2. AGT INDUSTRIAL
  3. AGT-4IN1BCT
AGT-4IN1BCT

AGT INDUSTRIAL AGT-4IN1BCT Owner's manual

  • Hello! I am a chat assistant and I've reviewed the product manual for the AGT INDUSTRIAL 4 IN 1 Bucket, model AGT-4IN1BCT. This manual provides key details on safety, installation, operation, and maintenance of this device. It covers everything from wearing proper safety gear to ensuring the equipment is properly installed before use. I am ready to answer your specific questions about this product based on the document.
  • What should an operator do before operating the machine?
    What safety measures should an operator be aware of?
    What type of protective equipment should be used?
PRODUCT MANUAL
AGT INDUSTRIAL
4 IN 1 Bucket
Ver.1.1.3
Model:AGT-4IN1BCT
P2
TABLE OF CONTENTS 2/9
TO THE OWNERS 3/9
TABLE OF CONTENTS
SAFETY PRECAUTIONS 4/9
ROTOTILLER ASSEMBLES 7/9
PERATION INSTRUCTIONS 8/9
NOTES 9/9
P3
TO THE OWNERS
GENERAL COMMENTS
Congratulations for having this 4 IN 1 Bucket! Your 4 IN 1 Bucket was carefully
designed and manufactured to give you years of dependable service. Your 4
IN 1 Bucket will require some minor maintenance to keep it in top working
condition.
Please observe all safety precautions and maintenance procedures as
described in this manual.
BEFORE OPERATION
Thoroughly read and understand the instructions given in this manual before
operation. Refer to the "Safety Label" section, read all instructions noted on
them.
Do not allow anyone to operate his equipment who has not fully read and
comprehended this manual and who has not been properly trained in the
safe operation of the equipment.
SERVICE
Please remember to use only manufacturer replacement parts. Substitute
parts may not meet the standards required for safe, dependable operation.
P4
SAFETY PRECAUTIONS
BEFORE OPERATION
1. The operator must read the operation manual carefully before
installation, operation or maintenance. Improper operation will cause the
machine damage or the operator death.
2. Read all the safe signs and safe declarations. Follow all the professional
safe terms, local laws or the professional directions.
3. Familiar with the 4 IN 1 Bucket about functions, specs and operation.
Replace the to-be-damaged parts in time. Make sure all the hydraulic
installations and couplings connect firmly, and all the safe signs stick on the
suitable positions clearly.
1. Operator should be familiar with all functions of the unit.
2. Make sure all guards and shields are in place and secured before operating
implement.
3. Keep all persons away from equipment and work area.
4. Dismounting from a moving unit can cause serious injury or death.
5. Keep hands, feet, and clothing away from power-driven parts.
6. Detach and store implement in an area where children normally do not play.
Secure implement by using blocks and supports.
IMPORTANT
Always wear proper safety glasses, goggles, or a face shield when
driving pins in or out, or when any operation causes dust, flying
debris, or any other hazardous material.
P5
SAFETY PRECAUTIONS
Operator Safety
►Wear protective clothing and equipment appropriate for the job. Clothing
should be snug fitting without fringes and pull strings to avoid entanglement
with moving parts.
►Prolonged exposure to loud noise can cause hearing impairment or
hearing loss. Wear suitable hearing protection such as earmuffs or earplugs.
►Operating equipment safely requires the operators all attention, Avoid
wearing radio headphones while operating machinery.
Tool Safety
►Inspect entire machine before each use. Replace damaged or worn parts.
►Check for fuel leaks and make sure all fasteners are in place and securely
fastened.
P6
SAFETY PRECAUTIONS
Wear Protective Equipment
►Escaping fluid under pressure can penetrate the skin causing serious injury.
►Avoid the hazard by relieving pressure before disconnecting hydraulic lines
or performing work on the system.
►Make sure all hydraulic fluid connections are tight and all hydraulic hoses
and lines are in good condition before applying pressure to the system.
►Use a piece of paper or cardboard, NOT BODY PARTS to check for
suspected leaks.
►Wear protective gloves and safety glasses or goggles when working with
hydraulic systems.
►DO NOT DELAY. If an accident occurs, see a doctor familiar with this type of
injury immediately. Any fluid injected into the skin or eyes must be treated
within a few hours or gangrene may result.
Transportation and Storing
►Store machine and fuel where fuel vapors cannot reach sour combustion
like, water heaters, electric motors, switches, furnaces, etc.
►Always secure the machine with tie downs or similar restraints when
transporting.
►The machine be stored in a manner that prevents it from falling, rolling or
tipping.
P7
BUCKET ASSEMBLES
P8
S/N PART NO. PART DESCRIPTION QTYS NOTE
1 Bucket Weldment 1
2 Frame Weldment 1
3 Pin Bearing Weldment 1 2
4 Pin Bearing Weldment 2 2
5 Pin Bearing Weldment 3 2
6 Bucket Plate 1
7 Bucket Bracket 1
8 Nozzle 40*50*30 4
9 Hex Bolt M12*40 16
10 Ring φ12 16
11 Lock Washer φ12（Galvanized）16
12 Common Nut M12 16
13 Lock Washer φ10（Galvanized）6
14 Bolt M10*25（Galvanized）6
15 Ringφ10 6
16 Grease Fittiing M10*1 6
17 4IN1 Bucket Cylinder 2
P9P7
P8
OPERATION INSTRUCTIONS
Never run the skid steer engine in a closed building without adequate
ventilation, as the exhaust fumes are very dangerous.
1. Always make sure all 4N1 bucket components are properly installed and securely fastened
BEFORE operation.
2. Always start the engine from the operator's seat with all the transmission lever(s) and 4N1
bucket drive lever (if applicable) in neutral.
3. DO NOT bypass the safety system by shorting across the terminals of the starter motor to
start the engine. This may cause the skid steer to move suddenly.
4. If the safety start system does not work, consult your dealer immediately.
5. DO NOT use the 4N1 bucket near the edge of drop-offs or banks.
6. DO NOT use the 4N1 bucket on steep slopes as overturn may result.
7. Operate up and down (not across) intermediate slopes. Avoid sudden starts and stops.
8. Drive skid steer backwards up steeper slopes.
9. Slow down before you change directions on any slope.
10. Use wheel weights on your skid steer to increase stability on slopes.
11. Make sure the skid steer is counterweighted as recommended by your dealer. Weights
provide the necessary balance to improve stability, traction and steering.
12. Be especially observant of the operating area and terrain. Watch for holes, rocks, or other
hidden hazards. ALWAYS inspect the area prior to using the 4N1 bucket.
13. Keep the parking brake on at all times during transportation.
14. Always drive at a safe speed relative to local conditions and ensure that your speed is low
enough for an emergency stop to be safe and secure.
15. Always keep the skid steer in gear to provide engine braking when going downhill. Do not
coast.
16. Park the skid steer/4N1 bucket on level ground, place the transmission in neutral, set the
parking brake, disengage the Aux hydraulics, lower the equipment to the ground, place all
levers including auxiliary control levers in neutral, shut off the engine and remove the ignition
key BEFORE leaving the skid steer.
/