-99 minutes

=25

Compressor ‘Off’

Duration

Set the length of time the compressor remains Off during a temperature probe failure 1-99 minutes

=34

Initial Defrost After

Startup

(G591/G593/G595 only) Set whether the appliance starts a defrost cycle 10 minutes after

startup or after the time programmed in parameter d8 (Defrost Cycle Time Intervals)

Begins 10 minutes after startup

(0) or when programmed (1)

=38

Minimum Temperature

Alarm

Set the display to flash should the inner temperature of the appliance drop beyond a specified

point from the programmed operating temperature

1°C to 50°C

Note: The cycle starts from the time the appliance is initially

powered up.

Note: Starting a manual defrost also resets the automatic

defrost timer.

The next automatic defrost will start six hours after the

manual defrost has finished.

Fault Probable Cause Action

The appliance

is not working

The unit is not switched on Check the unit is

plugged in correctly

and switched on

Plug and lead are damaged Call POLAR agent or

qualified Technician

Fuse in the plug has blown Replace the fuse

Power supply Check power supply

Internal wiring fault Call POLAR agent or

qualified Technician

The appliance

turns on, but

the

temperature is

too high/low

Too much ice on the condenser Defrost the appliance

Condenser blocked with dust Call POLAR agent or

qualified Technician

Doors are not shut properly Check doors are shut

and seals are not

damaged

Appliance is located near a heat

source or air flow to the

condenser is being interrupted

Move the refrigerator to

a more suitable location

Ambient temperature is too

high

Increase ventilation or

move appliance to a

cooler position

Unsuitable foodstuffs are being

stored in the appliance

Remove any excessive

hot foodstuffs or

blockages to the fan

Appliance is overloaded Reduce the amount of

food stored in the

appliance

The appliance

is leaking water

The appliance is not properly

levelled

Adjust the screw feet to

level the appliance

The discharge outlet is blocked Clear the discharge

outlet

Movement of water to the drain

is obstructed

Clear the floor of the

appliance

The water container is

damaged

Call POLAR agent or

qualified Technician

The drip tray is overflowing Empty the drip tray

The appliance

is unusually

loud

The frame has become loose Check and tighten all

nuts and screws

The appliance has not been

installed in a level or stable

position

Check installation

position and change if

necessary

Error Messages

The following table details the cause and subsequent response of the appliance to errors.

The alarm message will end when the alarm trigger is no longer present, except PF1 and PF2 that require the appliance to be turned Off, then On again.

Technical Specifications

Electrical Wiring

POLAR Refrigerators and Freezers are supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard.

The plug is to be connected to a suitable mains socket.

POLAR Refrigerators and Freezers are wired as follows:

• Live wire (coloured brown) to terminal marked L

• Neutral wire (coloured blue) to terminal marked N

• Earth wire (coloured green/yellow) to terminal marked E

All POLAR Refrigerators and Freezers must be earthed, using a dedicated earthing circuit.

If in doubt consult a qualified electrician.

Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible.

Compliance

BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and

federal authorities.

BUFFALO products have been approved to carry the following symbol:

Error Message

(flashing)

Cause Appliance Response Action

HtA

The inner temperature exceeds

the set maximum temperature

Display flashes

Alternating error message and current temperature

Check Troubleshooting Guide

If problem persists call POLAR agent or