Zenith Sentry 2 Z25X22 Operating Manual & Warranty

Brand: Zenith

Model: Sentry 2 Z25X22

Category: LCD TVs

Type: Operating Manual & Warranty

This manual is also suitable for

Return the

Product

Registration

Card and your

TV could be

FREE/

THEQUALITY GOES IN BEFORETHE NAMI ] GOES ON

;pana:

nque

SAFETY WARNINGS

WARNING

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO

USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user

to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user :tothe presence of'

important operating and maintenance (servicing) instructions in the literature acc3mpanying the

appliance.

SAFETY TIPS

REGULA TORY INFORMATION

Refer to the "Important Safety Instructions" section of this

operating guide for important safety considerations.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT

EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE TV SYSTEM

INSTALLER

This reminder is provided to call the cable TV system

installer's attention to Article 820-40 of the National

Electrical Code (U.S.A.). The code provides guidelines for

proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the

building, as close to the point of the cable entry as practical.

POWER-CORD POLARIZATION

This product is equipped with a polarized alternating-

current lilaeplug (a plug having one blade wider than the other).

As a safety feature, this plug will fit into the power outlet

only one way. If you are unable to insert the plug fully into

the outlet, txy reversing the plug. If the plug still fails to fit,

contact your electrician to replace your obsolete outlet. Do

not defeat the safety purpose of the polarized plug.

Caution

To prevent electric shock, match wide blade of plug to

wide slot; fully insert.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection againsl: harmful interfere.nce in a

residential insltallation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause

harmful interfierence to radio communications However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference Io radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate t]aereceiving antenna.

• Increas,e the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receive:r is connected.

• Consult the dealer or an experienced radio/TV

technician.

CAUTION: Do not attempt to modify this product in any

way without written authorization from Zenith Electronics

Corporation. U'nauthorized modification could void the

user's authority to operate this product.

Attention

Pour 6viter les chocs 61ectriques, introduire la lame la plus

large de la fiche dans la borne correspondante de la prise et

pousser jusqu'au fond.

ZTVWARN

• IMPORTANT SAFETY INSTRUCTIONS **

Your product has been manufactured and tested with your safety in mind. However, improper use can :result in potential electrical

shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the

following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this section of the operating guide can help you get many years of enjoyment and

sa_Feoperation from your new product.

1. Read Instructions

Read all the safety and operating instructions

before operating the product.

2. Follow Instructions

Follow all operating and use instructions.

3. Retain Instructions

Keep the safety and operating instructions for

future reference.

4. Heed Warnings

Follow all warnings on the product and in the

operating instructions.

5. Cleaning

Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water -- for example,

near a bath tub, washbowl, kitchen sink, laundry

tub, in a wet basement, or near a swimming pool.

7. Accessories

Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may

fall, causing serious injury to a child or adult, and

serious damage to the product. Use only with a

cart, stand, tripod, bracket, or table recommended

by the manufacturer or sold with the product. Any

mounting of the product should follow the manufac-

turer's instructions, and should use a mounting

accessory recommended by the manufacturer.

8. Transporting Product

Move product and cart combinations with care.

Quick g'tops, excessive force, and uneven surfaces

may cause the product and cart combination to over-

turn.

PORTABLE CART WARNING

9. Attachments

Do not use attachments not recommended by the

product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet must n_t be blocked

or covered. They are provided for ventiilation, to

ensure reliable operation, and to protect from over-

heating. Never block the openings by placing the

produdt on a bed, sofa, rug, or other similar surface.

This product should not be placed in a built-in

installation such as a bookcase or rack unles:_ proper

ventilation is provided or the manufacturer's

instructions have been adhered to.

11, Power Sources

Operate this product only from the type of power

source indicated on the marking label. If you are

not sure of the type of power supply to your home,

consult your product dealer or local power com-

pany. For products intend _d to operate from battery

power or other sources, refer to the operating

instructions.

12. Line-Cord Polarization

This product is equipped with a polarized alternat-

ing-current line plug (a plug having one blade

wider than the other). As a safety feature, this plug

will fit into the power outlet only one way. If you

are unable to insert the phJg fully into the outlet,

try reversing the plug. If the plug still fails to fit,

contact your electrician tc replace your obsolete

outlet. Do not defeat the safety purpose of the polar-

ized plug.

13. Power-Cord Protection

Route power-supply cords so that they are not

likely to be walked on or pinched by items placed

upon or against them, paying particular attention to

cords at plugs, convenie, nce receptacles, and the

point where they exit frc_m the product.

oo°

ZENGSAFE nl

IMPORTANT SAFETY. INSTRUCTIONS

114. Outdoor Antenna Grounding

• If an outside antenna or cable system is connected

to the product, be sure the antenna or cable system

is grounded so as to provide some protection

against voltage surges and built-up static charges.

Article 810 of the National Electrical Code

(U.S.A.), ANSI/NFPA 70 provides information

with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding con-

ductors, location, of antenna-discharge unit,

connection to grounding electrodes, and require-

ments fer the grounding electrode.

EXAMPLE OF GROUNDING ACCORDING TO

NATIONAL ELECTRICAL CODE INSTRUCTIONS

Antennfi Lead in Wire

J' Ground

_ Clamp_ _ ! Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductors

(NEC Section 810-21) ,

I EleCtl_i:luipment

I,........._.....__ll __ Ground ClampsElectrode System (NEC

Power Service Grounding

Art 250, Part H)

NEC - NATIONAL ELECTRICAL CODE

15. Lightning

For added protection for this product (receiver) dur-

ing a lightning storm, or when it is left unattended

and unused for long periods of time, unplug it from

the wall outlet and disconnect the antenna or cable

system. This will prevent damage to the product

due to lightning and power-line surges.

I6.. Power Lines

An outside antenna system should not be located in

the vicinity of overhead power lines or other elec-

tric light or power circuits, or where it can fall into

such power lines or circuits. When installing an out-

side antenna system, take extreme care to keep

from touching such power lines or circuits, as

contact with them might be fatal.

1.7. Overloading

Do not overload wall outlets and extension cords,

as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never pttsh objects of a_ly kind into this product

through openings, as I:h_;y may touch dangerous

voltage points or short-out parts that could result in

a fire or electric shock. Never spill liquid of any

kind on the product.

19. Servicing

Do not attempt to service this product yourself, as

opening or removing covers may expose you to dan-

gerous voltage or other hazards. Refer al_ servicing

to qualifiied service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer

servicing: tO qualified service personnel under the

following conditions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen,

into the product.

c. If the product has been exposed to rain or water.

d. If the product doe,; not operate normally by fol-

lowing the operating instructions. Adjust only

those controls that are covered by the operating

instructions; improper adjustment of other con-

trols may result in damage and will often re-

quire extensive work by a qualified te,chnician

to restore the product to its normal operation.

e. If the product has been dropped or the cabinet

has been damaged

f. If the product exhibits a distinct change in per-

formance.

21. Replacement Parts

When replacement parts are required, be sure the

service technician has u:;ed replacement parts

specified by the manufacturer or that have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or

other hazards.

22, Safety Check

Upon completion of a_ay service or re?airs to this

product, ask the service technician to perform

safety checks to determine that the product is in

proper operating condition.

23. Wall or Ceiling Mount_ing

Mount the product to a wall or ceiling only as

recommended by the manufacturer.

24. Heat

Keep the product away from heat sources such as

radiators, heat registers, stoves, or other products

(including amplifiers) t17at produce heat.

2ENGSAFE iv

; : .., - . •

CONTENTS '.....

SAFETY WARNINGS.. i .............................. ii

I3ffPORTANT SAFETY INSTRUCTIONS ............... iii

TYPICAL CONNECTIONS FOR YOUR TV

Connection Center ......................... : ....... 1--1

Ci_oosing the Connection Diagram That's Right for You... 1--1

Diagram #1. Basic Connection to TV .................. 1--2

Diagram #2. Connections to TV with VCR .............. 1--3

Diagram #3. Audio Amplifier Connection to TV ......... 1----4

QUICK SETUP GUIDE

Connect the Power ................................. 2--1

Install the Batteries into the Remote ................... 2--1

(lq'.equired) Use Auto Program... ...................... 2--1

Set the Clock ...................................... 2--2

Use Other Menu Options ............................ 2--2

SETUP MENU

Menu Operation ................................... 3--1

Using Add/Del/Surf .............. ............ ...... 3--2

Using Channel Labels ............................... 3--3

Timer Setup: Sleep Timer . .......................... 3--3

Timer Setup: On/Off Timer .......................... 3--3

Using Parental Control .............................. 3--4

Using Auto Demo .................................. 3--4 -

AUDIO MENU

Menu Operation .................................... 4---1

VIDEO MENU

Menu Operation .................................. 5--I

SOURCE MENU

Menu Operation ................................... 6----1

GET TO KNOW YOUR REMC_TE (MBR3447)

Simple Product Operation ........................... 7--1

Programming Your Remote .......................... 7 2

Auto Find Option (Alternate Proglamming Method) ...... 7 3

Operating Code.,; by Brand Name ...................... 7----4

TV Operations .................................... 7 5

Preset Codes for Zenith Producls ...................... 7---6

Special Features ................................ ... 7--7

MAINTENANCE AND TROUBLESHOOTING

Caring for Your TV ................................ 8 1

Extended Absence ................................. 8--1

"IV Picture Interference ............................. 8 1

Video Games and Other Fixed Pattern Display Caution .... 8 1

Record Model Number of Your TV .................... 8---1

Before Calling for Service ........................... 8 2

ACCESSORIES FOR YOUR TV

REPLACEMI?NT PRODUCT REGISTRATION CARD

AVISO PARA NUESTROS CLIENTES DE HABLA H!SPANA

ZENITH QUESTIONNAIRE

YOUR ZENrI'H WARRANTY

FEATURES PROVIDED WITH YOUR TV

This operating guide describes a family of TV models. Not all models have all of the features described in this guide. Most models

include the following features:

,, On-Screen Menus Accessed By Remote or TV Controls • Sleep Timer and On/Off Timer

• Multi-Brand Programmable Remote • Automatic Channel Programming

• Parental Corltrol • English/Spanish/French On-S :reen Menus

• MTS Stereo • Audio/Video ]Input Jacks for Stereo VCR

• Front Channel Surround Sound • 181 Channel Tuning, STD/HRC/ICC Bands

• Closed Caption and Text Modes . Antenna/Cable Input Jack

• Channe! Labels for Easy Channel Identification . Variable Audio Output Jacks

(Design and specifications are subject to change without prior notification.)

32(_,5-O V

' -TYPICAL CONNECTIONS, FOR YOOR TV

• ' _ ENTER .... "

CONNECTION C -'

SPEAKER EXT/INT SWITCH

Select EXT (external) to remove [[_ _'

sound from the TV's speaker(s).

Select INT (internal) to hearsound

•from the TV's speaker(s).

AUX (Auxiliary) INPUT IIII

Jacksf°rAudi°andVide°(A/V t

connections to your Tv from

video equipment like a VCR

Make A/V connections to these III TV BACK

jacks in order to hear stereo sound

from your video equipment.

_k Turn off power or unplug TV

before making any connection.

/. ?.

VA RIABLE AUDIO OUTPUT

Connect a stereo amplifier to these

jacks to listen to your 'IV through

your stereo system. Do not connect

speakers directly to these jacks. •

Variable audio ou:Lput is always

pre_ent regardless of the position

of the SPEAKER EXT/INT switch.

VI[F-UHF/CABLE

Atlach your antenna, cable-TV

,;ys tem, or VCR to this jack.

CHOOSING THE CONNECTION DIAGRAM THAT'S RIGHT FOR YOU

Find your type of equipment by matching the items shown in this chart. Then refer to the last colum a to choose the Diagram

Number you need to make the proper connections for your system.

ANTENNA

;DIRECT I : CABLE

STEREO

VARIABLE DIAGRAM

'_ 3

s:os-o 1_ 1

i i ITYPICALICONNECTIONS FOR YOURTV i:i

, . . . ,

DIAGRAM #1.BASIC CONNECTION TO TV " " '

~ .

Cable TV Cable TV Antenna

Wall Jack Wall Jack

CH 3/4

toTV

TVBACK

Flat Wire I]

(300 ohm) u

o. .... -.

3oorisohm |

Adaptor I

Round Wire

(75 ohm)

Note: Cables are not

supplied with "IV.

With Cable Box

D Select cable box outputchannel

(usually channel 3 or 4) at TV.

rn Select channels for viewing at

cable box.

Without Cable Box

Select channel,,; for

viewing at TV.

_'2os-o 1 -- 2

TYPICAL CONNECTIONS IFOR

*DIAGRAM #2. CONNECTIONS TO "IV WITH VCR

ANTENNA VCR

TON

Basic Connection X

to v \_

'I:

¥ ,

_r,,-_.. _ _ I

® :

i ',, "'-. m

_mImmJ,,imim_ €@

A/V Connections to TV

You must make this Audio/Video connection in order to

hear stereo sound from your VCR during tape playback.

l Operating YOur_ Usi ng__ FromVCR (Aux Input)

121Select Video for the viewing source as the Main Source option.

See the "Source Menu" section fordetails.

S--_ectd_nnels for viewing at VCR, or play a tape in the VCR.

Note: Refer to operating guide provided with your VCR for

VCR operations.

-: : : Operating Your TVUsing Basic Connection(As Shown Above)

With Cable Box Without Cable Box

El Select VCR output channel (usually channel 3 or 4)

at TV.

rn Select channels for viewing at cable box.

O Select VCR output channel (usually channel 3 or 4) at

TV.

El Select cable box output channel (usually channel 3 or

4) at VCR.-

Cl Select channels for viewing at cable box.

Note: TV/VCR switch may be labeled TV/Video on some VCRs and remotes.

TV/VCR

Switch on VCR

(Use channel

selector in TV)

VCR

(Use channel

selector in VCR)

Select channels for viewing at TV.

Select VCR output :hannel (usually charmel 3 or 4) at

TV.

Select channels for viewing at VCR,

3205-O 1 --3

, '_TYPiCAL CONNECTIONS IFOR YOUR TV

.m. I i

DIAGRAM #3. AUDIO AMPLIFIER coNNEcTION TO TV

To listen to your TV through your sound system, connect the stereo amplifier to the VARIABLE AUDIO OUTPUT jacks on the TV as

shown.

_" ..... _1111_ ' IAUXINPU T

...._ _ __,_

j "

Note: Cables arenot

supplied with TV.

Do not connect speaker(s)

directly to the VARIABLE

AUDIO OUTPUT jacks.

To Speakers

SPKR o uTPL_NI_

Back of your

Stereo Amplifier.

Optional

Customer-

Provided

Scund

System

I J "

ANTI_NNA

CABLE

Speaker sWitch : TV Speakers t7 Soun_dSystem 1

EXT = External Off / Sound Available

INT = Internal ] On __-[/ Sound Available _1

Note: Variable audio is TV sound that you can adjust using your TV Volume

Up/Down control to change your sound system's volume level.

32o5-0 1 -- 4

• I I

il. cONNECT THE POWER " *

! ?QUICKSETUP GUIDE • ii; : .

"r_,

I . " J •

._-TER you have connected the necessary cable(s)to the

jacks on the back of the TV, plug your TV's power cord into a

standard AC power outlet for 120 volt, 60Hz. AC current.

Make sure you do not plug the TV into an outlet controlled by

a switch.

Turn on the TV by using the On/Off switch on the TV.

.,q

2. INSTALL THE BATTERIES INTO THE REMOTE

Install the batteries that are provided with your remote.

The remote cc)mes set with Zenith codes• If you'd like to use the remote to operate c)ther brands of equipment, you will need to pro-

gram the codes for that equipment into the remote.

1. Open the battery compartment by pressing in on the tab and lift-

ing the cover off.

2. Place the batteries into the compartment, matching plus with

plus (+ with +) and minus with minus (- with -).

3. Replace the cover.

Pushtabin

Use 2 size AAA batteries

3. (Required) USE AUTO PROGRAM

The firsttime you turn on your TV, use Auto Programto find all

available channels.

1. Press MENU repeatedly to view the Setup Menu.

2. Select Auto Program using the Up/Down arrows.

3. Use the I,eft/Right arrows to advance to the next menu.

4. Select OFF AIR ANTENNA if you have an antenna or CABLE

TV if you have cable TV.

5. Use theLeft/Right arrows to begin the channel search.

_ etupMenu

Auto Program

Add/Del/Surf

Oh. Labels

C],ock Set

Timer Setup

Parental CII

Caption/Text

Language

A_uto Demo

l'<l_ To Program ]

Setup Menu with Aulo Program Highlighted

__ Ch Is Founo ets Four_

These typical screens appear while

the channel search is in process.

3205-0

2ml

QUICK SETUP GUIDE-

4. SET THE cLOCK

i i ii_iii,iiiiiiiilli ! ?iilToset theCJoek!iiii_i_iiiii!i_ii!ii_ilililiiifill!iiiii_iiiiiiiiiii_!_iii!i!iiiii!iiiii_i¸

1. Press MENU repeatedly to view the Setup Menu.

2. Select Clock Set using the Up/Down arrows,

3. Use the numbers on your remote to enter the time and press

TIMER to select AM or PM. (You can also use the Left/Right

arrows to set the clock to the current time.)

4, Press QUIT to remove the menu from view.

_ etupMenu

Auto Program

Add/DeVSurf

Oh. Labels

Clock Set i]

Timer Setup

Parental Ctl

Caption/Text

Language

Auto Demo

[ 10:30 AM÷_

Setup Menu with Clock Se t Highlighted

5. USE OTHER MENU OPTIONS

_ etupMenu

Auto Program [

Add/Del/Surf

Ch. Labels

Clock: Set

Timer Setup

Parental Ctl

Caption/Text

Language

Auto Demo

Press

_ _ Audio

IBass I

Treble

Balance

Audio Mode

Surround J'

SoundRite

Press

111WaeoMenu

[Contrast ----]

Brightness

Color

-tint

Sharpness

Picture Pref

Press

_ ourceMenu

[Main Source

3205-o 2--2

MENU OPERATION

SETUP MENU ,.

[_ SetupMenu

[Auto Program

Add/Del/Surf

Ch. Labels

Clock Set

Timer Setup

Parental Ctl

Caption/Text

Language

Auto Demo

I'1• To Program ]

* These options are not available if you choose

VIDEO for Source Menu Options.

• Menu Operation

• : ::: •

1. Press MENU repeatedly to choose Setup Menu.

2. Press an Up/Down arrow repeatedly to select ;m option.

3. Press a Left/Right arrow repeatedly toadjust an option.

4. Press QUIT to remove a menu from view, or 'wait a few

seconds and the menu will di:;appear.

Auto Program

Add/Del/Surf

Channel Labels

Clock Set

Timer Setup

Finds and stores active channels to use with the CHANNEL Up/Down arrows.

Creates a list of favorite channels to use with CHANNEL UpfDown arrows.

Assigns a network/station label, name, or call letters to channels, Example: If you assign ABC to channel 13,

then ABC v¢ill appear when you select channel 13.

Sets the TV's clock to the current time.

Note: The clock in the TV must be set before you can use the timers.

1. Sets the TV's Sleep Timer and On/Off Timer.

2. The Sleep Timer programs the TV to turnoff after a period i'rom 15 minutes up to 4 hours.

3. The On/Off Timer programs the TV to turn on and off at specific times.

Parental Ctl Blocks undesirable channels, including the VIDEO input source.

Caption/Text Displays closed captions or text when available on the selected channel. Options are: Off, Caption 1, Caption 2,

Caption 3, Caption 4, Text 1, Text 2, Text 3, and Text 4.

Language Selects English, Spanish, or French for on-screen menus.

Auto Demo Shows on-screen menus.

3z_5-o 3 -- 1

LISING ADD/DEL/SURF

' SETUP MENU

Point Remote at TV

SURF Button

CHANNEL Up/Down

These channels a::e selected by usiw

tile CHANNEL "Up/Down arrows.

C.hannels found by Auto Program

are set as "Added" channels.

1. Use the Up!Down arrows to choose

Add/Del/Surf.

2:. Select a chanael using the numbers

on the remote.

31. Use ihe Left!Right arrows to show

Added.

4. Press QUIT ::oremove the menu

from view.

To Delete Channels

These channels are not selected

when you use the CHANNEL

Up/Down arrows. Select them

directly by using lae numbers on the

remote,

1. Use the Up/I)own arrows to choose

Add/DO/Surf.

2. Select a channel using the numbers

on the remote.

3. Use the LeWRight arrows to shaw

Deleted.

4. Press QUIT to remove the menu

from view.

[Surf's Up! "_t

I No Surfing (_)1

"SURF" channels form a ilistof your favorite channels.

When the "SURF' mode isO:a, these are the only channels

that you'll see with the CHANNEL Up/Down arrows.

1. Use the Up/Down arrew_ to choose Add/Del/Surf.

2. Select a channel using the numbers on the,remote.

3. Use the Left/Right arrows to show Surf.

4. Repeat steps 2 and 3 to make your most frequently

watched channels "Surf" channels.

5. Press QUIT to remow: the menu from view.

To turn On "SURF," press SURF on the remote.

[Surf's Up! --_-] app, ars on the screen.

To turn off "SURF," press SURF again.

[ No Surfing (_] app{'ars on the screen.

3205-0 3 _ 2

• SETUP MENU '

USING CHANNEL LABELS ' ,- - -

1. Select Charmel Labels.

2. Select a channel using the numbers on the remote.

,'3. Use the Left/Right arrowg to see your choices until the desired

label appears, If you don't wish to create a channel label,

select the dashes (--).

_ etupMenu

Auto Program

Add/Del/Surf

[Ch. Labels

Clock Set

Timer Setup

Parental Ctl

Caption/Text

Language

Auto Demo

L Ch 2 CBS '-)

Setup Menu with Ch. Labels Highlighted

TIMER SETUP: Sleep Timer

The Sleep Timer programs the TV to turn off after a period from 15 minutes to 4 hours.

-' : From SetUp Menu : : Dim_t From Timer Button ,i

1. Make sure the TV's clock is set.

:2. Select Timer Setup and press a Left/Right

arrow to view the Timer Menu•

:3. Select Sleep Timer•

4. Press a Left/Right arrow repeatedly to set

how long the TV will remain on.

1. Press TIMER on the remote•

2. Press TIMER repeatedly to set how

long the TV will remain on.

Note: To cancel the Sleep Timer, turn off the TV or press TIMER repeatedly until

Off is showing•

Timer

On Time

Off Time

On/Off 11m.=r

:30

Sleep Timer set to turn TV

off in 30 minutes

TIMER SETUP: On/Off Timer

The On/Off Timer programs the TV to turn on and off at specific times.

: Set On/Off Timer : :

1. Make sure the TV's clock is set.

2. Select Timer Setup and press a Left/Right arrow to view the Timer Menu.

3. Select On Time and use the numbers on your remote to enter a time for the TV to

turn On. Press TIMER on the remote to select AM or PM.

4. Select Off Time and use the numbers on your remote to enter a time for the TV to

turn Off. Press TIMER on the remote to select AM or PM.

5. Select On/Off Timer and use a Left/Right arrow to show on.

6. Press QUIT on your remote to remove the menu from view.

Note: You must set an Off Time before you can set the On/Off Timer to On.

Z_mer

Sleep Timer

IOn/OffTirner ]

: 1"1:00 AM_I

I On ]

On/Of[' TiLmerset to turn TV On at

11:00 am and Off at 1:00 pm

32o5-o 3 _ 3

SETUP MENU '. '"

USING PARENTAL CONTROL

_::_: i:_:-_iToBlock Channels or the Video Input Source ....

11. Select Parental Ctl and press a Left/Right arrow to view the Parental

Control menu.

2. Select Block Ch, (channel).

:3. Use the numbers on the remote to enter a channel number and press a Left/Right

arrow to show Blocked.

4. Repeat steps 3 and 4 for each channel you want blocked.

!5. Select Block Video to block the video source input and press a Left/Right arrow

to show Source Blocked.

,S.

After you block all desired channels and/or the Video source, select Set

Hours and use the Left/Right arrows to choose the time period you want

Parental Control to be active: from 1 hour to 99 hours,

7. Select Set Password.

8. Press a Left/Right arrow and enter a 4-digit password when prompted.

(Verify the password by entering it a second time.)

9. Select Lock On/Off and use the Left/Right arrows to show On.

10. Press QUIT to remove the menu from view.

(_ aRental

Control

BlockVideo

SetHour.';

SetPasswol'd

LockOn/Off

] [c. a Blocked7

[Source Blocked 1

[,db" O1 Hours ]

[EnterCode: x x x x ]

[ On' !

Parental Control Menu

Remember your password! To re-

enter parental control while it's

on, yo,! must enter this number.

Other'Mse, you'll have to wait for

the specified time period to elapse.

Notes:

O Do not tr3,to deactivate the Parental Control by unplugging your TV. This only restarts Parental Control lock time.

[-I Parental Control cannot be turned On (Lock On/Off) until the Hours and Password have been set.

,USING AUTO DEMO

"Your new TV demonstrates on-screen menus that control the

TV's setup and operational features. Turn on Auto Demo to

show the on-screen menus one-by-one.

To Start Auio Demo i

1. Select Auto Demo using the Up/Down arrows.

2. Use the Left/Right arrows to set Auto Demo to On.

13. Press QUILTto remove the menu from view.

Note: Auto Demo will continue to

operate until you set it to Off in

the Setup Menu.

_ etupMenu

Auto Program

Add/bel/Surf

Ch. Labels

Clock Set

Timer Setup

Parental Ctl

Caption/Text .

Language ....

Auto Oemo ] [ On

Setup Menu with Aato Demo Highlighted

320s-o 3 -- 4

AUDIO MENU

MENU OPERATION

Audio Menu adjustments are optional. You don't have to adjust these features Io use your TV.

'_ Audio

? Menu

[Bass

Treble

Balance

Audio Mode

Surround t

SoundRite

] [,q i

-j

Menu Operation

1. Press MENU repeatedly to choose Audio Menu.

2. Press an IJp/Down arrow repeatedly to select zaa option.

3. Press a Left!Righl arrow repeatedly to adjust an option.

4. Press QUIT to remove a menu from view, or wait a few

seconds ancl the menu will disappear.

Menu Option

Bass

Treble

Balance

Audio Mode

Surround J_

SoundRite

Function

Adjusts the low frequency level.

Adjusts the high frequency level.

Adjusts the sound balance between the two speakers.

Selects Stereo, Mono (Monoaural), or 2nd Audio/SAP speaker operation. See infc rmation following this chart fi)r

more details.

Stereo: Directs the sound to the Left and Right speake[s as supplied by your TV, VCR, etc.

Mono: Directs the same sound to both Left and Right :speakers, even Lfthe program is in stereo.

2nd Audio/ Directs the sound for the Second Audio Program to both the Left and Right speakers. SAP

SAP: sound is always monaural. (SAP is not available if Video is ycur viewing source.)

Lets you hear front channel surround sound from the TV's speakers. (You'll hear surround sound only if the

program is in stereo and is encoded with surround sound.)

Maintains the TV's volume at a constant level (including commercials and audto _rom the auxiliary input source).

!4otes:

E] If you select stereo as the Audio Mode, the TV switches between Stereo and Mono (Monoaural) _;ound depending on the audio

signal received.

_3 If you select SAP as the Audio Mode, you'll hear SAP (usuall3. a second language) on stations broadcasting twc audio signals.

When the SAP broadcast ends, the TV switches between Stereo and Mono modes depending on the audio signal received. The

TV switches back to 2nd Audio/SAP when the SAP broadcast resumes.

3:os-o 4-- 1

m i

MENU OPERATION

VIDEO .MENU

Video Menu adjustments are optional. You don't have to adjust these features to use your TV.

_111 Video- Menu

[Contrast

Brightness

Color

Tint

Sharpness

Picture Pref

I< I _,]

Menu Operation

1. Press MENU repeatedly to, choose Video Me'au.

2. Press an Up/Down arrow repeatedly to select an option.

3. Press a Left/Right arrow repeatedly to adjust .an option.

4. Press QUIT to remove a meru from view, or wait a few

seconds and the menu will di mppear.

Menu Option

Contrast

Brightness

Color

Tint

Sharpness

Picture Pref.

(Preference',,

Function

Adjusts the picture's overall contrast and color level.

Adjusts the picture's brightness level of black areas.

Adjusts the picture's color intensity.

Adjusts flesh tones to more red or more green.

Adjusts object-edge definition for best picture quality.

Selects the video adjustments to be used.

PRESET restores the factory preset adjustments.

Note: Adjustments you make to the Video Menu settings are stored as Custom settings.

3:05-0 5_ 1

MENU OPERATION

] :_--_ Source

_.._ Menu

M_l Source

! IAntenna/Cable

1. Press MENU repeatedly to choose Source Menu.

2. Press an Up/Down arrow rep_:atedly to select an option.

3. Press a Left/Right arrow repeatedly to adjust an option•

4. Press QUIT to remove a mena from view, or wait a few

seconds and the menu will dis appear.

MenuOption Function

/ II

Main Source Select either Antenna/Cable or Video for the source that L;providing the picture. It can be the

I antenna or cable box connected to the Antenna/Cable jack or perhaps a VCR connected to the Aux Input

! A/V jacks. '

Note: You can change sources by pressing TV/VCR SOURCE on the remote.

:_205-o 6 -- 1

REMOTE (MBR344 7) -

GET• TO KNON YOUR " ' "

SIMPLE PRODUCT OPERATION " . "- - " -

VCR

Cable Box

2rid VCR (AUX)

'FV

ForTVOperation

1. Press TV product button.

2. Aim remote at TV.

3. Press POWER to turn on TV.

4. Press other buttons to operate

your TV's features.

For VCR Operation

1. Press VCR product button.

2. Aim remote at VCR.

3. Press POWER to turn on VCR.

4. Press other buttons to operate your

VCR'.,; features.

POWER On/Off

Product Buttons

For Cable Box Operation

i. Press CABLE product button.

2. Aim remote at cable box.

3. Press POWER to turn on your

cable box.

4. Press other buttons to operate

your cable box's features.

For2nd VCR Operation

1. Press AUX product button.

2. Aim remote at 2nd VCR.

3. Press POWER to tarn on VCR.

4. Press other buttons to operate your

VCR's features.

Your remote can operate up to seven different products. Turn to the following pages for programming instructions. You can pro-

gram the AUX button to operate a second TV or VCR, if desired.

! 3205-o 7_ 1

i :!_i_i_;._?GETTO;_KNOW:iYOUR_iREMOTE (MBR3447)

.'l

PROGRAMMING YOUR REMOTE • "-

If you're using Zenith products, the remote is already programmed for the most common codes: TV --:101, VCR = 201, CABLE =

353, and AUX = 401. For other brands, or if your remote falls to control your Zenith products, you'll have to progr_aa the remote.

1. Install the batteries if you have not already done so.

2. Press and hold O using a blunt object. Indicator light stays on to show you're in the programming

Release PRG after the indicator light turns on. mode.

:5.

Press then release the

button for the product

being programmed.

Enter 3-digit (_) (_) (_) rvs vc.s ci.,,:

. oductco e®®® }i i:

fromthechart ® ® ®

on the next page. @ @

Press then release @ to save the code.

Point remote at product and press @ to test the

product's operation. If it does not turn on, reprogram the

remote using a different code listed for your product.

Indicator light flashes to sho_ remote is ready to accept

a code.

Indicator li ht flashes for each digit you enter.

Indicator light on remote flashes and turns off to show your

code was accepted.

Product turns On.

If none of the codes listed for your product operates it, use

Auto Find as described on the following page.

7. Repeat the above steps to program the remote for another product.

3:z05-o , 7 _ 2

Page is loading ...

Zenith Sentry 2 Z25X22 Operating Manual & Warranty

Brand: Zenith

Model: Sentry 2 Z25X22

Category: LCD TVs

Type: Operating Manual & Warranty

This manual is also suitable for

Download PDF

report

Zenith Sentry 2 Z25X22 Operating Manual & Warranty

This manual is also suitable for

Zenith Sentry 2 Z25X22 Operating Manual & Warranty

Related papers

Other documents