Philips GC7051/30R1 User manual

Page is loading ...

2

3

54

6

910

12

13

11

8 7

1

3

CALC

CLEAN

1

12

2 4 5

6

15-30 min.

7 8 9

10

2 sec.

11

2 min.

12 13

14

15 16

IMPORTANT

- Perform Calc-Clean process regularly for great steam and prolonged life (Fig. 1).

- Recommended water to use: distilled or demineralised water (Fig. 2).

WICHTIG

- Führen Sie die Entkalkung für optimalen Dampf und eine lange Nutzungsdauer

durch (Abb. 1).

- Empfohlenes Wasser: destilliertes oder demineralisiertes Wasser (Abb. 2).

IMPORTANTE

- Realice el proceso Calc-Clean de forma regular para optimizar el vapor y prolongar la

vida útil del aparato (g. 1).

- Recomendación de agua para utilizar: agua destilada o desmineralizada (g. 2).

TÄRKEÄÄ

-

Käytä Calc-Clean-toimintoa säännöllisesti, sillä se takaa tasaisen höyryntuoton ja

laitteen pitkän käyttöiän

(Kuva 1).

- Suositeltu vesilaatu: tislattu tai pehmennetty vesi (Kuva 2).

IMPORTANT

- Eectuez régulièrement le traitement anticalcaire pour une vapeur de qualité et une

durée de vie prolongée (g. 1).

- Recommandation pour l’eau à utiliser : eau distillée ou déminéralisée (g. 2).

IMPORTANTE

- Eseguite regolarmente la procedura Calc-Clean per maggiore vapore e durata del

ferro (g. 1).

- Acqua da utilizzare: distillata o demineralizzata (g. 2)

BELANGRIJK

-

Voer de Calc-Clean-procedure regelmatig uit voor een hoge stoomproductie en een

langere levensduur

(g. 1).

- Aanbevolen water: gedistilleerd of gedemineraliseerd water (g. 2).

IMPORTANTE

-

Execute o processo Calc-Clean regularmente para um óptimo vapor e uma vida útil

prolongada (g. 1).

-

Água recomendada para utilização: água destilada ou desmineralizada (g. 2).

VIKTIGT

- Utför avkalkningsprocessen regelbundet för bättre ånga och förlängd livslängd på

produkten (Bild 1).

- Rekommenderat vatten att använda: destillerat eller demineraliserat vatten (Bild 2).

VIGTIGT

- Udfør afkalkningsprocessen jævnligt for at opnå god damp og forlænge apparatets

levetid (g. 1).

- Anbefalet vand, der skal bruges: destilleret eller demineraliseret vand (g. 2).

CALC

CLEAN

1

12

2

Page is loading ...

6 ENGLISH

Introduction

This iron has been approved by The Woolmark Company Pty Ltd for the ironing of

wool-only products, provided that the garments are ironed according to the

instructions on the garment label and those issued by the manufacturer of this iron.

R1401. In the United Kingdom, Eire, Hong Kong and India, the Woolmark trademark

is a certication trademark.

General description (Fig. 3)

1 Carry lock (specic types only)

2 Water tank lling funnel

3 Water tank

4 Iron platform

5 Water supply hose

6 Mains cord with plug

7 Calc-Clean button with Calc-Clean light

8 On/o button with power-on light

9 ECO button with light

10 Soleplate

11 Steam trigger

12 ’Iron ready’ light

13 Smart Calc-Clean container

OptimalTEMP Technology

The OptimalTEMP technology enables you to iron all types of ironable fabrics,

without adjusting the iron temperature.

- Fabrics with these symbols are ironable, for example linen, cotton, polyester, silk,

wool, viscose and rayon (Fig. 4).

- Fabrics with this symbol are not ironable. These fabrics include synthetic fabrics

such as Spandex or elastane, Spandex-mixed fabrics and polyolens (e.g.

polypropylene), but also prints on garments (Fig. 5).

Recommended water to use: distilled or demineralised water

Your appliance has been designed to be used with tap water. If you live in an area

with hard water, fast scale build-up may occur. It is therefore recommended to use

distilled or demineralised water to prolong the lifetime of your appliance.

Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling

agents, ironing aids, chemically descaled water or other chemicals, as they may

cause water spitting, brown staining or damage to your appliance.

Ironing

Please read the quick start guide on the packaging carefully to start using your

appliance.

Note: Keep the steam trigger pressed continuously when you move the iron over

the fabric while you iron.

7

IMPORTANT - Cleaning and maintenance

Smart Calc-Clean System

Your appliance has been designed with a Smart Calc-Clean system to ensure that

descaling and cleaning is done regularly. This helps to maintain a strong steam

performance and avoids dirt and stains coming out of the soleplate over time. To

ensure that the cleaning process is performed, the steam generator gives regular

reminders. Besides that, a second defence step to protect the steam generator from

scale is integrated: the steam function gets disabled if descaling is not done after

1 hour steam ironing once the reminder came up. After descaling is done, the steam

function will be restored. This takes place regardless of the type of water used.

Sound and light Calc-Clean reminder

- After 1 to 3 months of use, the light of the Calc-Clean button starts ashing and

the appliance starts beeping to indicate that you have to perform the Calc-Clean

process (Fig. 6).

- You can continue steam ironing for 1 hour while the Calc-Clean light ashes and

the appliance beeps. After 1 hour, the steam function is automatically disabled.

You have to perform the Calc-Clean process before you can continue steam

ironing. (Fig. 7)

Performing the Calc-Clean process with the Calc-Clean container

Do not leave the appliance unattended during the Calc-Clean process.

Always perform the Calc-Clean process with the Calc-Clean container. Do not

interrupt the process by lifting the iron up from the Calc-Clean container, as hot

water and steam will come out of the soleplate.

1 Fill up the water tank halfway (Fig. 8).

Note: Make sure that the appliance is plugged in and switched ON during the

Calc-Clean process.

2 Place the Calc-Clean container on the ironing board or any other even, stable

surface (Fig. 9).

3 Place the iron stably on the Calc-Clean container (Fig 10).

4 Press and hold the CALC-CLEAN button for 2 seconds until you hear short

beeps (Fig. 11)

Note: The Calc-Clean container has been designed to collect scale particles and

hot water during the Calc-Clean process. It is perfectly safe to rest the iron on this

container during the entire process.

5 During the Calc-Clean process, you hear short beeps and a pumping sound

(Fig.12)

6 Wait approximately 2 minutes for the appliance to complete process. When the

Calc-Clean process is completed, the iron stops beeping and the CALC-CLEAN

light stops ashing (Fig. 13).

7 Wipe the iron with a piece of cloth (Fig. 14). Put the iron back on the base

station.

Caution: The iron is hot.

8 As the Calc-Clean container becomes hot during the Calc-Clean process, wait

approx. 5 minutes before you touch it. Then carry the Calc-Clean container to

the sink, empty it and store it for future use (Fig 15).

ENGLISH

8

9 If necessary, you can repeat steps 1 to 8. Make sure that you empty the Calc-

Clean container before you start the Calc-Clean process.

Note: During the Calc-Clean process, clean water may come out of the soleplate

if no scale has accumulated inside the iron. This is normal.

For more information on how to carry out the Calc-Clean process, refer to the videos

in this link: http://www.philips.com/descaling-iron.

Energy saving

Eco mode

By using the ECO mode (reduced amount of steam), you can save energy without

compromising on the ironing result.

1 To activate the ECO mode, press the ECO button. The green ECO light goes

on. (Fig. 16)

2 To deactivate the ECO mode, press the ECO button again. The green light goes

o.

For the best results on tough fabrics you can use the TURBO mode.

1 Press and hold the on/o button for 2 seconds until the light turns white.

2 To deactivate the TURBO mode, press and hold the on/o button for 2 seconds

again until the light turns blue.

Safety auto-o (specic types only)

The safety auto-o function automatically switches o the appliance if it has not

been used for 5 minutes, to save energy.

Troubleshooting

This chapter summarises the most common problems you could encounter with the

appliance. If you

are unable to solve the problem with the information below, visit

www.philips.com/support for a list of frequently asked questions or contact the

Consumer Care Centre in your country.

Problem Possible cause Solution

The iron does

not produce any

steam.

There is not enough

water in the water tank.

Fill the water tank beyond the MIN

indication. Press and hold the

steam trigger until steam comes

out. It may take up to 30 seconds

until steam comes out.

You have not pressed

the steam trigger.

Press and hold the steam trigger

until steam comes out.

The steam function has

been disabled until you

have performed the

Calc-Clean process.

Perform the calc-clean process to

restore the steam function (see

chapter ‘IMPORTANT - Cleaning

and maintenance’).

The light of the

Calc-Clean

button ashes

and/or the

appliance beeps.

This is the Calc-Clean

reminder.

Perform the Calc-Clean process

within 1 hour after the Calc-Clean

reminder is given (see chapter

‘IMPORTANT - Cleaning and

maintenance’).

ENGLISH

9

Problem Possible cause Solution

The light of the

Calc-Clean

button ashes

and the

appliance beeps

every time I

press the steam

trigger. No steam

comes out of the

soleplate.

You have not done or

have not completed the

Calc-Clean process.

Perform the Calc-Clean process to

enable the steam function again

(see chapter ‘IMPORTANT -

Cleaning and maintenance’).

The appliance

has switched o.

The safety auto-o

function was activated.

This happens

automatically when the

steam generator has not

been used for more than

5 minutes.

Set the on/o switch to ‘o’

position and then to ‘on’ position.

The appliance

produces a loud

pumping sound.

The water tank is empty. Fill the water tank with water and

press the steam trigger until the

pumping sound becomes softer

and steam comes out of the

soleplate.

Water droplets

come out of the

soleplate.

After the Calc-Clean

process, remaining water

may drip out of the

soleplate.

Wipe the soleplate dry with a piece

of cloth. If the light in the Calc-

Clean button still ashes and the

appliance still beeps, perform the

Calc-Clean process (see chapter

‘IMPORTANT - Cleaning and

maintenance’).

The Calc-Clean process

has not been completed.

You have to perform the Calc-

Clean process again (see chapter

‘IMPORTANT - Cleaning and

maintenance’).

Dirty water and

impurities come

out of the

soleplate.

Impurities or chemicals

present in the water have

deposited in the steam

vents and/or soleplate.

Perform the Calc-Clean process

regularly (see chapter ‘IMPORTANT

- Cleaning and maintenance’).

Water ushes

out of the

soleplate.

You have accidentally

started the Calc-Clean

process (see chapter

‘IMPORTANT - Cleaning

and maintenance’).

Switch o the appliance. Then

switch it back on again. Let the iron

heat up until the ‘iron ready’ light

lights up steadily.

The Calc-Clean

process does not

start.

You have not pressed

the Calc-Clean button for

2 seconds until the

appliance started

beeping.

See chapter ‘IMPORTANT -

Cleaning and maintenance’.

ENGLISH

10

Problem Possible cause Solution

The iron leaves a

shine or an

imprint on the

garment.

The surface to be ironed

was uneven, for instance

because you were

ironing over a seam or a

fold in the garment.

Perfect Care is safe on all

garments. The shine or imprint is

not permanent and will disappear

when you wash the garment. Avoid

ironing over seams or folds or you

can place a cotton cloth over the

area to be ironed to avoid imprints.

The ironing

board cover

becomes wet or

water droplets

come out of the

soleplate.

Steam has condensed

on the ironing board

cover after a long ironing

session.

Replace the ironing board cover if

the foam material has worn out.

You can also add an extra layer of

felt material under the ironing

board cover to prevent

condensation on the ironing board.

You may have an ironing

board that is not

designed to cope with

the high steam rate of

the steam generator.

Put an extra layer of felt material

under the ironing board cover to

prevent condensation on the

ironing board.

Steam continues

to come out after

I release the

steam trigger.

Steam is generated in

the soleplate. When you

release the steam trigger,

remaining water is

transformed into steam.

This is normal.

Release the steam trigger 2 to 3

seconds before you place the iron

back on the iron platform or ironing

board.

There is a strong

gush of steam

when I release

the steam trigger

after placing the

iron on the iron

platform.

When the iron is tilted

upwards, remaining

water is collected and

converted into strong

steam. This is normal.

Release the steam trigger 2 to 3

seconds before you place the iron

back on the iron platform or ironing

board.

Steam is weak. You do not press the

steam trigger

continuously.

Keep the steam trigger pressed

continuously when you move the

iron over the fabric.

You use the ECO mode. For more steam, switch o the ECO

mode by pressing the ECO button.

The green ECO light goes o.

Steam does not

come out

immediately

when I press the

steam trigger.

Water is converted into

steam in the soleplate.

When you press the

steam trigger, it will take 1

to 2 seconds until steam

is generated and

released. This is normal.

Keep the steam trigger pressed

continuously when you move the

iron over the fabric.

ENGLISH

Page is loading ...

Philips GC7051/30R1 User manual

Philips GC7051/30R1 User manual

in other languages

Related papers

Other documents