RCA PHD50300 User manual

Category
Receiver
Type
User manual

This manual is also suitable for

  :
-  
PHD50300
Safety Information
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates “dangerous
voltage” inside the product that
presents a risk of electric shock
or personal injury.
This symbol indicates
important instructions
accompanying the product.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Precautions
Please read this manual carefully before using your Monitor and
keep the manual handy for future reference.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO
NOT USE THIS UNIT’S PLUG WITH AN EXTENSION
CORD RECEPTACLE OR OTHER OUTLETS, UNLESS ALL
PRONGS CAN BE FULLY INSERTED. REFRAIN FROM
OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Industry Canada Compliance Notice
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Product: Cinema Screen Display
Equipment Classification: Class B Computer Peripheral
Model: PHD50300
We hereby declare that the equipment specified above conforms to
the technical standards as specified in the FCC rules.
Thomson multimedia Inc.
10330 N. Meridian St.
Indianapolis, IN 46290
Phone: 1-800-433-8974
Cable TV Installer: This reminder is provided to call your
attention to Article 820-40 of the National Electrical Code (Section
54 of the Canadian Electrical Code, Part 1) which provides
guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding system of
the building as close to the point of cable entry as practical.
FCC Information
FCC Regulations state that unauthorized changes or
modifications to this equipment may void the user's authority
to operate it.
This equipment has been type tested and found to comply
with the limits for a Class B Digital Device in accordance
with the specifications in Part 15 of the FCC rules. These
rules are designed to provide reasonable protection against
radio and television interference in a residential installation.
This equipment generates and can radiate radio frequency
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause interference to the radio or
television reception (which you can determine by turning the
equipment off and on), try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving antenna (that is,
the antenna for the radio or television that is
"receiving" the interference).
Change the position of the monitor with respect to
the radio or television equipment that is receiving
the interference.
Move the monitor away from the equipment
receiving the interference.
Plug the monitor into a different wall outlet so the
receiver and the equipment are on different branch
circuits.
If these measures do not eliminate interference, please
consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful
booklet, "How to Identify and Resolve Radio/TV Interference
Problems." This booklet is available from the U.S.
Government Printing Office, Washington D.C., 20402. Please
specify stock number 004-000-00345-4 when ordering copies.
Warnings and Safety Precautions
The monitor is designed and manufactured to provide
long, trouble-free service. No maintenance other than
cleaning is required. Use a soft dry cloth to clean the
panel. Never use solvents such as alcohol or thinner to
clean the panel surface.
The display panel consists of fine picture elements (cells).
Although the display panels are produced with more than
99.99 percent active cells, there may be some cells that do
not produce light or remain lit.
For operating safety and to avoid damage to the unit, read
carefully and observe the following instructions.
To avoid shock and fire hazards:
1. Provide adequate space for ventilation to avoid
internal heat build-up. Do not cover rear vents or
install in a closed cabinet or shelves.
The unit is equipped with cooling fans. If you install
the unit in an enclosure, be sure there is adequate
space at the top of the unit to allow hot air to rise and
escape.
If the monitor becomes too hot, the overheat protector
will be activated and the monitor will be turned off. If
this happens, turn off the power to the monitor and
un-plug the power cord. If the room where the
monitor is installed is particularly hot, move the
monitor to a cooler location, and wait for the monitor
to cool for 60 minutes.
If the problem persists, contact your dealer for service.
2. Do not use the power cord plug with extension cords
or outlets unless all prongs can be completely inserted.
3. Do not expose unit to water or moisture.
4. Avoid damage to the power cord, and do not attempt
to modify the power cord.
5. Unplug unit during electrical storms or if unit will not
be used over a long period.
6. Do not open the unit which has potentially dangerous
high voltage components inside. If the unit is damaged
from opening the cabinet the warranty will be void.
Moreover, there is a serious risk of electric shock.
7. Do not attempt to service or repair the unit. Tmm is
not liable for any bodily harm or damage caused if
unqualified persons attempt service or open the back
cover. Refer all service to authorized Service Centers.
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply.
Continued operation at line voltages greater than 120
Volts AC will shorten the life of the unit, and might
cause a fire hazard.
2. Handle the unit carefully when installing it.
3. Locate set away from heat, excessive dust, and direct
sunlight.
4. Protect the inside of the unit from liquids and small
metal objects. In case of accident, unplug the unit and
have it serviced by an authorized service center.
5. Do not hit or scratch the panel surface as this causes
flaws on the surface of the screen.
6. For correct installation and mounting it is strongly
recommended to use a trained, authorized dealer.
7. Like all phosphor-based display devices, monitors can
be susceptible to uneven phosphor aging under certain
circumstances. Certain operating conditions, such as
the continuous display of a static image over a
prolonged period of time, can result in uneven
phosphor aging if proper precautions are not taken. To
protect your investment in this monitor, please adhere
to the following guidelines and recommendations for
minimizing the occurrence of uneven phosphor aging:
Always enable and use your computer’s screen saver
function during use with a computer input source.
Display a moving image whenever possible.
Always power down the monitor when you are
finished using it.
If viewing with a 4/3 aspect ratio for long periods of
time, set side gray level at 3 or 4.
If the monitor is in long term use or
continuous operation take the following
measures to reduce the likelihood of uneven
phosphor aging:
Lower the BRIGHTNESS and CONTRAST levels as
much as possible without impairing image readability.
Display an image with many colors and color
gradations (i.e. photographic or photo-realistic
images).
Create image content with minimal contrast between
light and dark areas (for example, white characters on
black backgrounds). Use complementary or pastel
color whenever possible.
Avoid displaying images with few colors and distinct,
sharply defined borders between colors.
IMPORTANT TIPS: Caring for Your
Monitor
Safety Information ................................................................................... 1
Warnings and Safety Precautions ................................................................................... 2
IMPORTANT TIPS: Caring for Your Monitor ................................................................... 2
Getting Started ......................................................................................... 5
Contents of the Package ..................................................................................................6
Part Names and Functions – Front View ......................................................................... 7
Part Names and Functions – Back View .......................................................................... 8
Battery Installation ........................................................................................................... 9
Connecting an HD Receiver ............................................................................................. 9
The Back of the HD Receiver ..................................................................................... 9
Connecting Your VCR Or Laserdisc Player.....................................................................10
Connecting Your DVD Player .........................................................................................10
Connecting a Personal Computer .................................................................................. 10
Connecting Components to the Monitor...................................................................... 11
Connecting External Speakers to the Monitor ............................................................. 12
A Quick Tour of the Remote Control ............................................................................. 13
Using Your Remote Control ..................................................................................... 15
Inserting Batteries ..............................................................................................15
Programming the Remote .......................................................................................15
Find Out If You Need to Program the Remote ................................................ 15
How to Program the Remote ............................................................................ 16
Using Automatic Code Search ...........................................................................16
Using Direct Entry ..............................................................................................17
How To Use the Remote Control
After You’ve Programmed It ................................................................................... 17
Programmable Codes for the Remote Control ....................................................... 18
The Menu System ................................................................................... 21
Basic Operations .............................................................................................................22
Power ........................................................................................................................22
Volume ...................................................................................................................... 22
Mute .......................................................................................................................... 22
Navigating the Menus ............................................................................................. 22
The Multi-Screen Feature ........................................................................................ 23
Selecting the Input Signals to be displayed ..................................................... 24
On-Screen Menu Operation .................................................................................... 24
The PICTURE QUALITY Menu .........................................................................................25
Setting the Picture Mode ......................................................................................... 25
Adjusting the Picture Settings in MEMORY Mode ................................................. 26
Setting the Color Temperature................................................................................ 27
Reducing Noise in the Picture ................................................................................. 28
The AUDIO Menu............................................................................................................ 29
The SCREEN Menu ..........................................................................................................30
Selecting a Viewing Size .......................................................................................... 30
Adjusting the Picture Position and Size .................................................................. 31
Auto Picture .............................................................................................................. 31
Contents
The FUNCTION Menu...................................................................................................... 32
On-Screen Displays ...................................................................................................32
Adjusting the Position of the Menu Display .......................................................... 32
Setting the POWER SAVER for Computer Images .................................................. 33
The POWER/STANDBY Indicator .............................................................................. 33
Setting the Gray Level for the Sides of the Screen ................................................ 34
Adjusting for Flickering with Film Mode ................................................................ 34
Adjusting the Display in RGB3 Input Mode ............................................................ 35
Setting the Screen Saver ..........................................................................................35
Setting the PLE ................................................................................................... 35
Turning Orbiter On ............................................................................................36
Setting the Inverse ............................................................................................. 36
Resetting to Default Values ..................................................................................... 37
The OPTIONS Menu ........................................................................................................ 38
Setting the Audio Inputs ......................................................................................... 38
Setting the BNC Connectors .................................................................................... 38
Setting a Computer Image to the Correct RGB
Select Mode .....................................................................................................39
Setting the Monitor to the correct
HD Receiver Mode ........................................................................................... 40
Setting the Picture Size for RGB input signals ........................................................ 40
The SETUP Menu............................................................................................................. 41
Confirming the Frequencies, Polarities, mode
and resolution of Input Signals ......................................................................... 41
Selecting the Language for the Menus .................................................................. 42
Setting the Video Signal Format .............................................................................42
The AUTOTUNING SETUP Menu .................................................................................... 43
Autotuning the Component Buttons on he Remote Control................................ 43
SLEEP TIMER .................................................................................................................... 44
Setting the Sleep Timer............................................................................................ 44
Cancelling the Sleep Timer ................................................................................ 44
Other Information .................................................................................. 45
Installing the Monitor .................................................................................................... 46
Attaching optional mounts or stand to the Cinema
Screen monitor ......................................................................................................46
Connecting Your PC Or Macintosh Computer .............................................................. 47
Mini D-sub 15 Pin VGA Signal Composition ........................................................... 47
Specifications ..................................................................................................................48
Troubleshooting..............................................................................................................49
The Monitor Menu System ............................................................................................ 50
Supported Resolution .................................................................................................... 52
RCA Limited Warranty .................................................................................................... 54
Accessories ......................................................................................................................56
Index ................................................................................................................................ 57
Contents
Connections and Setup
Chapter Overview:
Contents of the Package
Part Names and Functions
Battery Installation
Connections
A Quick Tour of the Remote Control
Chapter 1
Connections and Setup
6 Chapter 1
Contents of the Package
Cinema Screen monitor
Power cord
Ferrite cores
RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15- pin connector)
Remote control unit with two AA batteries
User’s manual
It is highly recommended that you have your monitor installed by a professional. If you are installing
the monitor yourself, refer to the Reference section.
NOTE: If you are planning on attaching the floor stand to your monitor (and not the optional wall mount unit) you may
want to use the safety metal fittings (provided) to give your monitor extra stability.
The safety metal fittings attach to the back of the screen and can then be used to secure the monitor to the wall with strong wire.
Contact your trained, authorized dealer for professional installation.
In order to conform to mandatory FCC standards, you must attach the supplied ferrite cores to both ends of the power
cable (see below).
If you are connecting a computer to the monitor, you must attach the ferrite cores to both ends of the DVI cable to meet
FCC standards.
Attaching the ferrite cores
Set the ferrite cores on the both ends of the DVI cable (supplied), and one end of the power cable (supplied). Close the lid
tightly until the clamps click. Use the band (supplied) to secure the ferrite core.
core (small)
band
band
core (small)
connector
DVI cable
(not supplied)
(monitor side)
core (large)
power cable (supplied)
band
Chapter 1 7
Connections and Setup
Part Names and Functions – Front View
VOLUME
MENU• OK DOWN UP LEFT/- RIGHT/+ INPUT • GO BACK
POWER • STANDBY
V
OLUME
M
ENU
• OK D
OWN
U
P
L
EFT
/- R
IGHT
/+ I
NPUT
• G
O
B
ACK
P
OWER
• S
TANDBY
1. MENU•OK – If no menu is displayed, brings up the
menu. If a menu is displayed, press to select a
highlighted option.
2. VOLUME – Adjusts the volume. When an on-screen
menu is being displayed, moves highlight up and down
( and ).
3. LEFT/- AND RIGHT/- – When Zoom mode is on (press OK
on the remote to turn ZOOM on and bring up the
zoom icon) press Right/+ to enlarge the image or Left/-
to reduce the image.
When a menu is being displayed, used to navigate
through menu ( and ).
1
2
3
4
5
4. INPUT • GO BACK – Switches the input, in the following
order:
*Note: You can set up CMPNT1 or RGB2, but not both.
When an on-screen menu is being displayed, returns
you to the previous menu.
5. POWER/STANDBY indicator – When the power is on,
the light is green. When the power is in Standby
Mode, the light is red.
6. Turns the monitor’s power on and off.
6
Connections and Setup
8 Chapter 1
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO INPUTS
CONTROL
LOCK
on off
RGB 1
HD MONITOR IN
REMOTE
CONTROL
EXTERNAL
CONTROL
L
(MONO)
R
AUDIO 1
RGB 3
DIGITAL RGB
R
G
B
C
R
Y
C
B
P
R
Y
P
B
H-SYNC
V-SYNC
BNC SELECT:/RGB
2
/CMPNT
2
L
(MONO)
R
AUDIO 2
L
(MONO)
R
AUDIO 3
C
R
Y
C
B
Y
P
B
P
R
CMPNT 1
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO INPUTS
CONTROL
LOCK
on off
RGB 1
HD MONITOR IN
REMOTE
CONTROL
EXTERNAL
CONTROL
L
(MONO)
R
AUDIO 1
RGB 3
DIGITAL RGB
R
G
B
C
R
Y
C
B
P
R
Y
P
B
H-SYNC
V-SYNC
BNC SELECT:/RGB
2
/CMPNT
2
L
(MONO)
R
AUDIO 2
L
(MONO)
R
AUDIO 3
C
R
Y
C
B
Y
P
B
P
R
CMPNT 1
1. EXT SPEAKER L and R – Connect speakers here.
2. AC IN – Connect the included power cord here.
3. VIDEO 1, 2, 3 – Connect VCRs, DVDs, Laserdiscs, etc. here.
4. AUDIO1, AUDIO2, AUDIO3 – Connect audio here.
5. CMPNT1 – Connect Laser discs, etc. here.
6. RGB1 – Connect HD receiver here.
7. BNC SELECT –
RGB2: Inputs the analog RGB signal.
CMPNT2: Connect DVDs, Laserdiscs, etc. here.
8. RGB3 (DVI 29pin) – Inputs a digital RGB signal.
9. CONTROL LOCK – When CONTROL LOCK is in the ON position, the buttons on the
monitor’s control panel don’t function.
10. REMOTE CONTROL – This jack is for connecting a wired remote, which is primarily for
commercial applications. The remote included with your monitor is wireless and doesn’t
require connection to the monitor.
11. EXTERNAL CONTROL – This terminal is used when the monitor is controlled by external
equipment.
Part Names and Functions – Back View
1
5
3
7
8
9
11
10
6
4
Chapter 1 9
Connections and Setup
Battery Installation
Remove the battery compartment cover from the back of the remote
control.
Insert batteries. Make sure the polarities (+ and -) are aligned
correctly.
Replace cover.
Connecting an HD Receiver
RCA and PROSCAN HD (high definition) receivers come equipped with an
RGB output jack for optimum quality. Using the RGB cable provided,
connect the HD MONITOR OUT jack on the back of your HD receiver to
the RGB1 (HD MONITOR IN)/AUDIO1 IN jack on the back of the
monitor.
If your HD receiver does not have the type of jack pictured on the right,
connect your HD receiver using the component video jacks and RCA
cable.
For more information on HD receiver connections, see your HD receiver
user’s manual.
The Back of the HD Receiver
ANTENNA B
IN
ANTENNA A
IN
OUT TO TV
VIDEO
S-VIDEO HD MONITOR OUT
AUDIOVCR
CONTROL
DIGITAL AUDIO
OUTPUT
PHONE JACK
SATELLITE
IN
ACCESS CARD
R
R
L
L
HD MONITOR OUT jack
RGB cable
Installing the batteries
Connections and Setup
10 Chapter 1
Connecting Your VCR Or Laserdisc
Player
Use common RCA cables (not provided) to connect your VCR or laserdisc
player to your monitor. To connect your VCR or Laserdisc player:
1. Turn off the power to the monitor and VCR or laser disc player.
2. Connect one end of your RCA cable to the video output connector
on the back of your VCR or laser disc player. Connect the other end
to the video input on the monitor.
3. Use standard RCA cables to connect the audio from your VCR or
laser disc player to AUDIO2 input jacks on the monitor (if your VCR
or laser disc player has this capability). Be careful to keep your right
and left channel connections correct for stereo sound.
4. Turn on the monitor and the VCR or laser disc player.
NOTE: Refer to your VCR or laser disc player user’s manual for more
information about your equipment’s video output requirements.
Connecting Your DVD Player
RCA cables (audio/video cables) are sold as a bundled set.
To connect your monitor to a DVD player:
1. Turn off the power to the monitor and DVD player.
2. Use a standard video cables to connect your DVD player to the CMNT1 input on the monitor,
or use the DVD player’s S-Video output. (Use a standard S-Video cable to connect to the S-
Video input on the monitor.)
3. Turn on the monitor and the DVD player.
Connecting a Personal Computer
If you have a computer with digital RGB output, connect it to the RGB3 jack on the monitor.
For IBM VGA (or compatible) or Macintosh (or compatible) connect to the RGB1 jack on the
monitor.
Chapter 1 11
Connections and Setup
Connecting Components to the Monitor
VCR or Laser Disc Player
DVD Player
Monitor adapter for Macintosh
Personal computer with a digital RGB output
Signal cable (supplied)
To Mini D-Sub 15 pin connector on the
PlasmaSync 4210W
IBM VGA or Compatibles
Macintosh or Compatibles
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO INPUTS
CONTROL
LOCK
on off
RGB 1
HD MONITOR IN
REMOTE
CONTROL
EXTERNAL
CONTROL
L
(MONO)
R
AUDIO 1
RGB 3
DIGITAL RGB
R
G
B
C
R
Y
C
B
P
R
Y
P
B
H-SYNC
V-SYNC
BNC SELECT:/RGB2 /CMPNT2
L
(MONO)
R
AUDIO 2
L
(MONO)
R
AUDIO 3
C
R
Y
C
B
Y
P
B
P
R
CMPNT 1
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO INPUTS
CONTROL
LOCK
on off
RGB 1
HD MONITOR IN
REMOTE
CONTROL
EXTERNAL
CONTROL
L(MONO)
R
AUDIO 1
RGB 3
DIGITAL RGB
R
G
B
C
R
Y
C
B
P
R
Y
P
B
H-SYNC
V-SYNC
BNC SELECT:/RGB2 /CMPNT2
L(MONO)
R
AUDIO 2
L(MONO)
R
AUDIO 3
C
R
Y
C
B
Y
P
B
P
R
CMPNT 1
Connections and Setup
12 Chapter 1
Connecting External Speakers* to the Monitor
The monitor doesn’t have internal speakers, so in order to get sound you must connect external speakers. External speakers
can reproduce sound from VIDEO or RGB signal sources.
External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system
amplifier to the audio outputs.
CAUTION: Unplug the monitor and all connected components before connecting external speakers. Use only speakers
with 6 to 8-ohm impedance and a power output rating of 7 watts or more.
To connect external speakers directly to the monitor:
1. Strip the ends of the speaker wires.
2. Press down the tabs below the speaker terminals and insert the speaker wire and release the tab to secure the speaker
wire connection.
[a] Connect the right speaker (located at right side of the monitor when viewed from the front) positive (+) wire to
RIGHT +.
[b] Connect the right speaker negative (–) wire to RIGHT -.
[c] Connect the left speaker negative (–) wire to LEFT–.
[d] Connect the left speaker positive wire (+) to LEFT+.
*Not included
+
-
+
-
LEFT
RIGHT
VIDEO 1
VIDEO 2
VIDEO 3
VIDEO INPUTS
CONTROL
LOCK
on off
RGB 1
HD MONITOR IN
REMOTE
CONTROL
EXTERNAL
CONTROL
L
(MONO)
R
AUDIO 1
RGB 3
DIGITAL RGB
R
G
B
C
R
Y
C
B
P
R
Y
P
B
H-SYNC
V-SYNC
BNC SELECT:/RGB
2
/CMPNT
2
L
(MONO)
R
AUDIO 2
L
(MONO)
R
AUDIO 3
C
R
Y
C
B
Y
P
B
P
R
CMPNT 1
Chapter 1 13
Connections and Setup
A Quick Tour of the Remote Control
In alphabetical order
ANTENNA When the remote is in HD RCVR mode, switches the HD
receiver between Antenna A and Antenna B.
Arrows Use the arrows to navigate through the menu screens and moves
the Zoom pointer in Zoom mode.
AUX (auxiliary) You can program this button to control any one of the
following: a cable box; most GE, RCA, and PROSCAN audio components;
a laserdisc player; a VCR; or a satellite receiver. Press this button to
operate the component you’ve programmed to work with the AUX button.
CH+/CH– Changes channels on the HD receiver when the remote is in
HD receiver mode. When the Zoom mode is active, zooms in (CH+) or
out (CH-).
CINEMA Press to select one of four screen sizes to suit the type of input
you’re watching.
NOTE: When watching the HD receiver, screen size is controlled
through the HD receiver menu system.
CLEAR Clears on-screen displays and returns you to normal viewing.
CMPNT Toggles between CMPNT1 and CMPNT2 inputs.
GO BACK In HD receiver mode, returns you to the previous channel.
When in the menu system, returns you to the previous menu.
GUIDE In HD receiver mode, brings up the on-screen program guide.
INFO Brings up channel information.
INPUT Changes the video input.
MENU Brings up the on-screen menu.
MONITOR Turns the power to the monitor on and puts the remote in
Monitor mode so you are able to control the monitor.
MUTE Reduces sound to an inaudible level.
Numbers Use the number keys to make numerical entries.
OK/ZOOM When in Monitor mode (press the MONITOR button) and
using on-screen menus, press OK to select a highlighted menu function.
When there are no on-screen menus displayed, press OK to bring up the
zoom pointer. Using the arrow buttons, position pointer on the part of the
screen you want to zoom on, then use the CH+/- buttons to zoom in/out.
STOP PAUSE
MONITOR
ON•OFF
AUX
DVD
HD RCVR
RECORD
PLAY FORWARDREVERSE
SLEEP
WHO•MULTI
MUTE
INFO
MENU
OK
CLEAR
GUIDE
ANTENNA
1
2
3
4
5
6
7
8
9
0
INPUT
VCR1
VCR2
C
H
+
C
H
V
O
L
V
O
L
GO BACK
CINEMA
RGB
CMPNT VIDEO
Z
O
O
M
I
N
Z
O
O
M
O
U
T
Z
O
O
M
u n i v e r s a l
SOURCE
Connections and Setup
14 Chapter 1
ON•OFF Toggles power on and off for the components that you have
programmed. For example, if you are in VCR mode, turns VCR on and
off.
REVERSE, PLAY, FORWARD, STOP, PAUSE, RECORD (transport keys)
Use with components programmed to work with your remote control
(VCR, DVD player, audio components).
RGB Depending on how you set up the monitor, toggles between RGB1,
RGB2*, and RGB3.
*Note: You can set up CMPNT2 OR RGB2, but not both. If CMPNT2 is
set up, RGB2 will not appear when you use the RGB button.
SLEEP Brings up the sleep timer, which is used to turn the monitor off
automatically after a set amount of time.
VCR1, VCR2, DVD, HD RCVR, MONITOR These are the component
buttons used to put the remote control into the correct mode to operate
that particular component. The correct video source must first be selected
(VIDEO or RGB) or Autotuning must be set up.
VOL</VOL> Adjusts the volume.
VIDEO Selects whatever component is hooked up to the video source
inputs.
WHO•MULTI When in Monitor mode, activates the multi-screen feature.
The Multi-screen feature allows you to select a screen mode for viewing a
single picture, side-by-side pictures, or picture-in-picture (PIP). Brings up
personal viewer profiles for some components.
ZOOM IN When in zoom mode (press the MONITOR button an then
the OK button to access zoom mode) enlarges the picture. When in zoom
mode, use the arrow buttons to pan and scan the entire picture.
ZOOM OUT When in zoom mode (press the MONITOR button an then
the OK button to access zoom mode) decreases the magnification of the
picture. If picture is distorted, zoom out to restore to normal.
STOP PAUSE
MONITOR
ONOFF
AUX
DVD
HD RCVR
RECORD
PLAY FORWARDREVERSE
SLEEP
WHOMULTI
MUTE
INFO
MENU
OK
CLEAR
GUIDE
ANTENNA
1
2
3
4
5
6
7
8
9
0
INPUT
VCR1
VCR2
C
H
+
C
H
V
O
L
V
O
L
GO BACK
CINEMA
RGB
CMPNT VIDEO
Z
O
O
M
I
N
Z
O
O
M
O
U
T
Z
O
O
M
u n i v e r s a l
SOURCE
Chapter 1 15
Connections and Setup
Using Your Remote Control
Inserting Batteries
1. Remove the battery compartment cover from the remote control.
2. Insert batteries (included) as shown on the diagram inside the battery
compartment.
3. Replace the battery compartment cover.
Use your remote control from a distance of about 7m/23 feet from the
monitor’s remote control sensor and at a horizontal angle of within 30°.
The remote operates on line of sight, so if there is anything blocking the
path between the remote and the remote control sensor on the front of
the monitor, the remote may not work.
Don’t expose the remote control sensor on the front of the monitor
to direct sunlight or strong artificial light.
Don’t get the remote control wet.
Avoid heat and humidity.
When not using the remote for a long period of time, remove the
batteries.
Programming the Remote
The universal remote control that came with your monitor is already
programmed to operate most RCA, GE, and PROSCAN VCRs, DVD
players, laserdisc players, and satellite receivers. This remote is also
capable of operating many other brands of remote-controllable electronic
components, but you must program it to do so.
Find Out If You Need to Program the Remote
To determine whether the universal remote needs to be programmed,
turn on one of your components, such as a VCR. Point the remote control
at the component and press the component button (for example, the VCR
button). Now press the ON•OFF button on the remote. If the component
doesn’t turn off, you need to program the remote control in order for it to
operate that component.
Installing the batteries
INPUT SELECT
POWER STANDBY
VOLUME
Approx.
7m/23 ft.
30°30°
STOP PAUSE
MONITOR
ON OFF
AUX
DVD
SAT CABLE
RECORD
PLAY FORWARDREVERSE
SLEEP
GO BACK
C
H
+
C
H
-
V
O
L
V
O
L
WHOMUTE
INFO
MENU
CLEAR
GUIDE
ANTENNA
1
2
3
4
5
6
7
8
9
0
INPUT
VCR1
VCR2
OK
Z
Z
Z
CINEMA
VGA
VIDEO
Y u v
SOURCE
Connections and Setup
16 Chapter 1
How to Program the Remote
There are two ways to program the remote control: automatic code search and direct entry.
Component Buttons
These are the buttons you program to operate another
component.
MONITOR
ONOFF
AUX
DVD
HD RCVR
VCR1
VCR2
Using Automatic Code Search
1. Turn on the component you want the remote to operate (VCR, HD
receiver, etc.)
2. Press and hold the component button that corresponds to the
component you want the remote to operate (VCR, HD receiver, etc.).
While you hold down the component button, press and hold
ON•OFF (when the red light on the remote turns on, release both
buttons).
Note: Automatic Code Search can’t be used with the AUX button.
3. Press PLAY (the red light on the remote starts flashing).
The remote is searching the first set of component codes (there are
several sets of codes). If the component you want to operate doesn’t
turn off automatically after 5 seconds, press PLAY again (the red light
starts flashing again as the remote searches through the next set of
codes).
Continue pressing PLAY until the component turns off.
NOTE: If the component doesn’t turn off after you’ve pressed the PLAY
button 20 times, the component can’t be programmed.
4. Press REVERSE and wait 2 seconds. Repeat this step until the
component turns back on.
5. To finish, press and hold the STOP button until the red light on the
remote turns off.
Chapter 1 17
Connections and Setup
Using Direct Entry
1. Turn on the component you want the remote to operate (the red light on the remote turns
on).
2. Look up the brand and code number(s) for the component on the code list on the following
pages.
3. Press and hold the component button that corresponds to the component you want the remote
to operate (VCR, RCA DVD, etc.).
4. Enter the code from the code list. When you begin entering numbers, the red light on the
remote turns off. When the last number is entered, the red light turns back on. If the incorrect
code is entered, the red light will flash.
5. Release the component button. The red light on the remote turns off.
6. Press ON•OFF to see if the component responds to the remote commands. If it doesn’t, try
pressing the component button and then ON•OFF again.
6. If you get no response, repeat these steps using the next code listed for your brand, until the
component responds to the remote commands.
How To Use the Remote Control After You’ve Programmed It
Once the remote control has been programmed successfully, you’re ready to use it to operate
other components.
1. Press one of the video source buttons to select a component (VIDEO or RGB) to operate.
2. Press the component button (MONITOR, VCR, DVD, AUX, or HD RCVR) to use the Transport
buttons (REVERSE, PLAY, FORWARD, STOP, PAUSE, and RECORD) to operate the component.
3. Press ON•OFF to turn the component on or off.
NOTE: If you keep pressing buttons and nothing happens, you may have the wrong video
source or wrong component selected. You must select the correct video source and the
component button that matches the component you want to operate.
Connections and Setup
18 Chapter 1
Magnavox .......... 2021, 2022, 2062, 2063, 2104,
2108, 2124
Magnin ........................................................ 2013
Marantz .... 2009, 2010, 2011, 2016, 2018, 2021,
2058, 2062,2064
Marta ........................................................... 2014
Masushita .................................................... 2021
MEI ............................................................... 2021
Memorex ............ 2002, 2011, 2013, 2014, 2021,
2023, 2026, 2104, 2131
MGA ........................................ 2029, 2065, 2113
MGN Technology ........................................ 2013
Midland ....................................................... 2053
Minolta .................................... 2055, 2056, 2107
Mitsubishi ........... 2029, 2055, 2056, 2065, 2066,
2067, 2069, 2070, 2071, 2072, 2073, 2074, 2106,
2113, 2123
Montgomery Ward ........................... 2075, 2131
Motorola ........................................... 2021,2131
MTC ......................................... 2002, 2013, 2026
Multitech ... 2002, 2013, 2016, 2026, 2053, 2061
NEC ........... 2009, 2010, 2011, 2016, 2018, 2058,
2064, 2076, 2078, 2079, 2111, 2123
Nikko ........................................................... 2014
Noblex ......................................................... 2013
Olympus ...................................................... 2021
Optimus ............................................. 2014, 2131
Optonica ...................................................... 2096
Orion ........................................................... 2035
Panasonic .. 2021, 2022, 2109, 2125, 2126, 2127
Pentax .................. 2016, 2055, 2056, 2107, 2120
Pentex Research .......................................... 2018
Philco ............................. 2021, 2022, 2062, 2063
Philips ............................ 2021, 2062, 2096, 2124
Pilot ............................................................. 2014
Pioneer ................ 2010, 2055, 2080, 2081, 2123
Portland ......................... 2016, 2017, 2019, 2110
PROSCAN ........................................... 2000, 2001
Protec .......................................................... 2061
Pulsar ........................................................... 2104
Quarter ........................................................ 2011
Quartz ......................................................... 2011
Quasar ..................................... 2021, 2022, 2125
RCA 2000, 2001, 2003, 2013, 2021, 2055, 2056,
2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089,
2090, 2091, 2107, 2115, 2120, 2125
Radio Shack/Realistic .... 2002, 2011, 2013, 2014
2021, 2022, 2023, 2026, 2029, 2049, 2050, 2096,
2131
Radix ............................................................ 2014
Randex ......................................................... 2014
Ricoh ............................................................ 2128
Runco ........................................................... 2104
Samsung .... 2005, 2013, 2015, 2033, 2053, 2112
Sanky ................................................. 2131, 2104
Sansui ............................ 2010, 2092, 2111, 2123
Sanyo ....................................... 2011, 2013, 2023
Scott 2012, 2015, 2025, 2032, 2035, 2038, 2065,
2093, 2116
Sears2011, 2014, 2021, 2023, 2048, 2049, 2050,
2051, 2055, 2056, 2107, 2118
Sharp 2002, 2017, 2029, 2094, 2095, 2096, 2131
Shintom ......................... 2004, 2056, 2061, 2098
Shogun ........................................................ 2013
Signature .......................................... 2002, 2131
Singer ...................................... 2021, 2061, 2128
Sony ........... 2002, 2004, 2098, 2099, 2119, 2128
STS ..................................................... 2021, 2107
Sylvania .... 2002, 2021, 2022, 2026, 2062, 2063,
2065, 2124
Symphonic ......................................... 2002, 2026
Tandy ................................................. 2002, 2011
Tashiko ........................................................ 2014
Tatung ............................................... 2058, 2111
TEAC .................... 2002, 2026, 2058, 2085, 2111
Technics ............................................. 2021, 2109
Teknika ...... 2002, 2014, 2021, 2026, 2100, 2129
TMK ......................................... 2013, 2024, 2047
Toshiba2015, 2049, 2051, 2055, 2065, 2093, 2116
ToteVision .......................................... 2013, 2014
Unitech ........................................................ 2013
Vector Research ............ 2009, 2010, 2015, 2016
Victor ........................................................... 2010
Video Concepts ... 2009, 2010, 2015, 2016, 2113
Videosonic ................................................... 2013
Wards ....... 2002, 2013, 2014, 2015, 2021, 2023,
2026, 2029, 2055, 2056, 2061, 2096, 2101, 2102,
2103, 2107, 2116, 2131
XR-1000 ................................... 2021, 2026, 2061
Yamaha ..... 2009, 2010, 2011, 2018, 2058, 2111
Zenith .................. 2004, 2098, 2104, 2119, 2128
Cable Box (AUX or HD RCVR button)
ABC .. 5002, 5003, 5004, 5005, 5006, 5007, 5053
Antronix ............................................ 5008, 5009
Archer ............................ 5008, 5009, 5010, 5011
Cabletenna .................................................. 5008
Cableview .................................................... 5008
Century ........................................................ 5011
Citizen ......................................................... 5011
Colour Voice ...................................... 5012, 5013
Comtronics ........................................ 5014, 5015
Contec ......................................................... 5016
Eastern ......................................................... 5017
Garrard ........................................................ 5011
GC Electronics ............................................. 5009
Gemini ..................................... 5018, 5019, 5049
General Instrument .................................... 5003
Hamlin ................. 5020, 5021, 5022, 5035, 5045
Hitachi ......................................................... 5003
Hytex ........................................................... 5002
Jasco ............................................................ 5011
Jerrold ....... 5003, 5005, 5007,5018, 5023, 5024,
5046, 5053
Magnavox ................................................... 5025
Memorex ..................................................... 5026
Movie Time.............................. 5002, 5027, 5028
NSC .......................................... 5002, 5027, 5028
Oak ........................................... 5002,5016, 5029
Panasonic .......................................... 5048, 5052
Paragon ....................................................... 5026
Philips ....... 5011, 5012, 5013, 5019, 5025, 5030,
5031, 5032
Pioneer .............................................. 5033, 5034
Pulsar ........................................................... 5026
RCA .......................................... 5047, 5049, 5052
Realistic ............................................. 5009, 5049
Regal .................................................. 5022, 5035
Regency ....................................................... 5017
Rembrandt .................................................. 5003
Runco ........................................................... 5026
Samsung ............................................ 5014, 5034
Scientific Atlanta .......... 5006, 5036, 5037, 5038
Signal ................................................. 5014, 5018
Programmable Codes for the Remote Control
VCR (VCR1, VCR2 or AUX button)
Admiral ........................................................ 2131
Adventura ................................................... 2026
Aiko ............................................................. 2027
Aiwa .................................................. 2002, 2026
Akai 2003, 2004, 2005, 2007, 2008, 2111, 2112,
2113
American High ............................................ 2021
Asha ............................................................. 2013
Audio Dynamics ................................ 2009, 2010
Audiovox ..................................................... 2014
Bell & Howell .............................................. 2011
Beaumark .................................................... 2013
Broksonic ........................................... 2012, 2025
Calix ............................................................. 2014
Candle2013, 2014, 2015, 2016, 2017, 2018, 2019
Canon ...................................... 2021, 2022, 2114
Capehart ............................................ 2020, 2110
Carver .......................................................... 2062
CCE ..................................................... 2027, 2061
Citizen ..... 2013, 2014, 2015, 2016, 2017, 2018,
2019, 2027
Colortyme .................................................... 2009
Colt .............................................................. 2061
Craig .............................. 2013, 2014, 2023, 2061
Curtis-Mathes2000, 2002, 2009, 2013, 2016, 2018,
2021, 2022, 2024, 2115
Cybernex ..................................................... 2013
Daewoo2015, 2017, 2019,2025, 2026, 2027, 2028,
2110
Daytron ....................................................... 2110
Dbx .................................................... 2009, 2010
Dimensia ...................................................... 2000
Dynatech ........................................... 2002, 2026
Electrohome ...................................... 2014, 2029
Electrophonic .............................................. 2014
Emerson2002, 2012,2014, 2015, 2021, 2024, 2025,
2026, 2029, 2030, 2032, 2033, 2034, 2035, 2036,
2037, 2038, 2039, 2040, 2041, 2042, 2044, 2045,
2047, 2065, 2105, 2113, 2116, 2117, 2130
Fisher ........ 2011, 2023, 2048, 2049, 2050, 2051,
2052,2118
Fuji ..................................................... 2021, 2119
Funai .................................................. 2002, 2026
Garrard ........................................................ 2026
GE2000, 2001, 2013, 2021, 2022, 2053, 2115, 2120
Goldstar ............... 2009, 2014, 2018, 2054, 2121
Gradiente .................................................... 2026
Harley Davidson .......................................... 2026
Harman Kardon .......................................... 2009
Harwood ..................................................... 2061
Headquarter ................................................ 2011
Hitachi ...... 2002, 2055, 2056, 2057, 2107, 2111,
2120, 2122
HI-Q ............................................................. 2023
Instant Replay ............................................. 2021
JCL ................................................................ 2021
JC Penney 2009, 2010, 2011, 2013, 2014, 2021,
2022, 2055, 2056, 2058, 2059, 2060, 2107, 2118
Jensen ...................................... 2055, 2056, 2111
JVC ... 2009, 2010, 2011, 2018, 2058, 2111, 2123
Kenwood ............ 2009, 2010, 2011, 2016, 2018,
2058, 2111,2123
KLH .............................................................. 2061
Kodak ................................................ 2014, 2021
Lloyd .................................................. 2002, 2026
Logik ............................................................ 2061
LXI ................................................................ 2014
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62

RCA PHD50300 User manual

Category
Receiver
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI