INNOSILICON A4+ LTCMaster User manual

Type
User manual

This manual is also suitable for

A6 LTCMaster
USER MANUAL
INNOSILICON CONFIDENTIAL
Table of Contents
1. OVERVIEW 1
2. MINER ASSEMBLE 2
2.1 Check the miner before power on 2
2.2 Connect the PSU 3
2.3 Connect the Ethernet Cable 3
3. ENTER THE MINER CONSOLE 3
4. CONFIG THE MINER 6
5. APPENDIX 10
5.1 Modify the login password 10
5.2 Upgrade the firmware 10
INNOSILICON CONFIDENTIAL
INNOSILICON A6 LTCMaster
High Efficient LTCMaster
INNOSILICON CONFIDENTIAL
1
1. OVERVIEW
INNOSILICON CONFIDENTIAL
A6 LTCMaster
Part Number A6 LTCMaster
Hash Rate 1.23Gh/s (+-8%)
Power 1500W+/-8%
Size (L×W×H) (L)350mm*(W)250mm*(H)155mm (dual tube)
Net Weight 8.46KG (without PSU)
Operating Temperature 0-40
Required rated PSU 1800W or above, 17 * PCI-E 6Pin
Network Connection Ethernet
INNOSILICON CONFIDENTIAL
2
2. CABLE CONNECTION
2.1 CHECK THE MINER BEFORE POWER ON
· Check the warranty sticker is well or not, especially the hashboards PSU port side. If the warranty sticker
is damaged when you received the miner, please contact our After-sales.
· Before you power on the miner, shake the miner softly, if you can hear the sound of metal banging on
metal, please contact our After-sales.
· Check if the fan work well, if you find the fans broken please contact our After-sales.
· Check the cable connection, if it is different from below picture, please connect the cables as below.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
3
2.2 CONNECT THE PSU
Every hash board needs to be inserted with 2 PSU cables, controller only needs 1 PSU cable according to
the following image .
2.3 CONNECT THE ETHERNET CABLE
Insert one end of the Ethernet cable into the router and the other end into the slot shown in the following
image, you should plug in the miner one by one, only when you have accomplished IP Setting of the
previous one you can plug in another miner .
IP SET button: Press it more than 5 seconds to recover the IP to 192.168.1.254.
RESET button: Your miner will restart if you press it. It wont recover your settings to the default.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
4
3. ENTER THE MINER CONSOLE
By default, the miner uses Static IP to access the control webpage of the miner.
Input 192.168.1.254 into the browser, then click ‘Enter’ to enter the miners control webpage (Chrome is
the suggested browser).
Cant access the miner console?
Maybe it is because miner IP and the router IP have a different network segment, two ways to solve it:
· Modify the router IP to 192.168.1.1,then try again.
· Don’t want to change the network segment of the router? Do it as below:
Connect the miner and computer with a network cable. Open the windows system control panel, go to
Network and Internet — Network and share center – change the adapter settings, the mouse cursor to
the “Local Area Connection” click the right mouse button to view properties.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
5
· Press the OK button twice to confirm the changes.Then modify the IP address of the miner (Do it as the
follow step 4.4) to guarantee the miner and the router have the same network segment.Then connect
the miner with the router,connect the PC with the router and select the “Obtain the IP address
automatically.Now you can enter the IP through the browser into the control interface
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
6
· Press the OK button twice to confirm the changes.Then modify the IP address of the miner (Do it as the
follow step g) to guarantee the miner and the router have the same network segment.Then connect
the miner with the router,connect the PC with the router and select the “Obtain the IP address
automatically.Now you can enter the IP through the browser into the control interface
4. CONFIG THE MINER
4.1 Enter ‘Miner Configuration’ page, select ‘General Settings’. Click the lower right corner to
enter log in page.
4.2 Enter the default password“12345678”, then click lower right corner to enter
configuration page.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
7
Password is wrong/error?—Please contact our after-sales people.
4.3 Enter the mining pool’s URL, Worker, password according to the following image, then click
.The miner will start mining, and the page will return to the ‘Miner Configuration’ page. It will show
the users modified setting.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
8
4.4 To avoid IP conflict when using 2 or more miners at the same time, the IP address needs to be
changed. Enter the network interface shown in the following image, and modify the IP address to you
need, then click the “Save” to save it.
NoteIf you change the miner IP address to another network segment, after you save it there will be
3 circles keep spinning,that is ok.
> IP address: If the router address is 192.168.0.1you can change the miners IP address to
192.168.0.## can be any number between 10-253 but every miners # must be unique.
> Subnet mask: Keep it consistent with your computer.
> Gateway: Same with the router address.
> DNS: It is recommended to modify the DNS to the local network operator near the location of the
miner. For example, the mining machine uses telecommunication broadband in Beijing, China. Search
in Baidu or Google search engine "Beijing Telecom DNS" to get the DNS: 219.141.136.10. Then use
this DNS for your miner.
When the above information is input, click the lower right corner to save.
4.5 Enter ‘Miner Status’ page to check the status on the mining pool configuration and performance of the
miner.
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
9
HW: means error in calculating
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
10
5. APPENDIX
5.1 MODIFY THE LOGIN PASSWORD
Select the “Administration” interface at System, then you can modify your password. Then click
to save your new password.
Download the firmware from Support Center: http://www.innosilicon.com/html/downA4/
Then select the “Upgrade” interface at System option, click to choose the firmware you want to upgrade,
click the “update” to start the upgrade. The upgrade is success when you see the progress bar reach to
100%.
5.2 UPGRADE THE FIRMWARE
INNOSILICON CONFIDENTIAL
A6 LTCMaster
INNOSILICON CONFIDENTIAL
Note: As the factory reset will not reset the
password to the default password, you must
take care your new password. If you forget
the password, it can only recovered through
our paid support. (Very IMPORTANT!!!)
Note: Don’t power off the miner when is is
upgrading. When the progress bar reach to
100%, upgrade done and it will reboot by
itself. Then use “Ctrl+F5” to refresh.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

INNOSILICON A4+ LTCMaster User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI