Elvox ZKN2 User manual

Brand: Elvox

Model: ZKN2

Category: Garage Door Opener

Type: User manual

This manual is also suitable for

The ZN10 operator integrates perfectly with the design of any up and over door with-

out essentially altering its appearance. It also features quiet and linear operation

which renders it safe and agreeable to use, thanks not least to a courtesy light timed

to switch off after 3 minutes.

Total safety

The use of low voltage motors (12 V) eliminates any risk of electrical discharges or

accidental electrification of the structure.

Electronic clutch

if the door is obstructed by an obstacle, an electronic device will immediately stop

the automatic system as soon as the slightest hint of abnormal friction is detected,

and reverse the movement by about 10 cm.

Easy to install

Simpler electrical installation thanks to the separate control unit, optimizing mainte-

nance and assembly (can be connected to the power supply using an existing sock-

et). The control unit lights up automatically (when the motor is activated) and has a

button for opening and closing the door. The absence of any “control head” at the

end of the mechanism, and consequently the reduction in length of 310 mm, is espe-

cially advantageous in situations where space may be limited.

Maintenance-free and reliable

With the new operating principle of a motor travelling along a fixed chain in a track,

the automatic system is quiet and long-lasting, and requires no maintenance.

COMPLETE KIT FOR SECTIONAL DOOR

Type ZKN1

COMPLET KIT FOR SPRING OR COUNTERWEIGHT HORIZONTALLY-PIVOTED DOOR

Type ZKN2

ZN SERIES ACTUATOR

ZN10 AUTOMATIC SYSTEM FOR SECTION-

AL AND SPRING OR COUNTERBALANCE

HORIZONTALLY PIVOTED DOORS

General description

The ZN10 electromechanical operator is

designed for sectional and spring or counter-

balance up and over doors.

Thanks to its push-pull and closing force,

650N, it will open and close doors up to 10 m

max without difficulty. This generation of

operators is designed with the accent on ease

of installation but also on the strength of the

materials employed.

OVERALL DIMENSIONS

Mod. ZN10

- Electromechanical operator:

- Control unit

Mod. ZN20

116

270

140

135

125

270

2600

1600

500

250

120

- Jointed C-track

- Overall length: 3230 mm

- Dimensions of pack:

ZN10 motor unit: 160x160x800 mm

Tracks: 160x55x1600 mm

Press to return to index

ZN SERIES ACTUATOR

PACKAGING CHECK-LIST

The ZN10 operator does not cause particular handling problems during transport.

The standard version must be combined with the 2600 mm guide (working stroke of motor), type ZN20. The two components are

packed in small cardboard boxes. They must be stored in a dry area that is protected from the weather.

Contents of article ZN10 (Fig. A).

- No. 1 control unit with electronic card and 433 MHz receiver

- No. 1 electromechanical operator

- No. 1 longitudinal rod and door corner fitting

- No. 1 front bracket supporting the track

- No. 1 ceiling suspension bracket for the track

- No. 1 instruction manual

- No. 2 remote controls Type ZT03

Contents of article ZN20 (Fig. A).

- No. 2 C-tracks length 1600 mm.

- No. 2 sliding limit switches

- No. 1 chain with chain raceway

- No. 1 snap-on component with cable for connections to the control unit (6900 mm)

- No. 1 connector for the two C-tracks

- No. 1 ceiling suspension bracket

- No. 1 bag containing material required for assembly.

Assembly material in the bag (Fig. B)

- No. 4 wood screws 8x60

- No. 4 plugs S10

- No. 5 washers 8.4

- No. 2 wood screws 4x50

- No. 2 plugs S6

- No. 5 hexagonal head screws

for metal plate, 6.5x19

- No. 1 long bolt 10x35

- No. 1 short bolt 10x35

- No. 2 safety clips

- No. 1 self-locking nut M8

- No. 1 suspension spring

- No. 1 fixing pin M8x110

- No. 1 two-component chain-link

Fig. A/ZN

Fig. B/ZN

In addition to Type ZN10-ZN20, the Kit ZKN2

also contains Type ZN21 (curved arm).

Control unit supply voltage 230 (-10% +6%) V A.C.

Nominal frequency 50-60 Hz

Motor 12V D.C.

Rated current 0.7 A

Motor power 150 W

Max. torque. 650 N

Nominal traction force 195 N

Maximum speed 180 mm/s

Power consumption in stand-by ~2N

Relative noise (only automation)

< 75 DBA

Working temperature: -20°C ÷+55°C

Protection level: IP40

Working cycle: 15%

Max. surface area of door: 10m

max. height of door (standard version) 2600 mm

Radio receiver 433 MHz

Courtesy light YES (24 V, 21 W bulb)

Weight 16 Kg

Working stroke standard version 2600 mm

TECHNICALTECHNICAL SPECIFICATIONS SHOWN ON DATA PLATE ZN10

Doors with a height exceeding 2600 mm require the addition of an extension Type ZN22 of 1600mm (working stroke 4,200 mm.).

Press to return to index

ZN SERIES ACTUATOR

MECHANICAL INSTALLATION

N.B. Choose the desired mounting variation

In case B modify the chain supply voltage.

Fig. 1) Loosen the limit switch (1) on the first track, "end

track", and move it in the direction shown by the

arrow. Open the chain (2) by 180°

Fig. 2) Unlock the motor (1) by pulling the manual release

(N). Insert the chain (2) in the motor so that it

engages with the pinion (3).

Fig. 3) Insert the motor (1) in the "track" (2).

Fig. 1

Fig. 2

Fig. 3

Press to return to index

ZN SERIES ACTUATOR

Fig. 4) Insert the connector joining (2) the two tracks (1). Bring the tracks together until they stop

and lock.

Fig. 5/AC-6/AC-7/AC

On the installation - variation A/C, insert the fixing bracket (a) in

the chain and turn it 90° (b). Insert the terminal head (5) in the

guide (c) , and the washer (4) with spring (3) in the draught dowel

(2). Screw the dowel in the fixing bracket (1). Tighten the chain

until the mark (arrow).

Fig. 5A/B-5B/B-6/B-7/B

On the installation - variation B, invert the supply voltage head.

Insert the fixing bracket (a) in the chain and turn it 90° (b).

Insert the terminal head (6) in the guide (c) and the washer (5)

with spring (4) in the draught dowel (3). Screw the dowel in the

fixing bracket (1).

Tighten the chain until the mark (arrow).

Attention! Do not tighten the chain from the power supply side,

because it is already pre-tightened in the lab.

Fig. 4

Fig. 5/AC

Fig. 7/AC

Fig. 6/AC

Fig. 5A/B

Fig. 5B/B

Fig. 6/B

Fig. 7/B

Press to return to index

ZN SERIES ACTUATOR

Fig. 8

Fig. 9

Fig. 10

Fig. 11

Fig. 12

Fig. 8

Fit the bracket for the guide fixing to the ceiling as shown

in the figure.

Fig. 9

Insert the fixing bracket (1) in the guide (2).

Fig. 10

Fix the bracket, guide angle (2) with the screw (1) and

the nut (3) to terminal (4).

Fig. 11

Determine the highest opening point of the door (THP):

the ceiling must be above this point, and at a distance of

at least 35 mm.

The distance between the maximum door opening point

and the lower guide must be included between 5 mm

(min.) and 65 mm. (max), while the thrust arm must have

an angle of 30°.

Fig. 12

The guide can be fixed either on the architrave (A) either

to the ceiling (B).

Fig. 13

Measure the centre of the door (C) and mark the point on

the door, on the lintel and on the ceiling.

Fig. 13

Press to return to index

Fig. 15

Fig. 15) Open the door and mark the centre of the door on the ceiling (E).

Fig. 16

Insert the expansion plugs in the architrave (V) and raise the

guide (2). Fix the guide bracket (3) with two screws (4) by

using the washers (5). Lift the automatic system (2).

Fig. 17

Lift the guide (3) and align the bracket for the suspension to

the ceiling. The position must be in zone B, where B is 0 to 600

mm. long. Carry out two holes Ø 10x65 mm. and insert two

expansion plugs S10 (1) and fix tight the two screws 8x60 (2)

by using the two washers (2).

Fig. 16

Fig. 17

Fig. 14) Drill two holes (D) Æ 10 in the lintel or in the ceiling, 74 mm to the right and to the left of

the centre of the door (C).

Fig. 14

Fig. 18

Fix (3) the door corner fitting (1) onto the rod, in a longitudinal

direction with respect to the position of the motor. Unlock the

motor by pulling the manual release (N).

ZN SERIES ACTUATOR

Press to return to index

Emergency release

1. Lower the red lever on the motor (N) to release it and open the horizontally pivoted door manually (see figure 19/ZN).

2. Install the manual release in the door using the appropriate bracket, which must be fixed in the handle of the door, secure it with

the cable clamp (type ZN24), and insert the cable in place of the red motor release lever.

3. With ELVOX kit type ZN23 it is possible to release the automated closure system from outside the door.

ZN SERIES ACTUATOR

Fig. 19) Regolare il fine corsa (4) spostandolo completamente verso il motore.

Move the motor (1) all the way forwards (3) with the rod. Align the door corner fitting (5)

with the centre of the doorway, drilling four holes ø5mm. Adjust the limit switch (4), mov-

ing it all the way up to the motor.

Fig. 19

max 30°

Fig. 20

Fig. 20) Move the limit switch (1) up to point (2), that is to say all the

way back. Open the door (3) manually from the side. Once

open it is possible to adjust the open limit switch.

N.B. If the sectional door does not close completely use the

adjustable bracket type ZN27.

Emergency release

- Pull the red lever in the motor (N) downwards once; so that the motor unlocks and the door can be opened manually (see figure

19).

- To install the manual release inside the door, fix it by means of the relative bracket inside the door handle, secure by means of a

cable clamp (type.ZN24), and position the cable in place of the red lever (W) of the motor release.

- If the area closed off by the garage door is not accessible from inside and the control needs to be released manually, an external

release device must be installed on the handle using the Elvox kit type ZN23.

Operation of external release device type.ZN23

The garage door can also be opened manually from the outside by means of the

motor release. For this purpose, insert key 1 (A) in cylinder 2 (Fig. a), turn it clockwi-

se and remove with lock cylinder (B). At the same time cable 6 will release the motor.

External release device assembly

According to the type of garage door, choose one of the assembly options shown in

fig. b.

Fig. a

Drill a hole (diam. 20 mm) to insert the cylinder of lock 2 (fig.c) at approx. 60 cm from

the upper edge of the garage door.

If necessary, enlarge the hole from inside for threaded bushing 3 (diam. 23 mm; see

fig.c), and proceed with assembly.

In the case of sheet steel doors, drill four 4 mm holes for the washer (on a circumfe-

rence of 26 mm.), (see fig. b letter F).

Now tie cable 6 (fig.c ) onto ring 7 (fig.c) of the lock cylinder. Tie the other end of the

cable to motor release cable 8 (fig.a.).

Avoid tensioning the cord.

Press to return to index

Fig. 21/ZN

Fig. 22/ZN

Installing the variable sectional door mounting type ZN27

Loosen the two screws and remove the U shaped section of the door mounting. Fasten to the sectional door mounting as illustrated.

Fig. 21/ZN: Set the sectional door mounting to the right length A, fix in place with 2 metal screws B and fasten to the upper section

of the door (X). Slide the boomerang C into the connecting rod D (U Section) and connect with 2 M10x25 bolts and nuts.

Fig. 22/ZN: If necessary shorten the connecting rod by sawing off accordingly and connect directly to the sectional door mounting.

ZN SERIES ACTUATOR

Fig. c

Fig. b

Press to return to index

ZN SERIES ACTUATOR

INSTRUCTIONS FOR THE CURVED ARM

For counterbalance up and over doors, remove approximately 3-8 Kg, according to the weight of the door. For spring up and over

doors, reduce the tension in the spring by 3-5 cm, according to the weight of the door.

Assembly:

1. Remove the door lock lever (1). Determine the point of maximum aperture of the swing device. Position the track 10-12 mm

above the door.

2. Position the curve (2) vertically and at the centre of the door, and bring it up to the top edge of the swing device (3). On the angle

irons (4) supporting the curve, position the holes so as to allow stable fixing to the door frame (5).

3. Screw the curve to the swing device frame. Install an emergency release (6) and move it so that the end of the curved arm (12)

is located at the hole in the motor block. Always leave a distance of almost 50 mm (see drawing).

If required, after removing the screws (7), modify the length in 25 mm steps (8), after first unlocking the spacer track (9).

Do not connect the curved arm to the motor yet!

4. Move the motor back (end part of the track).

5. Open the up and over device manually. Push the curved arm backwards.

6. Remove the lock nut (10) connecting the track to the ceiling. Move the track by an amount (see arrow) sufficient that the hole in

the motor (11) coincides with the hole in the curved arm. Connect the curved arm to the motor. Adjust the power and movement

as described in the assembly instructions.

Press to return to index

Fig. 23/ZN Install the box containing the control unit, preferably

close to the garage exit door, so as to use the existing

power socket. This socket must be installed at a mini-

mum height of 1.6 metres above floor level.

The cable connecting the control unit and the C-track

has a maximum length of 6900 mm, and it must not be

extended!

Fig. 24/ZN To connect the cable in the control unit, unfasten screw

(1) and remove the cover over the box courtesy light (2).

The power supply to the control unit must not be turned

on yet.

Fig. 25/ZN Extract the electronic card (1) by pulling it upwards, and

disconnect it from the terminal board (2). Connect the

two wires from the motor power supply cable to the ter-

minal board; the wire with number 3 printed on it must

be connected to terminal 3, and the one with number 4

printed on it must be connected to terminal 4.

Fig. 26/ZN Fix the power supply cable firmly to the rear side of the

box.

Fig. 27/ZN Mark the fixing points horizontal to the wall, at a distan-

ce of 110 mm. Drill two holes (ø6x40 mm depth). Fix

the box to the wall using two screws 4x50 (3) and two

plugs S6 (2).

ELECTRICAL INSTALLATION

ZN SERIES ACTUATOR

Programming the remote controls

Under no circumstances modify the length of the aerial cable!

Remove the elastic from around the red aerial cable, pushing it

upward (7) through the rear wall of the box, extracting it and fixing it

(Fig. 26/ZN).

Radio control code storage

Press and keep pressed the push-button present on the circuit

board for at least 3 seconds until the led turns on.

Now release the push-button and send the code from a radio con-

trol. If the operation was successful, the led turns off.

Cancellation of all codes stored

Press and keep pressed the push-button present on the circuit

board for at least 3 seconds until the led turns on. Release the

push-buttons and press it again. The les starts flashing. Press again

and keep pressed the push-button for at least 3 seconds until the led

flashes with a higher frequency and finally the led turns off.

N.B. The circuit board, with the 433 MHz receiver, can store up to

30 different radio control codes.

Adjusting applied force

The force required to open the door is adjusted automatically by the electronic card while it carries out self-regulation the first two

times the door is opened. During this operation, the courtesy light (2) will flash.

After turning the power supply to the control unit on, press the red button (6) fig. 26/ZN.

Open and close the door twice, during this operation the maximum values for the force to be applied to the door are read automati-

cally by the microprocessor, and at the end of the operation the light (2) will stop flashing. After adjustment, use the remote control

or the red button (6) to operate the automatic door.

Deleting force values

1. Turn the control unit power supply off

2. Remove the screw and take the cover off the courtesy light in the box.

3. Press and hold the function button (3) T1 for three seconds, until the light (2) starts to flash, then release button T1 and the force

values will be deleted automatically.

Storing new force values

1. When the lamp (2) flashes the new force values must be stored. Press the button (6) in the box once, the door will open without

stopping until it reaches the limit switch. Once it has stopped, press the button (6) again and the door will close until it is comple-

tely shut.

2. Press the button (6) again: the door will open until it is completely open.

3. The force values both for opening and closing have now been read, and the light (2) will stop flashing.

4) Once the force has been regulated, fasten down the courtesy light cover in the box.

STARTING UP

Fig. 24/ZN

Fig. 23/ZN

Fig. 25/ZN

Fig. 28/ZN

Fig. 26/ZN

Fig. 27/ZN

Press to return to index

ZN SERIES ACTUATOR

CONTROL UNIT

Description of control unit terminals

Fine wire fuses

6 DIL switches

Radio receiver unit

PROGRAMMING THE SWITCHES

Switch Posit. Function / Reaction

Reaction to security connected in input 1+2 of the accessory terminal block during the opening phase (example: photocell interruption)

1 OFF no reaction during opening

ON stop during opening

1+2 input operation for the accessory terminal block.

2 OFF NC security input (example: photocell)

ON NO input for 2nd actuator (example: partial opening)

Reaction to security connected to input 1+2 of the accessory terminal block during the closing phase (example: photocell interrup-

tion).

3 OFF partial inversion during the closing phase

complete inversion during the closing phase (re-opening).

5+6 output operation of the accessory terminal block, for flashing light.

4 OFF Flashing impulse for flashing light

ON Indicator LED for the door state:

- Fixed lighted with open door

- switched off with door close

5 OFF pre-flashing deactivated

ON 3'' pre-flashing

Backjump (only during the closing phase)

To reduce the stress on the door and automation mechanics during the total closing phase, the automation moves shortly in the ope-

ning direction.

6 OFF deactivated

ON activated

Automatic closing

7 OFF deactivated

ON automatic closing after 1 minute (if 8 OFF).

(if 7 ON)OFF automatic closing after 1 minute

automatic closing after 5'' from the photocell interruption.

When the horizontally pivoted door is open, the automatic closure function disables the radio controlled or push-button operated clo-

sure function.

Terminal

Terminal block connection for the circuit board

Terminal 1-2: transformer

Terminal 3: guide with C shaped section

Terminal 4: chain

Terminals 5-6:

wall push-button connection, free on automation.

Photocell connection

Terminal 1÷ 2 security connection, only if Switch 2 in OFF position

Terminal 3 ÷ 4 24V D.C. connection max 0,1A

terminal 3: 24V D.C.

terminal 4: earth

VAC

COM

AP/CH

Terminal:

1-2) Safety connection (LS or DW)

1: signal 2: earth

3-4) Output +24V, max. 1A, for example powering a photocell

3: +24V 4: earth

5-6) Connecting to flashing light 24V, max 1A

Fuse:

1 fuses 1AT/250V; 5x20 mm

24V output

]

Transformer power input

]

Open contact for optional external command.

]

C-track power supply

Press to return to index

ZN SERIES ACTUATOR

Flashing light connection:

Terminal 5 ÷ 6 24V D.C. connection (max 34V) not adjusted, max

Cleaning the chain and the guide

If the chain (7) or the guide (8) are very dirty, clean them with a

clean cloth.

Every year lubricate slightly the chain with conductive oil.

Do not use grease! N.B. Use only conductive oil.

1- Fuse for flashing light connec-

tion, terminals 5 ÷ 6, 1A with

delayed action

Replacing the switchboard lamp

- Remove the electrical plug from the socket

- Unfasten the screws (1)

- Remove the transparent cover (2)

- Turn the lamp (3) leftwards and remove it.

- Insert the new lamp (24V, 21W, BA 15s type) and turn it rightwards until the end.

Replacing the switchboard fuses

- Remove the electrical plug from the socket

- Unfasten the screw (1)

- Remove the transparent cover (2)

- Pull off the control circuit board (3)

- Replace the faulty fuse. All fuses are 1A delayed

MAINTENANCE

Before carrying out any cleaning or maintenance operations on the motor, switch off the power by means of the appropriate magne-

tic/thermal switch upstream of the control unit and disconnect the back-up battery.

If the power supply is needed to carry out operational checks, disable all control devices (radio controls, keypads, etc.) except for

the device used by the maintenance technician. In general, the ZN10 electromechanical actuator requires little maintenance, but cor-

rect operation also depends on the condition of the door.

Both ordinary and extraordinary maintenance must be carried out by a specialised technician.

Routine maintenance:

Each of the following operations must be carried out on an “as necessary” or at least once every 6 months basis.

- If the chain is very dirty, clean it with a cloth.

- Lubricate the track with "conductive" oil

- Check that all the screws are tight, and if necessary tighten them.

- Check spring compensation and the up and over door mechanism.

Automatic system:

Check that all the safety devices (photocells, pneumatic stops, etc.) are operating properly, at the times and in the manner descri-

bed by the manufacturer (see safety instructions).

Extraordinary maintenance:

Extraordinary maintenance operations are not anticipated, however if major work involving the mechanical parts is necessary, it is

advised to remove the actuator for repair (by specialised personnel).

Press to return to index

ZN SERIES ACTUATOR

Fig. 29/ZN

Fig. 30/ZN

SAFETY KIT FOR PEDESTRIAN DOOR

Type ZN26

To prevent entrapment between the horizontally pivoted door and the pedestrian door, it is necessary to install a microswitch so that

the automated closure system does not start operating when the pedestrian door is open.

TECHNICAL SPECIFICATIONS

- Microswitch contacts: NO-NC 230V A.C.

- Protection degree: IP66

INSTALLATION

1. Remove the motor cover.

2. Drill a hole of 98 ÷ 100 mm, and insert the cable supplied (see Fig. 29/ZN)

3. Remove connector two Faston coupling No. 5 (see Fig. 30/ZN), connect the device (A) between connector 5a and coupling No. 5.

To insulate the connection in the Faston coupling and in the connector, use the sheath supplied with the cable.

4. Refit the motor cover.

5. Remove the screw and the cover of device (A), connect the two conductors in the NO contact (NC with the door closed).

Press to return to index

ZN SERIES ACTUATOR

MR2

- + Vac Vac

MR1 MR3

124356

24V c.a.

ZN range automatic gate system

circuit board

Battery 2X12V

Transformer

Mains

230V ~

Battery charge Type ZNB1

INSTALLATION

- Disconnect the supply voltage

- Carry out connections to the electronic control circuit board as indicated in the fig. 31/ZN

Check the state of the battery charge with a multimeter (Tester) every 6 months. To obtain the maximum battery performances carry

out three charge/discharge cycles.

In case of replacement use original battery and recycle the others according to the norms in force (by specialized personnel).

In any case it is advised to replace the battery every 24 months.

Fig. 31/ZN

KIT OF BACK-UP BATTERY FOR AUTOMATIC GATE SYSTEMS ZN SERIES

Type ZNB1

GENERAL FEATURES

Kit of back-up battery, type ZNB1 with 4-Module DIN housing, for automatic gate systems for ZN range sectional doors and hori-

zontally pivoted spring or counterweighted doors. In case of mains failure the back-up battery ensures a sufficient automation auto-

nomy. If the battery is flat the motor can be manually released by pulling down the red lever.

115

134

Dimensions (mm)

TECHNICAL SPECIFICATIONS

Supply voltage: 26,6 V D.C.

Power : 120mA

Type of battery: 2x12V 3,2Ah

Battery recharge time: to Temp. 20° C: 24 Hrs (in stand-by)

16 Hrs

(for cyclical operation)

Operating temperature: 0° ÷ 40° C

Press to return to index

ZN SERIES ACTUATOR

PERIODICAL CHECK UP

Check the correct safety device operation periodically or in any case once a year (see ZH 1/494 April, 1989).

Monthly check up the correct operation of the safety devices, which are sensitive to pressure (for example switch trim). See EN60335-2-95.

Check up Reaction

Yes/No

Possible cause Solution

Disconnecting the

motive-power

Stop a door leaf with

a 50 mm high object

during the door

closing phase.

Emergency release

Follow instructions

described in para-

graph "Emergency

release"

Safety switch trim,

if installed

Open/close the door

by activating the

switch trim simulta-

neously.

Photocell, if instal-

led

Open/close the door

by interrupting

the photocell simulta-

neously.

- Leave all programmings unchanged

- Reduce the motive-power tolerance. Turn trim-

mer leftwards until the check up has positive

result. Open the door and close it completely

twice keeping it under control. See paragraph:

"Maximum motive-power adjustment ".

- Adjust the door, contact qualified personnel!

- Repair the emergency release.

- Check the door operation, see instructions:

"Door maintenance ".

- Check the cable, re-fasten the terminals.

- Reposition the switch

- Deactivate the installation and exclude the

reactivation. Contact the service personnel.

- Check the cable, re-fasten the terminals.

- Reposition the switch

- Clean the photocell

- Reposition the photocell

- Deactivate the installation and exclude the

reactivation.

- Contact the service personnel.

When the auto-

mation faces the

the object, it

inverts the motion

The door should

be easily opened

and closed

manually (the

door is balanced).

Door reaction

according to

programming of

switch 1, 2 or 3.

Door reaction

according to

programming of

switch 1, 2 or 3.

- The motive-power disconnection

works without limits.

- Trimmer on right limit stop.

Motive-power tolerance pro-

gramming too high.

- The door is not correctly adju-

sted.

- The emergency release works

properly.

- The emergency release is faulty.

- The door got stuck.

- The security switch trim operates

correctly.

- Cable broken, loosened terminal.

- Switch displaced

- Faulty switch trim

- The photocell works correctly.

- Broken cable, loosened terminal

- Switch displaced

- Dirty photocell

- Photocell displaced (bent sup-

port)

- Faulty photocell

Yes

TROUBLESHOOTING- DIAGNOSTIC TABLE OF COMMON PROBLEMS

Faults in the garage door operator can be eliminated by following the instructions given in the table below. If you are unable to solve

the problem, please contact your dealer.

Problem Cause(s) Solution(s)

The door cannot be moved either

manually or electrically.

The automatic device does not work and

there is no light.

The automatic device does not work when

the remote control is used.

The door stops while closing, moves back

approximately 10 cm and then stops

again.

The door stops while opening.

The door can only be used if the button is

pressed, and the internal light flashes.

No light can be seen during opening and

closing of the door.

The speed changes during the opening

and the closing phase.

- Enable the emergency release (N) and

open the door manually.

See paragraph "Emergency release".

- Check using another electrical device, for

example a tester.

- Replace the fuse.

- Replace the battery

- Code the remote control. See paragraph

"Coding the remote control".

- Remove the obstacle and open the door

completely

- Adjust the limit switch again.

- Remove the obstacle and close the door

completely

- Adjust the limit switch again.

- Remove the obstacle, then move the

door to the final position, and the opera-

tor will once again work normally.

- Replace the bulb.

- Normal slowing down

- Clean the guide and lubricate it again

- Tighten the chain

- There is a power cut

- The fuse in the garage power circuit has

blown

- The remote control battery is low.

- The remote control has not been cor-

rectly coded.

- Forced stoppage has been triggered due

to the presence of an obstacle.

- Limit switch badly adjusted.

- Forced stoppage has been triggered due

to the presence of an obstacle.

- Limit switch badly adjusted.

- Forced stoppage has been triggered due

to the presence of an obstacle.

- Blown lamp

- The automation starts slowly and then

accelerates.

- The chain guide is dirty

- The chain guide has been lubricated

with the wrong type of oil

- Chain not correctly stretched.

Press to return to index

Elvox ZKN2 User manual

Brand: Elvox

Model: ZKN2

Category: Garage Door Opener

Type: User manual

This manual is also suitable for

Download PDF

report

Elvox ZKN2 User manual

This manual is also suitable for

Elvox ZKN2 User manual

Related papers

Other documents