Philips LTC 3963/51 User manual

Brand: Philips

Model: LTC 3963/51

Category: Security access control systems

Type: User manual

PHILIPS LTC3963/51 (E) QR31809

Time-lapse

Video Recorder

LTC 3963/51

Instructions for Use

Eng

PHILIPS LTC3963/51 (E) QR31809

As the colours of the wires in the mains lead of

this apparatus may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows:

– the wire which is coloured green and yellow

must be connected to the terminal in the

plug which is marked with the letter E or by

the earth symbol , or coloured green

or green and yellow.

– the wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

– the wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

WARNING — THIS APPARATUS MUST BE

EARTHED.

ENGLISH

1. Read Instructions — All the safety and operating instructions

should be read before the unit is operated.

2. Retain Instructions — The safety and operating instructions

should be retained for future reference.

3. Heed Warnings — All warnings on the unit and in the operating

instructions should be adhered to.

4. Follow Instructions — All operating and use instructions should

be followed.

5. Cleaning — Unplug the unit from the outlet before cleaning. Do

not use liquid cleaners or aerosol cleaners. Use a damp cloth for

cleaning.

6. Attachments — Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

7. Water and Moisture — Do not use this unit near water – for

example, near a bath tub, wash bowl, kitchen sink, or laundry tub,

in a wet basement, near a swimming pool, in an unprotected out-

door installation, or any area which is classified as a wet location.

8. Accessories — Do not place this unit on an unstable stand, tripod,

bracket, or mount. The unit may fall, causing serious injury to a

person and serious damage to the unit. Use only with a stand, tri-

pod, bracket, or mount recommended by the manufacturer, or

sold with the product. Any mounting of the unit should follow the

manufacturer’s instructions, and should use a mounting access-

ory recommended by the manufacturer.

An appliance and cart combination should be

moved with care. Quick stops, excessive force, and

uneven surfaces may cause the appliance and cart

combination to overturn.

9. Ventilation — Openings in the enclosure, if any, are provided for

ventilation and to ensure reliable operation of the unit and to pro-

tect it from overheating. These openings must not be blocked or

covered. This unit should not be placed in a built-in installation

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

10. Power Sources — This unit should be operated only from the type

of power source indicated on the marking label. If you are not

sure of the type of power supply you plan to use, consult your

appliance dealer or local power company. For units intended to

operate from battery power, or other sources, refer to the

operating instructions.

11. Grounding or Polarization — This unit may be equipped with a

polarized alternating-current line plug (a plug having one blade

wider than the other). This plug will fit into the power outlet only

one way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the plug should

still fail to fit, contact your electrician to replace your obsolete

outlet. Do not defeat the safety purpose of the polarized plug.

Alternately, this unit may be equipped with a 3-wire grounding-

type plug, a plug having a third (grounding) pin. This plug will

only fit into a grounding-type power outlet. This is a safety fea-

ture. If you are unable to insert the plug into the outlet, contact

your electrician to replace your obsolete outlet. Do not defeat the

safety purpose of the grounding-type plug.

12. Power-Cord Protection — Power-supply cords should be routed

so that they are not likely to be walked on or pinched by items

placed upon or against them, paying particular attention to cords

and plugs, convenience receptacles, and the point where they exit

from the appliance.

13. Power Lines — An outdoor system should not be located in the

vicinity of overhead power lines or other electric light or power

circuits, or where it can fall into such power lines or circuits.

When installing an outdoor system, extreme care should be taken

to keep from touching such power lines or circuits as contact with

them might be fatal. U.S.A. models only – refer to the National

Electrical Code Article 820 regarding installation of CATV

systems.

14. Overloading — Do not overload outlets and extension cords as

this can result in a risk of fire or electric shock.

15. Object and Liquid Entry — Never push objects of any kind into

this unit through openings as they may touch dangerous voltage

points or short-out parts that could result in a fire or electric

shock. Never spill liquid of any kind on the unit.

16. Servicing — Do not attempt to service this unit yourself as open-

ing or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service personnel.

17. Damage Requiring Service — Unplug the unit from the outlet and

refer servicing to qualified service personnel under the following

conditions.

a. When the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the unit.

c. If the unit has been exposed to rain or water.

d. If the unit does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions, as an improper adjustment of other

controls may result in damage and will often require extensive

work by a qualified technician to restore the unit to its normal

operation.

e. If the unit has been dropped or the cabinet has been damaged.

f. When the unit exhibits a distinct change in performance – this

indicates a need for service.

18. Replacement Parts — When replacement parts are required, be

sure the service technician has used replacement parts specified

by the manufacturer or have the same characteristics as the orig-

inal part. Unauthorized substitutions may result in fire, electric

shock or other hazards.

19. Safety Check — Upon completion of any service or repairs to this

unit, ask the service technician to perform safety checks to deter-

mine that the unit is in proper operating condition.

20. Coax Grounding — If an outside cable system is connected to the

unit, be sure the cable system is grounded. U.S.A. models only –

Section 810 of the National Electrical Code, ANSI/NFPA No. 70-

1981, provides information with respect to proper grounding of

the mount and supporting structure, grounding of the coax to a

discharge unit, size of grounding conductors, location of

discharge unit, connection to grounding electrodes, and

requirements for the grounding electrode.

21. Lightning — For added protection of this unit during a lightning

storm, or when it is left unattended and unused for long periods

of time, unplug it from the wall outlet and disconnect the cable

system. This will prevent damage to the unit due to lightning and

power-line surges.

IMPORTANT SAFEGUARDS

PHILIPS LTC3963/51 (E) QR31809

SAFETY PRECAUTIONS

RISK OF ELECTRIC

SHOCK. DO NOT OPEN!

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT OPEN COVERS. NO USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This label may appear on the bottom of the unit due

to space limitations.

WARNING: Electrostatic-sensitive device. Use

proper CMOS/MOSFET handling precautions to

avoid electrostatic discharge.

NOTE: Grounded wrist straps must be worn and

proper ESD safety precautions observed when

handling the electrostatic-sensitive printed circuit

boards.

The lightning flash with an arrowhead sym-

bol, within an equilateral triangle, is intended

to alert the user to the presence of uninsu-

lated “dangerous voltage” within the prod-

uct’s enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to pres-

ence of important operating and mainten-

ance (servicing) instructions in the literature

accompanying the appliance.

Attention: Installation should be performed

by qualified service personnel only in ac-

cordance with the National Electrical Code or

applicable local codes.

Power Disconnect: Units with or without

ON-OFF switches have power supplied to the

unit whenever the power cord is inserted

into the power source; however, the unit is

operational only when the ON-OFF switch is

in the ON position. The power cord is the

main power disconnect for all units.

External Power Supplies

Use Only the Recommended Power Supplies.

Power supplies must comply with the

requirements of the latest version of IEC

65/VDE 0860. Substitutions may damage the

unit or cause a fire or shock hazard.

220-240 V, 50 Hz power cords, input and out-

put, must comply with the latest versions of

IEC Publication 227 or IEC Publication 245.

220-240 V, 50 Hz Power Cords

WARNING

To prevent fire or shock hazard, do not expose

units not specifically designed for outdoor use

to rain or moisture.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE

DEVICES

1 UNPACKING

Unpack carefully. This is electronic equipment and

should be handled carefully.

Check to ensure that the following items are in-

cluded:

• Model number of unit.

If an item appears to have been damaged in ship-

ment, replace it properly in its carton and notify the

shipper. If any items are missing, notify your Philips

Communication & Security Systems Inc. Sales

Representative or Customer Service.

The shipping carton is the safest container in which

the unit may be transported. Save it for possible

future use.

2 SERVICE

If the unit ever needs repair service, the customer

should contact the nearest Philips Communication

& Security Systems Inc. Service Center for return

authorization and shipping instructions.

Service Centers

U.S.A. & Canada: 800-366-2283

Mexico & Central America: 52-5-564-2726

Europe & Middle East: 44-1932-765666

South America: 54-1-956-0837

Australia: 61-2-888-9000

New Zealand: 64-4-237-7297

3 DESCRIPTION

4 INSTALLATION

PHILIPS LTC3963/51 (E) QR31809

FEATURES CONTENTS

Recording

• HD (High Density) Mode Recording Only

• Eight Touch-Selectable Recording Speeds

• Automatic “Alarm-Command” Speed Up

• Recording Check

• One Shot Recording

• On-Screen and On-Tape Time/Date Information

• 7-Day Programmable On/Off Timer

• “Alarm On” Output

• Usable Audio at 09 and 27 Hour Speeds

• RS-232C Interface Connector

Playback

• Time-of-Alarm Memory and Alarm Index Search

• High Speed Visual Search

• Seven Playback Speeds

• Still Field, Field-Advance, Field-Reverse and

Reverse Playback

Security

• About 720 Hours Memory Protection

• Electronic Security Lockout

Note: This recorder has a rechargeable battery

to maintain display functions and recording

mode within 720 hours in the event of power

loss. When the recorder is received, the unit

must be connected to power source for 48

hours to assure the battery has been ad-

equately charged.

IMPORTANT SAFEGUARDS......................................1

SAFETY PRECAUTIONS.............................................2

PRECAUTIONS............................................................4

CONTROLS AND FUNCTIONS ..................................5

INSTALLATION ...........................................................9

EXTERNAL CONNECTIONS.....................................10

CASSETTE TAPES ....................................................12

SETUP........................................................................13

SETTING THE TIME AND DATE..........................14

SETTING [OPTIONS] ITEMS................................15

SUMMER TIME FUNCTION.................................15

SETTING THE TIMER ...........................................15

SETTING THE VCR FUNCTIONS.........................17

SETTING THE BUZZER.........................................18

SETTING THE ALARM..........................................19

ALARM MEMORY RECALL AND RESET ............20

OPERATION...............................................................21

TAPE RECORDING................................................21

REC CHECK............................................................21

AUTO REC CHECK................................................21

ONE SHOT RECORDING......................................21

TIMER RECORDING..............................................21

TAPE RECYCLE .....................................................21

ALARM RECORDING............................................22

MASTER SYSTEM RESET....................................22

PLAYBACK.............................................................22

STILL PLAYBACK..................................................22

V.LOCK ADJUST...................................................22

PLAYBACK IN THE FIELD ADVANCE/

REVERSE MODES ............................................23

VISUAL SEARCH (High Speed Scan) .................23

ALARM INDEX SEARCH ......................................23

TO SECURE THE VCR ..........................................23

OPERATING THE VCR FROM A PERSONAL

COMPUTER...........................................................24

PROBLEM GUIDE......................................................28

SPECIFICATIONS ......................................................29

Touches the video head in the active position

Cylinder

Cleaning roller in the stand-by position

(Special material)

Tape guide

Tape

Video head

Auto Head Cleaning System

This system cleans the video heads automatically when a cassette is inserted and ejected or the tape is

rewound in the recycle recording mode, to prevent dirt from accumulating on the heads.

PHILIPS LTC3963/51 (E) QR31809

PRECAUTIONS

Safety

• Should any solid object or liquid fall into the cabi-

net, turn off the unit and have it checked by quali-

fied personnel before operating it any further.

• To disconnect the mains lead, pull it out by the

plug. Never pull the lead itself.

Installation

• Choose a location in which air can pass through

the ventilation holes in the bottom, top and back

of the unit to prevent it from overheating.

• Do not install the unit near heat sources such as

radiators or air ducts or in a place subject to direct

sunlight, excessive dust, mechanical vibrations or

shock.

• Do not place heavy objects or heat-generating

objects on the VCR, or the cabinet could be dam-

aged or the temperature inside the VCR could

rise, which could cause a fault.

• Never bring a magnet or magnetized object near

the VCR because it will adversely affect the per-

formance of the VCR.

• Do not install the unit in an inclined position.

The unit is designed for operation in a horizontal

position.

Operation

• Condensation

If you pour a cold liquid into a glass, water vapor

in the air will condense on the surface of the

glass.

This is the condensation of moisture.

Condensation on the head drum, one of the most

crucial parts of the VCR, will cause damage to the

tape. The VCR should not be operated for at least

2 hours after being moved from a cold to a hot

environment to avoid condensation from occur-

ring on the head drum.

Cleaning

• Be careful; when the surface of the case is wiped

with a volatile agent such as benzine, alcohol,

thinner, etc., or a chemically processed cloth, the

surface finish may be degraded or its coating may

peel off.

Repacking

• It is wise to save the packing materials and box in

case you ever need to ship or store your unit.

PHILIPS LTC3963/51 (E) QR31809

[FRONT]

4 5 6 7 8 9 10 11 12 13 14 15 16 18 1917

DISPLAY (See page 7)

CONTROLS AND FUNCTIONS

1. RESET BUTTONS

Press these buttons at the same time to clear all

(microprocessor) functions.

Press the “S” button to reset the system. (This does

not erase the stored information.)

2. CASSETTE COMPARTMENT

3. SHARPNESS CONTROL

Adjust the picture quality to hard or soft during play-

back.

4. TRACKING CONTROL

Adjust to optimize the picture quality during playback

at the 09 and 27 hour speeds.

5. SLOW TRACKING CONTROL

Adjust to optimize the picture quality in the SLOW

PLAY mode, e.g. speeds over 48 hours.

6. V. LOCK CONTROL

Reduces vertical jitter in the still play mode.

7. PROGRAM BUTTON

Press to select one of the six programmable func-

tions.

8. START/STOP BUTTON

Press to start or stop the programming of a program-

mable function. (Press once to start the programming

sequence and a second time to stop (end) it.)

9. SET BUTTON

Press to select the specific value which is to be

changed with the UP/DOWN buttons.

10. DOWN BUTTON

Press to decrement, change or reverse to the

previous/lower value.

11. UP BUTTON

Press to increase, change or advance to the next

higher value.

12. V-POS (VERTICAL POSITION) BUTTON

Press repeatedly to control the vertical position of the

programmable display on the monitor.

13. H-POS (HORIZONTAL POSITION) BUTTON

Press repeatedly to control the horizontal position of

the programmable display on the monitor.

14. ALARM INDEX BUTTON

Press this button to cause the INDEX indicator to light,

and set the VCR to the visual search mode (press

F.FWD or REWIND during playback mode) in this

state; the start of the alarm recorded can be located.

15. ALARM RESET BUTTON

Press to clear POWER LOSS information. When this

button is pressed, the alarm memory is cleared.

16. COUNTER RESET BUTTON

Press to clear the digital counter to “00000”.

17. REC/PLAY HOURS BUTTONS

▲ (UP): Press to increase hours to the next

higher value.

▼ (DOWN): Press to decrease hours to the next

lower value. The tape speed will be

indicated as part of the monitor display.

18. TIMER BUTTON

Press after programming the TIMER for automatic

TIMER recording. See page 15 for TIMER program-

ming.

19. SUMMER TIME BUTTON

Press to set the summer time. See “SUMMER TIME

FUNCTION” on page 15 for details.

PHILIPS LTC3963/51 (E) QR31809

25 26

21 22

20. EJECT BUTTON

Press to remove the cassette. The EJECT button will

not operate in the RECORD mode.

21. FIELD REVERSE BUTTON

Press to reverse the tape by one field in the STILL

playback mode.

22. STILL BUTTON

Press to momentarily stop tape motion in the play

mode. The STILL function allows close inspection of

individual scenes. See the description of STILL play-

back on page 22.

23. FIELD ADVANCE BUTTON

Press to advance the tape one field in the STILL play-

back mode.

24. RECORD BUTTON

Press to start recording.

25. STOP BUTTON

Press to stop the tape. The STOP button must be

pressed to end the RECORD and PLAY mode.

26. PLAY BUTTON

Press to play recorded material in the forward direc-

tion. Pressing this during recording makes it possible

to check recordings.

27. REVERSE PLAY BUTTON

Press to play recorded material at the 09, 72, 120,

168, 240 speed in the reverse direction during the

PLAY mode.

28. FAST FORWARD/VISUAL SEARCH BUTTON

Press to activate fast forward.

Press this button during playback and a forward play-

back picture at high speed can be seen.

29. REWIND/VISUAL SEARCH BUTTON

Press to start rewind.

Press this button during playback and a reverse play-

back picture at high speed can be seen.

PHILIPS LTC3963/51 (E) QR31809

37 39 4038

TAB

TAPE END

TIMER

REC

ALARM

LOCK

INDEX

31 32 33 34 3635

[DISPLAY]

SPEED

CONTROLS AND FUNCTIONS (Continued)

30. TAPE-IN INDICATOR

Lights when a cassette is in the compartment.

31. TAB INDICATOR

Lights when a cassette without its safety tab is loaded.

32. ALARM INDICATOR

ALARM appears during alarm recording.

ALARM flashes when alarm recording ends.

33. TAPE END INDICATOR

Lights when the tape reaches the end during record-

ing.

Note: “TAPE END” is not displayed when you have

selected REWIND, RE-REC in the “RECYCLE FUNC-

TIONS” menu in the alarm display or you have

selected REWIND, STOP IF ALARM but an alarm

recording has not been made.

34. A INDICATOR

Lights when no video signal is input. Video signal

input will turn this indicator off automatically.

35. TIMER INDICATOR

This is lit during timer recording or TIMER stand-by

mode.

The indicator flashes in the following cases.

• A cassette is not loaded.

• A cassette without its safety tab is loaded.

• The timer has not been programmed.

36. LOCK INDICATOR

LOCK appears when the recorder is in the security

lock mode.

37. VCR MODE INDICATORS

• appears during recording.

• tt appears during the rewind mode.

• ss appears during the fast forward mode.

• tt (or ss) flashes during visual search.

• s appears during the playback mode.

• t appears during the reverse play mode.

•

❙❙

appears when the STILL button is pressed

during play mode and disappears when the

STILL or PLAY button is pressed again.

• t

❙❙

(or

❙❙

s) appears while the FIELD REV (or

FIELD ADV) is held depressed in the still

playback mode.

Note: Still playback is restored when the

FIELD REV (or FIELD ADV) button is

released.

38. INDEX INDICATOR

INDEX appears when the ALARM INDEX button is

pressed.

INDEX disappears when the ALARM INDEX button is

pressed again.

INDEX flashes during alarm indexing.

39. DIGITAL COUNTER

Shows the tape counter. The counter does not count

during non-recorded sections of a tape.

40. TAPE SPEED INDICATOR

Shows the tape speed.

REC

PHILIPS LTC3963/51 (E) QR31809

[REAR]

42 43 4544

41. VIDEO IN

Receives video signal from a video camera or another

VCR.

42. VIDEO OUT

For connection to monitor.

43. AUDIO IN

Accepts an audio signal from a camera, external

sound equipment or another recorder (Line: –8 dBm,

50 Kohm, unbalanced).

44. AUDIO OUT

Provides an audio output for a monitor or another

recorder (–9 dBm, 600 ohm, unbalanced).

45. AC INLET

46. RS-232C INTERFACE (D-SUB25) JACK

Used to operate this VCR from a personal computer

on control system.

47. EXTERNAL INTERFACE (15-PIN) JACK

Connect an alarm switch, door sensor, etc. using the

15-pin adapter provided.

q ALARM (A) IN

w ALARM OUT

e ONE SHOT IN

r TAPE END OUT

t TAPE END RESET

y WARNING OUT

u ALARM B IN

i TIME ADJUST

o CAMERA SW OUT

!0 REC START IN

!1 REC OUT

!2 LOW TAPE OUT

!3 REMOTE IN

!4 REC CHECK IN

!5 GND

trewqyui

!2 !1 !0 o!3!4!5

PHILIPS LTC3963/51 (E) QR31809

15-PIN ADAPTER (provided)

It is necessary to connect

to suit your purpose.

SWITCHER

PERSONAL COMPUTER

(with RS-232C jack)

RS-232C reverse type cable

VIDEO CAMERA/RECORDER

PREAMP

MICROPHONE

CAMERA

MONITOR

INSTALLATION

VIDEO CONNECTIONS

Use coaxial cables when connecting a camera and a

monitor to this VCR.

Note: Long cable runs to distant cameras may

cause signal deterioration and/or sync discrep-

ancies. If these problems occur, use video line

amplifiers and/or cameras having phase-adjustable

line-locked vertical sync.

Video Input

In single camera systems, connect the camera to the

Video IN BNC terminal on the VCR rear panel. Use

of a 2:1 interlace camera is highly recommended;

otherwise, the monitor will show vertical distortion

of the TIME/DATE characters.

In multiple camera systems, connect the switcher

output to the Video IN BNC terminal. Because mul-

tiple camera systems require synchronization, use

of cameras having line-locked vertical sync or a gen-

locked master drive/sync source is highly re-

commended. The use of vertical interval switchers

is also recommended.

Video Output

Connect the monitor to the Video OUT BNC terminal

on the rear panel.

AUDIO CONNECTIONS

Note: Audio recording can be performed at the 09

and 27-hour recording speeds and audio playback at

the 09 and 27 speeds.

Audio In:

Accepts an audio signal from a camera,

external sound equipment, or another recorder

(Line: –8 dBm, 50 kohm).

Audio Out:

Provides an audio output for a monitor

or another recorder (–9 dBm, 600 ohm, unbalanced).

USING THE 15-PIN ADAPTER

Attach the wires of the alarm switch, door sen-

sor or warning lamp to the 15-pin adapter

using screws.

After connection, connect the adapter to the

EXTERNAL INTERFACE jack on the rear of the

VCR.

See pages 10 and 11 for details.

Functions of RS-232C Connector Pins

1. Ground 2. Data transmission

3. Data reception 4. Connected to pin 5.

6. Connected to pin 20. 7. Ground

8 ~ 19 and 21 ~ 25. Not connected.

Note: The RS-232C is a standard

null-modem cable that can be

purchased locally.

PHILIPS LTC3963/51 (E) QR31809

EXTERNAL CONNECTIONS

ALARM (A) IN/ ALARM B IN

You can connect two devices including an alarm

switch with a resistance of 1 kohm or less or a door

sensor. Connect pin q or u to pin !5 (ground)

through the switches.

Notes:

• Do not apply a voltage to pin q, u or !5.

• If an alarm is input to the ALARM (A) IN terminal

when an alarm is being input to ALARM B IN, the

input at ALARM (A) IN has priority. However, an

alarm at ALARM B IN is not accepted when an

alarm is being input to ALARM (A) IN.

• The recording conditions are different for the

alarms input to the ALARM (A) IN and ALARM B

IN terminals. See page 19 for details.

ALARM OUT

Approx. 12V is applied to pin w during an alarm

recording.

Notes:

• When you have selected “PULSE” in the “ALARM

OUT” menu in the ALARM display, approx. 12V

pulses will be applied to the output after the

alarm recording ends.

• When you have selected “DURATION” in the

“ALARM OUT” menu in the ALARM display, no

voltage is applied after the alarm recording ends.

• The output impedance is approx. 100 ohm.

ONE SHOT IN

One shot recording is possible when pin e is

shorted to pin !5.

Note: Do not apply a voltage to pin e or !5.

TAPE END OUT

Approx. 12V is applied to pin r when the tape

reaches the end.

Notes:

• This does not operate when you have selected

“REWIND, RE-REC” in the “RECYCLE FUNC-

TIONS” menu in the ALARM display or you have

selected “REWIND, STOP IF ALARM” and no

alarm recording has been made.

• The output impedance is approx. 100 ohm.

TAPE END RESET

The TAPE END OUT can be turned off when pin t is

shorted to pin !5.

Note: Do not apply a voltage to pin t or !5.

Pin Arrangement of 15-Pin Adapter

q ALARM (A) IN

w ALARM OUT

e ONE SHOT IN

r TAPE END OUT

t TAPE END RESET

o CAMERA SW OUT

!0 REC START IN

!1 REC OUT

!2 LOW TAPE OUT

!3 REMOTE IN

!4 REC CHECK IN

!5 GND

y WARNING OUT

u ALARM B IN

i TIME ADJUST

1110954321

87615141312

ALARM (A) IN ALARM B IN GND

qu !5

PHILIPS LTC3963/51 (E) QR31809

EXTERNAL CONNECTIONS (Continued)

CAMERA SW OUT

Pin o outputs the following signal each time a one-

field image is recorded. You can combine this with

a video camera switcher which can be controlled

externally.

The output timing can be specified using the SELEC-

TION MENU screen.

REC START IN

Recording is started when 5 ~ 12V is applied to pin

!0.

REC OUT

Approx. 5V is applied to pin !1 during recording.

The output impedance is 4.7 kohm at this time. The

output stops when recording is interrupted.

LOW TAPE OUT

During recording, when the digital counter counts

up to “32400”, approx. 12V is applied to pin !2. Use

this function as a reference to judge when the tape

is near its end.

The output stops when a TAPE END RESET pulse is

input or the EJECT button is pressed.

Note: The output impedance is approx. 100 ohm.

REMOTE IN

This VCR can be remote controlled when the follow-

ing circuit is connected to pin !3.

The above resistance values have a tolerance of

±2%.

REC CHECK IN

Recording can be checked when pin !4 is shorted to

pin !5 during recording mode. The recorded ma-

terial is played back for several seconds so that you

can check whether recording is made normally or

not.

WARNING OUT

When an abnormality has occurred in this VCR,

approx. 5V is output to pin y to warn the user.

TIME ADJUST

When two or more of this VCR model are used, con-

nect via these terminals. With only one VCR,

specify TIME ADJUST: MASTER, in [OPTIONS]

items on the CLOCK SET display. Specify TIME

ADJUST: SLAVE (default setting at the factory) for

all other VCRs. Each time “2:00:05” is reached, the

VCR set to MASTER transmits pulses for adjustment

to the VCRs set to SLAVE. When the VCRs set to

SLAVE receive these pulses, their clocks will adjust

to the same time as the clock in the VCR set to MAS-

TER.

Note: Be sure to set only one VCR to MASTER. If no

VCR is set to MASTER, or two or more VCRs are set

to MASTER, the TIME ADJUST function will not

operate normally.

5±2 ms

0~0.4V

4.5~5.5V

STOP PLAY STILL REW F.ADV F.F RECMODE UP

PHILIPS LTC3963/51 (E) QR31809

CASSETTE TAPES

It is recommended that you use standard grade VHS

video tapes of the following makers:

maxell TDK Fuji

TAPE LIFE

Slower speed operation in time lapse recording

applies stress to video tape. Tapes should be

inspected and, if necessary, discarded after the total

number of complete tape passes (recording and

playback) exceeds the following limits:

INSERTING A CASSETTE

Note: This is the first step in all VCR operations.

The VCR will not operate without a cassette in place.

To insert a cassette push the cassette through the

cassette compartment door until the VCR mech-

anism pulls it into the compartment.

The tape-in indicator turns on.

REMOVING A CASSETTE

Before removing a cassette, rewind the tape com-

pletely.

To remove a cassette, press the EJECT button. The

cassette will come partially out of the compartment

so you can pull it out.

SAFETY TAB SLOT

Tape Insertion Position

TOP OF CASSETTE

(THIS SIDE UP)

INSERT

VIDEO CASSETTE SAFETY TAB

To prevent accidental erasure of recorded material,

remove the safety tab from the lower left corner of

the cassette.

Recording is impossible when the safety tab is

removed.

Notes:

• The TAB indicator lights when a cassette without

its safety tab is loaded.

• To record again on a cassette that has its safety

tab removed, cover the tab hole with tape. In the

TIMER mode, the TIMER indicator will flash on

and off if the cassette is inserted without its safety

tab slot covered or intact.

TAPE LENGTH

The total recording time at each of the eight tape

speeds depends on the length of the tape used.

The table below shows:

1. The total recording time that can be recorded at

each tape speed mode on E90 and E180 tapes.

2. The pictures per second at each speed.

3. The speeds at which audio can also be recorded.

Use the table to select the tape length which gives

the best compromise between tape cost, total

recording time, and elapsed time between pictures.

SAFETY TAB

Video Cassette Safety Tab

TO PREVENT

ACCIDENTAL

ERASURE, BREAK

OFF THE TAB

TO RECORD AGAIN,

COVER THE HOLE

WITH TAPE

Tape Speed Mode

E90

E180

RECORD

PLAYBACK

RECORD

PLAYBACK

—

2.9

—

Total

Recording

Hours

Pictures/

Second

Audio

4.5

Yes

13.5

16.7

Yes

31.5

7.14

40.5

5.6

120

67.5

135

3.3

168

85.5

171

2.6

240

121.5

243

1.9

Note: The values in this table are approximate.

Tape Speed Complete Tape Passes

09, 27 50

48, 72, 120, 168, 240 25

00 2

PHILIPS LTC3963/51 (E) QR31809

SETUP

On-Screen displays are provided to aid setup of the

programmable functions. The six functions on the

Program Menu appear individually on the monitor

in this order.

1. CLOCK SET

2. TIMER

3. SELECTION MENU 1

4. SELECTION MENU 2

5. ALARM

6. ALARM MEMORY

CLOCK SET

TIMER DISPLAY

SELECTION MENU 1

Initial Program Function Display Formats

ON:

✽✽

❲

❳

:00 :00

❲

❳

:00 :00

❲

❳

:00 :00

❲

❳

:00 :00

❲

❳

:00 :00

❲

❳

:00 :00

❲

❳

THU:

✽✽

TUE:

✽✽

FRI :

✽✽

SUN:

✽✽

ED:

✽✽

SAT :

✽✽

:00 :00

ELECT

ODE

SE EEADPCH S

EVID O

CA A S

ENUION

❲❳

SELECTION MENU 2

ALARM DISPLAY

ALARM MEMORY DISPLAY

:TION U

SPE D:

LAR

RE SIND,

RTION

ION

YDR:AE

:OTU

SET

❲❳

TOP

TCLECYRE

❲

❳

LAR

MMM

A00A

ORYE

❲❳

1–

1–19 FRI990

000:

LOCKCSET

❲❳

TYPO:E

ADJ :US SLAVETTI

OFFSD

PT IOONS

❲❳

ELECT

SEL

TA NEP

TR UOBL

OFF

ZBUZ E

CRT

I:VNEODO

E:RAU C CHECK

ENUION

❲❳

LAR

O:TU

OSE

ON H T

BA :EUT

LEDS

D00BAUD

ERC:

Note: If the VCR is not turned on for about 720

hours after the built-in battery is fully charged (after

the VCR is turned on for more than 48 hours), the

TIME/DATE display will be cleared.

SELECTING A FUNCTION TO BE PROGRAMMED

The program menu will always begin with the

CLOCK SET function, followed by the TIMER,

SELECTION MENU 1, SELECTION MENU 2,

ALARM, and then the ALARM MEMORY functions.

Although the program menu always follows this

order, it is possible to skip any of the available func-

tions during the selection process.

To select the desired program function (and to move

from one program function to the next), press the

PROGRAM button repeatedly until the desired func-

tion display format appears on the monitor.

After the desired function has been selected, follow

the corresponding procedure to set that function.

SETTING THE PROGRAM FUNCTION(S)

The first step in each programming procedure is:

“Press the START/STOP button”. The system

allows up to five minutes for any one function set-

ting to be completed after the START/STOP button

is pushed. If no change/setting is entered within the

five minutes period, the unit will automatically exit

the selected program function. (If this happens, re-

select the desired program function, and follow the

programming procedure for that function.)

The following procedures for setting VCR functions

assume that the desired function has already been

selected.

Note: During programming, holding the SET, UP, or

DOWN button will move/change the displayed infor-

mation at a rapid rate.

PHILIPS LTC3963/51 (E) QR31809

SETTING THE TIME AND DATE

Use the CLOCK SET display to set the date and time.

1. Press the START/STOP button so that [CLOCK

SET] flashes on/off.

2. Press the SET button. The day flashes on/off.

3. Press the UP or DOWN button until the desired

number appears on the monitor.

4. Press the SET button. The month flashes on/off.

5. Press the UP or DOWN button until the desired

number appears on the monitor.

6. Press the SET button. The year flashes on/off.

7. Press the UP or DOWN button until the desired

number appears on the monitor.

8. Press the SET button. The hour flashes on/off.

9. Press the UP or DOWN button until the desired

number appears on the monitor.

10. Press the SET button. The minutes flash on/off.

11. Press the UP or DOWN button until the desired

number appears on the monitor.

12. Press the START/STOP button: the seconds will

start counting and the clock will start. [CLOCK

SET] will flash on/off again at this time.

13. To display the time/date you have set here on

the monitor screen, press the START/STOP but-

ton again to cause [OPTIONS] to flash, and then

proceed with step 2 in item on OSD TYPE on

page 15.

14. Press the START/STOP button three times.

• Make sure that letters [CLOCK SET] or

[OPTIONS] are not flashing.

Notes:

• Perform the same procedure as when setting the

time and date to make corrections after having

set them. The minutes flash on/off when the SET

button is pressed (in step 2 above).

• To record time and date on the tape, display them

on the monitor screen. If they are not displayed

on the monitor, they cannot be recorded on the

tape.

FRI1–

1–19990

000

LOCKCSET

❲❳

TYPO:E

ADJ :US SLAVETTI

OFFSD

PT IOONS

❲❳

TIME (HOUR, MINUTE, SECOND)

DATE (DAY, MONTH, YEAR)

DAY OF WEEK: Corrected

automatically to

match the input

date.

CLOCK SET Display Format Description

OSD TYPE (OFF, FULL or HALF)

TIME ADJUST (MASTER or SLAVE)

PHILIPS LTC3963/51 (E) QR31809

SETUP (Continued)

SETTING [OPTIONS] ITEMS

OSD TYPE: The TIME/DATE display was not

designed to appear at the factory. If you wish to

record the time/date together with image, perform

the following procedure:

There are two types of TIME/DATE display: FULL

and HALF.

TIME ADJUST: When two or more of this VCR

model are connected to pins i TIME ADJUST of

each EXTERNAL INTERFACE jack, the clocks in both

VCRs can automatically be set to the same time

(TIME ADJUST function).

To use the TIME ADJUST function, set one VCR to

MASTER and any others to SLAVE.

1. Press the START/STOP button twice so that

[OPTIONS] flashes on/off.

2. Press the SET button twice so that the TIME

ADJUST: setting flashes on/off.

3. Press the UP or DOWN button to select the setting

(SLAVE or MASTER).

4. Press the START/STOP button again. The selec-

ted setting will light.

Notes:

• You can set OSD TYPE and TIME ADJUST after

you have set the date and time.

• The TIME ADJUST function operates only when

the VCRs are turned on. Therefore, turn the VCRs

on around 2:00:05. This function will not operate

if the times on the MASTER and SLAVE VCRs drift

by more than one hour and 30 minutes.

SUMMER TIME FUNCTION

Set the summer time function when a cassette is not

loaded in this VCR.

Press the SUMMER TIME and UP buttons simul-

taneously in modes other than the timer recording

standby mode; the hour display will be counted up

by one.

Press the SUMMER TIME and DOWN buttons simul-

taneously to count the hour display down by one.

You can change the hour display in one-hour steps

without any limit by pressing the above buttons.

Note: Summer time cannot be set unless TIME/

DATE is displayed.

SETTING THE TIMER

To set the 24 Hour On/Off Timer function

1. Press the START/STOP button twice so that

[OPTIONS] flashes on/off.

2. Press the SET button so that the OSD TYPE: set-

ting flashes on/off.

3. Press the UP or DOWN button to select the setting

(OFF, FULL or HALF).

4. Press the START/STOP button again. The selected

setting will light.

Note: The position of the TIME/DATE display on the

monitor can be adjusted by using the H-POS and

V-POS button on the front panel.

PROGRAM NUMBER

TIMER RECORDING TIME START/STOP

TIMER RECORDING TAPE SPEED

DAY OF WEEK AND PROGRAM NUMBER

1 :TIMER will record for the time set for PROGRAM NUMBER 1

2 :TIMER will record for the time set for PROGRAM NUMBER 2

3 :TIMER will record for the time set for PROGRAM NUMBER 3

4 :TIMER will record for the time set for PROGRAM NUMBER 4

5 :TIMER will record for the time set for PROGRAM NUMBER 5

6 :TIMER will record for the time set for PROGRAM NUMBER 6

7 :TIMER will record for the time set for PROGRAM NUMBER 7

✽ :No recording

TIMER Display Format Description

ON:

✽✽

❲

❳

:00

❲

❳

:00

❲

❳

:00

❲

❳

:00

❲

❳

:00

❲

❳

:00

❲

❳

THU:

✽✽

TUE:

✽✽

FRI :

✽✽

SUN:

✽✽

ED:

✽✽

SAT :

✽✽

:00

20– 2–19991

6: 2:00 091

OPL N

00A

DATE

POWER LOSS (IF SENSED)

DAY OF WEEK

ALARM COUNT*

SECURITY LOCK (IF ACTIVATED)

TIMER (IF ON)

RECORDING SPEED (IN TOTAL HOURS)

TIME

* The ALARM Count Number records alarms from 0 to 99

and then resets to 0 and continues counting.

FULL

20– 2–19991

6: 2:001

DATE

No display

TIME

HALF

No display

OFF

PHILIPS LTC3963/51 (E) QR31809

1. Press the START/STOP button.

The program number (1) flashes on/off.

2. Press the SET button. The start hours flash on/

off.

3. Press the UP or DOWN button until the desired

number appears on the monitor.

4. Press the SET button. The start minutes flash

on/off.

5. Press the UP or DOWN button until the desired

number appears on the monitor.

6. Press the SET button. The stop hours flash on/

off.

7. Repeat steps 3 through 5 to set the stop hours

and minutes.

8. Press the SET button. The timer recording

speed flashes on/off.

9. Press the UP or DOWN button until the desired

number appears on the monitor.

10. Press the SET button after setting the timer

recording speed. The program number of the

next lower line flashes on/off.

11. Repeat steps 2 through 9 to set the program to

the other program numbers.

12. Press the SET button after setting the program

numbers (1) through (7).

The two program event locations of MON flash

on/off.

13. Press the SET button. The first program event

location of MON flashes.

14. Press the UP or DOWN button until the desired

program number appears on the monitor.

15. Press the SET button. The other program event

location of MON flashes on/off.

16. Press the UP or DOWN button until the desired

program number appears on the monitor.

Notes:

• If you do not need to timer record two events

a day, mark either event with an asterisk (✽).

• If two asterisks are displayed, no timer record-

ing is made on that day.

17. After setting two program event locations of

MON, press the SET button. The two program

event locations of the next day of the week

flashes on/off.

18. Press the SET button. The first program event

location of the next day flashes.

19. Repeat steps 12 through 16 to set the program

event locations up to SUN.

20. Press the START/STOP button when the TIMER

has been set.

Notes:

1. Programming the TIMER function does not acti-

vate it. See TIMER recording, page 21.

2. To record the time and date press the PROGRAM

button to display them.

3. When the preset START time is later than the

STOP time, the recording will be made into the

following day.

4. When the START time and STOP time are the

same, a recording will not be made.

5. When the programs for timer recording overlap

each other, recording will be switched to the pro-

gram with the later recording start time.

6. When two programs have the same start time,

the program number with the earlier stop time

has priority.

■ To correct information

1. Press the START/STOP button.

2. Press the UP or DOWN button repeatedly until

the item to be corrected (Program number or

program event location of day of the week)

flashes on/off.

3. When the section to be corrected flashes on/off,

press the SET button.

• Press the SET button again so that only the

digit to be corrected flashes on/off.

4. Press the UP or DOWN button to correct the set

information.

5. After completing the correction, press the

START/STOP button.

Example

•••••

Record

Time

Program number 1

Program number 2

Program number 3

When recording of program

number 3 is terminated, program

number 2 will be recorded for its

remaining time.

PHILIPS LTC3963/51 (E) QR31809

SETUP (Continued)

SETTING THE VCR FUNCTIONS

The SELECTION MENU 1 screen allows you to select the VCR operations and functions to match the appli-

cations.

VIDEO MODE (AUTO, COLOUR, B/W)

• Use during recording or playback if the video signal is unstable,

etc.

AUTO:

COLOUR:

B/W:

The unit automatically detects the type of the video

input or playback signal and switches to the colour

or black-and-white video signal mode, as appro-

priate.

Selects the colour video signal mode.

Selects the black-and-white video signal mode.

27~:

ALL:

09 ONLY:

The pulses are output during recording at 27 or a

longer speed mode.

The pulses are output during recording in all modes.

The pulses are output during recording at the 09

speed mode.

SEARCH SPEED (3, 5, 7 or 9 times the normal speed)

• You can select the visual search speed.

ONE SHOT REC (2, 4, 6, 8 FIELD)

• You can select the number of fields to be recorded during one

shot recording.

BAUD RATE (1200, 2400, 4800, 9600 BAUD)

• You can select the transmission speed with the personal

computer.

CAMERA SW (27~, ALL, 09 ONLY)

• You can select the timing with which pulses are output to

switch the camera.

SELECTION MENU 1 Format Description

ELECT

ESLD

SE EEADP

CH S

ON ER

A0BD

0BAU

EVID O

:ECA A S

ENUION

❲❳

1. Press the START/STOP button.

The VIDEO MODE option “AUTO” flashes on/off.

2. Press the SET button repeatedly until the item

the setting of which you want to change flashes.

3. Press the UP or DOWN button to select the value

or setting you want.

4. After selecting, press the START/STOP button.

PHILIPS LTC3963/51 (E) QR31809

SETTING THE BUZZER

This VCR has a buzzer function.

Use SELECTION MENU 2 to select the times when you wish buzzer to sound.

Note: “OFF” is specified for all buzzer options at the factory.

ELECT

SEL

TA NEP

TR UOBL

OFF

ZBUZ E

CRT

I:VNEODO

E:RAU C CHECK

ENUION

❲❳

LAR

O:TU

TAPE END (ON or OFF)

• To specify whether buzzer turns on or off, synchronized with

pin r TAPE END OUT of the EXTERNAL INTERFACE jack.

ON:

OFF:

Buzzer will keep sounding when tape reaches the end

during recording.

Buzzer will not sound even when tape reaches the end.

TROUBLE (ON or OFF)

• To specify whether buzzer turns on or off when abnormality

occurs in this VCR.

ON:

OFF:

Buzzer will keep sounding if abnormality occurs.

Buzzer will not sound even if abnormality occurs.

NO VIDEO (ON or OFF)

• To specify whether buzzer turns on or off when no video signal

is input during recording.

ON:

OFF:

Buzzer will keep sounding when video signal input stops.

Buzzer will not sound even when input stops.

AUTO REC CHECK (ON or OFF)

• To specify whether buzzer turns on or off if recording is

abnormal after the AUTO REC CHECK function.

ON:

OFF:

Buzzer will keep sounding if recording is abnormal.

Buzzer will not sound even if recording is abnormal.

ALARM OUT (ON or OFF)

• To specify whether buzzer turns on or off when alarm is output.

ON:

OFF:

Buzzer will keep sounding if alarm is output.

Buzzer will not sound even if alarm is output.

SELECTION MENU 2 Format Description

1. Press the START/STOP button.

The TAPE END option “OFF” flashes on/off.

2. Press the SET button repeatedly until the item

the setting of which you want to change flashes.

3. Press the UP or DOWN button to select the value

or setting you want.

4. After selecting, press the START/STOP button.

To stop buzzer:

1. When lights in the VCR display, press

the EJECT button: The tape will come out and

the buzzer will stop.

2. When “A” lights in the VCR display and also “NO

VIDEO” appears on the monitor screen, the

buzzer will stop when video signal is input.

3. When “REC CHECK” appears on the monitor

screen, press the STOP button: The buzzer will

stop.

4. When alarm indicator flashes in the VCR

display, press the ALARM RESET button: The

buzzer will stop.

5. If buzzer function varies in any of the above cases,

the VCR may be abnormal. Press the RESET but-

tons simultaneously: The buzzer will stop.

However, note carefully that all settings will

return to initial values set at the factory.

Note: You can also stop buzzer by switching ON to

OFF in SELECTION MENU 2.

ALARM

TAPE END

PHILIPS LTC3963/51 (E) QR31809

SETUP (Continued)

SETTING THE ALARM

The ALARM function allows the user to set the

recording duration, speed to be recorded and tape

recycle for alarm recordings. When a contact clos-

ure occurs at the ALARM B IN input, the VCR auto-

matically enters the RECORD mode at the pre-pro-

grammed ALARM recording speed. (See Alarm In,

page 10 for a complete description of the ALARM

sequence.) The ALARM recording duration can last

according to the set value, or until the contact clos-

ure is reopened.

The ALARM recording speed can be pre-pro-

grammed to 09~240.

The checking signal is automatically recorded on the

tape at the beginning of each ALARM recording.

Later, you can easily locate the start of each record-

ing by using these signals when watching a re-

corded content. See “ALARM INDEX SEARCH” on

page 23 for details.

See page 15 if you also want to record the date/time.

The TIME/DATE display is set as follows during

ALARM display.

—ALARM stars (✽) will replace the colons (:).

—The recording speed will be changed to 09~240

which was selected at the “SPEED” setting in the

ALARM display.

Notes:

• When the ALARM recording ends, the VCR will

return to the status it was in before the alarm was

input.

• Select 09 at the “SPEED” setting when the dur-

ation is within 30 seconds. If the 27~240 speed is

selected, electronic “marks” are not recorded on

the tape and alarm index search will not operate.

1. Press the START/STOP button. The duration set-

ting flashes on/off.

2. Press the UP or DOWN button until the desired

setting appears on the monitor. (MANUAL, 5,

15, 30 SEC, 1, 3, 5, 10, 30, 60MIN, TAPE END)

3. Press the SET button. The record speed setting

flashes on/off.

4. Press the UP or DOWN button until the desired

setting appears on the monitor. (09~240 HR.)

5. Press the SET button. The alarm ready setting

flashes on/off.

6. Press the UP or DOWN button to select the

alarm ready function. (YES or NO)

Select “YES” if you want to start alarm record-

ing even in the normal record or stop mode.

Select “NO” if you do not want alarm recording

in the stop mode.

7. Press the SET button. The alarm out setting

flashes on/off.

8. Press the UP or DOWN button to select the

alarm out function. See “ALARM OUT” on page

10 for details. (DURATION or PULSE)

9. Press the SET button.

The RECYCLE position flashes on/off.

10. Press the UP or DOWN button to select the

mode at the end of tape. See “TAPE RECYCLE”

on page 21 for details.

11. Press the START/STOP button.

Programming for the ALARM has been com-

pleted.

Caution when input to ALARM (A) IN:

The conditions for recording an alarm input to

ALARM (A) IN are fixed as follows.

Note: The ALARM READY function can be specified

as YES or NO.

[Conditions for recording the input to ALARM (A) IN]

DURATION: MANUAL

MODE: 09

ALARM OUT: DURATION

RECYCLE FUNCTION: REWIND, STOP IF ALARM

:TION U

SPE D:

LAR

RE SIND,

RTION

ION

YDR:AE

:OTU

SET

❲❳

TOP

TCLECYRE

❲

❳

ALARM Display Format Description

DURATION: User programmable length or time the unit

stays in the alarm record mode. (MANUAL, 5 SEC, 15

SEC, 30 SEC, 1 MIN, 3 MIN, 5 MIN, 10 MIN, 30 MIN, 60

MIN or TAPE END)

ALARM RECORDING TAPE SPEED

(09~240)

ALARM READY (YES or NO)

RECYCLE FUNCTIONS

(“REWIND, STOP IF ALARM”, “REWIND, STOP” or

“REWIND, RE-REC”)

ALARM OUT

(DURATION or PULSE)

Page is loading ...

Philips LTC 3963/51 User manual

Brand: Philips

Model: LTC 3963/51

Category: Security access control systems

Type: User manual

Download PDF

report

Philips LTC 3963/51 User manual

Philips LTC 3963/51 User manual

Related papers

Other documents