VISUAL COMFORT ARN 5173 User manual

ARN 5173
VISUAL COMFORT
Brand
VISUAL COMFORT
Model
ARN 5173
Type
User manual
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. It is recommended to install a 1/4 IPS threaded pipe, secured to a
structural member of the building (not included). Then install threaded
nipple (B) into receiver and tighten with wrench.
NOTE: Item must be supported independent of the junction box due
to hanging weight.
3. Remove lock collar (D) from chain (L) and secure to threaded receiver
attached to structural member by tightening locknut.
4. Install canopy (E) to collar loop (D) and secure with collar ring (F).
5. Determine desired overall length, and amount of chain (L) needed.
Shorten chain using chain pliers. (Keep extra chain)
6. Attach chain (L) to collar loop (D) and fixture loop (H) using quick
links (G). Secure quick links (G).
7. Thread fixture wire, ground wire and safety cable through chain (L).
NOTE: When you reach the collar loop (D), ensure there is no tension
on the wires. Cut excess wires, being sure to leave about 12” to reach
the junction box.
8. Separate two sides of molded wire, and strip insulation on each 5/8".
9. Loosen collar ring (F) and let canopy (E) slip down chain (L) carefully.
Liscia Chandelier
Item # ARN 5173
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver Slotted Screwdriver Chain Pliers
Slip Joint Pliers Wire Strippers Measuring Tape
Wire Cutters
NOTICE:
US
M
L
I
D
S
E
T
Bulbs not included
M 46PCS N 218PCS PLIERS
A
B
D
G
L
G
E
F
H
M
M
N
1/4 IPS Pipe-(Not provided)
Diagram 1
Diagram 2
1.875"
3"
Liscia Chandelier
Item # ARN 5173
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
10. Twist all fixture wires together. Slip through center hole of collar
loop (D).
NOTE: Untwist wires and separate to prepare for connection.
11. Loosen cable lock and install to end of safety cable. Run safety cable
through junction box and around structural member of building.
Insert cable through cable lock and tighten the ends with a
screwdriver to secure. See diagram 1)
12. Connect fixture ground wire (bare copper) to the supply ground wire
(usually green or bare copper) using wire nut (A).
NOTE: It is imperative that the fixture is grounded.
13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually
white) using wire nut (A).
14. Connect fixture hot wire (smooth with markings) to the supply hot
wire (usually black) using wire nut (A).
CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the
junction box.
16. Install canopy (E) to collar loop (D) and secure with collar ring (F).
17. Install light bulbs into the sockets.
18. Hang crystals (M) & (N) starting from bottom (layer 1) and working
your way to the top (layer 6) as shown in figures L1-L6 and
diagram 2.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do
not use abrasive or chemical agents.
NOTICE:
US
M
L
I
D
S
E
T
Bulbs not included
M 46PCS N 218PCS PLIERS
A
B
D
G
L
G
E
F
H
M
M
N
1/4 IPS Pipe-(Not provided)
Diagram 1
Diagram 2
1.875"
3"
Liscia Chandelier
Item # ARN 5173
ASSEMBLY INSTRUCTIONS
This light fixture should be installed in accordance with all applicable,
local installation codes, and by a person familiar with the construction
and operation of it, as well as the hazards involved. Inspect item and
contents carefully. If any damage or defect is found, do not install.
Retain all packaging material until installation is complete and approved.
NOTICE:
Layer 6
Layer 5
Layer 4
Layer 3
Layer 2
Layer 1
Layer 4
Layer 3
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
M
MMMMMMMM
M
M
M
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NNNNN
N
N
N
N
N
N
N
N
N
N
N
N
N
NNN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NNNNNNNN
N
N
N
N
N
N
N
N
N
N
N
NNN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NNNNN
N
N
N
N
N
N
N
N
N
NNNN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NNNN
N
Layer 1 Layer 2
US
M
L
I
D
S
E
T
Layer 6Layer 5
M
M
M
M
M
MM
M
M
M
M
M
M
M
M
M
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NNNN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
  • Page 1 1
  • Page 2 2
  • Page 3 3

VISUAL COMFORT ARN 5173 User manual

ARN 5173
VISUAL COMFORT
Brand
VISUAL COMFORT
Model
ARN 5173
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents