Shure R115S User guide

Shure
Brand
Shure
Model
R115S
Category
Microphone accessories
Type
User guide

Shure R115S is a replacement cartridge kit for Super 55 and 55SH Series II Microphones. This kit includes a new cartridge, two self-tapping screws, and an instruction sheet, allowing you to easily replace the cartridge in your microphone. With the new cartridge, you can enjoy improved sound quality and performance from your microphone.

Features:

  • Easy to install: The cartridge can be replaced in just a few steps using the included screws and instructions.
  • Improved sound quality: The new cartridge provides improved sound quality and performance, ensuring that your microphone captures your voice clearly and accurately.

Shure R115S is a replacement cartridge kit for Super 55 and 55SH Series II Microphones. This kit includes a new cartridge, two self-tapping screws, and an instruction sheet, allowing you to easily replace the cartridge in your microphone. With the new cartridge, you can enjoy improved sound quality and performance from your microphone.

Features:

  • Easy to install: The cartridge can be replaced in just a few steps using the included screws and instructions.
  • Improved sound quality: The new cartridge provides improved sound quality and performance, ensuring that your microphone captures your voice clearly and accurately.
R115S CARTRIDGE REPLACEMENT
Remove screws (4)
Remove Case
1
2
3
4
6
5
7
New Cartridge – R115S
Two self tapping 4-40, 5/8” long Phillips
head screws
Instruction sheet
Kit Contains:
Tools Required:
#2 Phillips Head Screwdriver
Wire Cutter
Wire Stripper
Low wattage Soldering Iron
Solder
Instructions:
Secure base of microphone housing to keep it from rolling or sliding off of work surface.
1
Remove the four Philips screws that hold the front case to the microphone housing. Remove the front case
and set aside.
2
Unscrew the four Phillips screws that hold the black microphone cartridge into the housing. Save two as they
will be used to secure the new cartridge.
3
Carefully withdraw the microphone cartridge taking care not to stretch or break the three wire leads; blue, black
and yellow.
4
Cut the three wires at the base of the cartridge. Discard cartridge. (55SH only)
For Super 55: Unsolder wires at PC board.
5
Holding the wires out and down towards the stem of the microphone, place the Super 55 bracket/cartridge
assembly into the microphone housing. Do not force. Cartridge will only fit if the PC board and solder pads are
facing up and at the bottom of the base.
6
Install two of the screws that held the old cartridge in place in the upper two holes of the bracket. Install the two
longer screws, supplied with the kit, into the lower 2 holes of the bracket. Tighten the screws to hold the bracket
in the housing.
7
Strip off approximately ¼ in of insulation from the end of each wire and tin with solder - 55SH only.
8
Tuck any excess wire under the bracket.
10
Place the front case half back on the microphone housing with the Shure logo oriented as shown
in illustration.
11
Reinstall and tighten the four Phillips screws that were removed in step two. Return handle to
normal position.
12
Support microphone
Remove four screws that hold in
the cartridge.
Save two
Carefully withdraw cartridge
Do not stretch or break these leads
Cut wires at the base of cartridge
(55SH only)
Hold wires out of the way and towards the
handle of microphone.
Place the Super 55 bracket/cartridge assembly into
the microphone housing. Do not force.
Cartridge will only fit if the PC board and solder pads
are facing up and at the bottom of the base.
Install two of the
screws that held the
old cartridge in place
in the upper two holes
of the bracket.
Install the two longer screws, supplied with the kit, into
the lower 2 holes of the bracket.
CARTRIDGE REPLACEMENT STEPS
Solder each wire to the pad on the circuit board labeled with its corresponding color. Solder Yellow wire to yellow
pad , black to black, and blue to blue (see note).
9
NOTE: When replacing the cartridge in the Super 55 there is no blue wire.
8
10
9
11
R115S Replacement Cartridge Kit for
Super 55 and 55SH Series II Microphones
Strip off approximately ¼
in of insulation
Solder wire to the pad
Tuck excess wire
under bracket
Replace the front case
Tin with solder
Logo must be oriented as shown
Reinstall the four Phillips screws that
were removed
©2009 Shure Incorporated
27A12880 (Rev. 1)
Printed in U.S.A.
CARTRIDGE REPLACEMENT STEPS
SHURE Incorporated http://www.shure.com
United States, Canada, Latin America, Caribbean:
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055
Blue wire to blue pad – when
replacing cartridge in 55SH
Series II microphone
Note: No blue wire in Super 55
microphone
Black wire to black pad
Yellow wire to yellow pad
  • Page 1 1
  • Page 2 2

Shure R115S User guide

Shure
Brand
Shure
Model
R115S
Category
Microphone accessories
Type
User guide

Shure R115S is a replacement cartridge kit for Super 55 and 55SH Series II Microphones. This kit includes a new cartridge, two self-tapping screws, and an instruction sheet, allowing you to easily replace the cartridge in your microphone. With the new cartridge, you can enjoy improved sound quality and performance from your microphone.

Features:

  • Easy to install: The cartridge can be replaced in just a few steps using the included screws and instructions.
  • Improved sound quality: The new cartridge provides improved sound quality and performance, ensuring that your microphone captures your voice clearly and accurately.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents