SIIG 5 User manual

Brand: SIIG

Model: 5

Category: Interface cards/adapters

Type: User manual

This manual is also suitable for

04-0444A

Hi-Speed USB 5-Port PCI

Quick Installation Guide

04-0444A

Features and Benefits

• Compliant with USB specifications revision 2.0

• Conforms to PCI specifications revision 2.2

• Supports simultaneous operation of multiple

high-speed USB 2.0 and USB 1.1 devices

• Supports high-speed (480 Mbps), full-speed (12

Mbps), and low-speed (1.5 Mbps) data transfer

modes

• User friendly hot-swapping feature allows you to

attach/remove USB devices withou turning off your

system

Note: USB 1.1 devices are limited to USB 1.1 speeds

even when they are connected to USB 2.0 host adapter

or USB 2.0 hubs.

System Requirements

PC:

• Pentium-class computer with an available PCI slot

• Windows 2000 SP4 or later/XP SP1 or later/

Server 2003/Vista

Mac:

• Power Mac G3 (blue & white) or later with an

available PCI slot

• Mac OS 10.2.8 or later

Package Contents

• Hi-Speed USB 5-Port PCI

• This quick installation guide

Layout

Figure 1. Board Layout

* Note: This power connector (same as the one used

with your floppy disk drive) is designed to provide

additional power to the board when needed.

Connect this power connector (recommended) when

one of the following conditions occur:

- Device(s) not being detected.

- All ports are used.

Power off your system first before making this

connection.

External

ports

USB Pin-out

Header

Power connector

(Optional)*

Internal port

USB Pin-out Header

The USB pin-out header consists of 4 pins and allows for

1 USB connection.

Important: The internal USB port and the USB Pin-out

Header can not be used at the same time. Do not connect

devices to both ports at the same time.

VCC/+ 5VDC

DATA -

DATA +

GND

Red

Green

White

Black

Figure 2. USB Pin-out Header

Hardware Installation

General instructions for installing the card are provided

below. Since the design of computer cases and

motherboards vary, refer to your computer’s reference

manual for further information, if needed.

Static Electricity Discharge may permanently damage

your system. Discharge any static electricity build up in

your body by touching your computer's case for a few

seconds. Avoid any contact with internal parts and

handle card only by their external edges.

1. Turn OFF the power to your computer and any

other connected peripheral devices.

2. Unplug the power cord and remove your computer's

cover.

3. Remove the slot bracket from an available PCI slot.

4. Carefully align the card to the selected PCI slot,

push the board down firmly, but gently, until it is

well seated.

5. Replace the slot bracket's holding screw to secure

the card.

6. Replace the computer cover and reconnect the power

cord.

Windows Driver Installation

The Hi-Speed USB 5-Port PCI has three built-in USB hosts.

Two hosts handle USB 1.1 devices and the third host

handles USB 2.0 devices. USB 1.1 and USB 2.0 devices are

automatically routed to the correct USB hosts.

Windows Driver Installation

Windows 2000 Service Pack 4 or later, Windows XP

Service Pack 1 or later, Windows 2003 Server, and Vista

have built-in driver support for this controller. Just

install the board and Windows will automatically detect

and install the correct drivers for it. No additional driver

is necessary.

To Verify Windows Installation

Right click My Computer. Click Manage, then click

Device Manager.

Under Universal Serial Bus controllers:

- NEC PCI to USB Open Host Controller

- Standard Enhanced PCI to USB Host Controller

- USB Root Hub (USB 2.0 Root Hub in Win2K)

- USB Root Hub

Mac OS Driver Installation

Mac OS has built-in driver support for this controller.

Just install the board and Mac OS will automatically

detect and install the correct drivers for it. No additional

driver is necessary.

To Verify Mac OS Driver Installation

Mac OS X (v10.2.8)

The only way to verify the board works is actually

connecting devices to the USB ports.

Mac OS X (v10.3.0) or later

Check System Profiler to verify successfull installation.

Click Go, then Utilities. Double click on System Profiler

Under USB

- USB High-Speed Bus

- USB Bus

Blank Page

Technical Support and Warranty

QUESTIONS? SIIG’s Online Support has answers!

Simply visit our website at www.siig.com and click on Support.

Our online support database is updated daily with new drivers

and solutions. Answers to your questions could be just a few clicks

away. You can also submit questions online and one of our technical

support analysts will promptly respond.

This product comes with a lifetime manufacturer warranty. Please see

SIIG website for more warranty details. If you should happen to have

any problems with this product, follow the procedures below.

A) If it is within the store's return policy period, please return the

product to the store where you purchased from.

B) If your purchase has passed the store's return policy period, please

follow these steps to have the product repaired or replaced.

Step 1: Submit your RMA request.

Go to www.siig.com, click Support, then RMA to submit a

request to SIIG RMA. If the product is determined to be

defective, an RMA number will be issued. SIIG RMA department

can also be reached at (510)413-5333.

Step 2: After obtaining an RMA number, ship the product.

• Properly pack the product for shipping. All software, cable(s)

and any other accessories that came with the original package

must be included.

• Clearly write your RMA number on the top of the returned

package. SIIG will refuse to accept any shipping package, and

will not be responsible for a product returned without an

RMA number posted on the outside of the shipping carton.

• You are responsible for the cost of shipping. Ship the product

to the following address:

SIIG, Inc.

6078 Stewart Avenue

Fremont, CA 94538

RMA #:

• SIIG will ship the repaired or replaced product via Ground

in the U.S. and International Economy outside of the U.S. at

no cost to the customer.

Hi-Speed USB 5-Port PCI is a trademark of SIIG, Inc.

SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are

registered trademarks of Microsoft Corporation. Mac and Mac OS are registered trademarks of

Apple Corporation. Pentium is a registered trademark of Intel Corporation. Other names used in

publication are for identification only and may be trademarks of their respective companies.

PRODUCT NAME

Hi-Speed USB 5-Port PCI

FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS

B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE

FCC COMPLIANCE STATEMENT:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE

SIIG, Inc.

6078 Stewart Ave.

Fremont, CA 94538-3152

About SIIG, Inc.

Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer

of I/O connectivity products, including PCI & ISA serial and parallel

ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),

Networking, Sound Cards, and other accessories. SIIG is the premier

one-stop source of upgrades.

SIIG products offer comprehensive user manuals, many user-friendly

features, and are backed by an extensive manufacturer warranty.

High-quality control standards are evident by the overall ease of

installation and compatibility of our products, as well as one of the

lowest defective return rates in the industry. SIIG products can be

found in computer retail stores, mail order catalogs, and e-commerce

sites in the Americas and the UK, as well as through major distributors,

system integrators, and VARs.

SIIG 5 User manual

Brand: SIIG

Model: 5

Category: Interface cards/adapters

Type: User manual

This manual is also suitable for

04-0444A

Download PDF

report

SIIG 5 User manual

This manual is also suitable for

SIIG 5 User manual

Related papers

Other documents