Tools Required:
5
⁄16 in. Hex nut driver
3
⁄8 in. Electric drill
1
⁄2 in. Open end wrench
Crossover
Blade Axle.
Do not attach
Control Shaft
here!)
1
2
Before Installing Damper in the Duct
1. If damper has more than one blade, determine which
blade axle will be driven by the extended control
shaft. Always attach extended control shaft to a
blade axle which is directly connected to the main
linkage tiebar. DO NOT attach extended control shaft
to a crossover blade axle.
2. Cut hole approximately 1 in. (25mm) diameter in
duct where damper drive blade axle will be located.
Hole must provide clearance for enlarged portion of
extended control shaft.
After Damper is Installed in Duct
1. Push extended control shaft through hole in duct
and onto drive blade axle. Retainer clip should
“click” into groove on drive blade axle and hold shaft
into place.
Standard control shaft location is the third blade
from the bottom on dampers with three or more
blades. Control shaft location is the first blade from
the bottom on dampers with one or two blades.
Part Number 846032
316SS Extension Pin with Clip
No. Qty Description Part Number
1 1 6 in. Control Shaft 463921
2 1 Retaining Clip 454204
®
Installation, Operation and Maintenance Manual
Note: For dampers installed in ducts
Extended control shaft is installed from outside of duct after damper is installed. Install as shown below.
1
SS Extension Pin Kit
Document #474711
Field Installation Instructions for 316SS
Extension Pin, Extension Pin Kit & Manual
Quadrant Operators on Control Dampers
Before Installing Damper in the Duct
1. If damper has more than one blade, determine which
blade axle will be driven by the extended control
shaft. Always attach extended control shaft to a blade
axle which is directly connected to the main linkage
tiebar. DO NOT attach extended control shaft to a
crossover blade axle.
2. Cut hole approximately 1 in. (25mm) diameter in
duct where damper drive blade axle will be located.
Hole must provide clearance for enlarged portion of
extended control shaft.
After Damper is Installed in Duct
1. Push extended control shaft through hole in duct and
onto drive blade axle. Retainer clip should “click”
into the groove on the drive blade axle and hold shaft
into place. Standard control shaft location is the third
blade from the bottom on dampers with three or more
blades. Control shaft locations the first blade from the
bottom on dampers with one or two blades.
2. Install the stand off bracket with bearing over the
extended control shaft and screw bracket to the
duct. Make sure screws (provided by others) do not
interfere with damper linkage or blade movement.
Caution: Stand off bracket with bearing is needed to
support the extended control shaft. If not installed as
directed, the extended control shaft may not operate the
damper correctly.
Part Number 829038
316SS 1/2 in. Extension Pin Kit
No. Qty Description Part Number
- 4 Screws by others
1 1 Stand off bracket with ball bearing 687784
2 1 Extended Control Shaft (6 in.) 463921
3 1 Retaining Clip 454204
Crossover
Blade Axle
(Do not
attach
Control
Shaft here!)
Part Number 829039
316SS 1/2 in. Extension Pin Kit with Manual Quadrant
No. Qty Description Part Number
1 1 Standoff Bracket 687784
2 1 Extended Control Shaft (6 in.) 463921
3 1 Retaining Clip 454204
4 1 Manual Quadrant (
1
⁄2 in.) 464699
5 2 0.125 in. Rivet 416308
6 1 Label - Open/Close 452690
2
3
1
6
4
5
Part Number 879734
316SS 1/2 in. Extension Pin Kit
No. Qty Description Part Number
- 4 Screws by others
1 1 Stand off bracket with ball bearing 687784
2 1 Extended Control Shaft (12 in.) 879738
3 1 Retaining Clip 454204
2
SS Extension Pin Kit
Part Number 872390
316SS 1 in. Manual Quadrant Kit
No. Qty Description Part Number
1 1 Manual Quadrant Bracket 687407
2 1 1 in. Quadrant Lever Arm 827734
3 1
3
⁄8-16 x 1
1
⁄4 316SS Bolt 415780
4 1
1
⁄2 in. flat washer SS 415401
5 1
3
⁄8 -16 x 2
1
⁄2 316SS Bolt 415944
6 1
3
⁄8 in. 316SS Locking Washer
415810
7 1
3
⁄8-16 Hex Nut 316SS 415799
8 1 Label, Open/Close 452690
9 1
3
⁄8 -16 wing nut 316SS 416132
10 1 Standoff Bracket 687405
11 8
1
⁄4-20 x
1
⁄2 bolt 316SS 415868
12 8
1
⁄4 in. Locking Washer 316SS 415837
13 8 1/4-20 Nut 316SS 415835
Non-Jackshafted Dampers
Control damper should be mounted in the duct and the
shaft extension mounted onto the correct blade of the
damper before continuing with these instructions.
After Extended shaft is Installed
1. Assemble manual quadrant to extension bracket
assembly (screws provided).
2. With damper either fully open or closed, lock manual
quadrant to extended control shaft so manual
quadrant can move damper between open and
closed.
Note: Tighten down bolt on manual quadrant to 250
in. lbs. of torque.
Apply “OPEN” and “CLOSED” labels if damper
movement is opposite to that engraved in the
manual quadrant.
3. Set damper to desired position and tighten wing nut
on manual quadrant to hold damper in place.
9
4
5
2
1
3
7
8
6
JACKSHAFT AND BRACKET
SHOWN FOR REFERENCE
10
13
12
11
11
Jackshafted Damper
Jackshafted Dampers
1. The jackshaft is, either, 1/2 in. or 1 in. diameter
depending upon the size of the damper. The manual
quadrant kit for the 1/2 in. diameter jackshaft is part
number 811518 and the manual quadrant kit for 1 in.
diameter jackshaft is part number 813938.
2. With the damper either fully open or closed, lock
manual quadrant to jackshaft so manual quadrant
can move damper between open and closed.
Note: Tighten down the bolt on the manual quadrant
to 250 in. lbs. of torque.
Apply “OPEN” and “CLOSED” labels if damper
movement is opposite to that engraved in the manual
quadrant.
3. Set the damper to desired position and tighten wing
nut on manual quadrant to hold damper in place.
3
SS Extension Pin Kit
4
474711 • SS Ext Pin Kit IOM, Rev. 3, April 2017 Copyright 2017 © Greenheck Fan Corporation
As a result of our commitment to continuous improvement, Greenheck reserves the right to change specifications
without notice.
Specific Greenheck product warranties are located on greenheck.com within the product area tabs and in the
Library under Warranties.
Phone: (715) 359-6171 • Fax: (715) 355-2399 • E-mail: [email protected] • Website: www.greenheck.com
Our Commitment
/