Columbia Lighting CRN2 Remote Installation guide

Brand
Columbia Lighting
Model
CRN2 Remote
Type
Installation guide
CRN2 Remote Instruction Manual
CRN2
WET LOCATION HIGH BAY
currentlighting.com/columbialighting
© 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 1 of 2
Rev 07/20/22
COL_CRN2_remote_inst_R01
NOTE: Components shown in images are
representative only and may vary based
on the conguration ordered.
Model: HD02R
ON/OFF
Press the “On/o” button, the light keeps permanently on or o. Press “Auto
Mode”, “Reset” or “Scene mode” buttons to quit from this mode.
Scene
Mode
(locked)
Auto Mode
Press “Auto Mode” button, the sensor starts to work and all settings remain the
same before the light gets switched on/o.
Reset
Press “Reset” button, products with DIP switch will be controlled by DIP switches;
otherwise all the setting will be just initial, that is 100% detection range, hold time
5S, no stand-by time and daylight threshold disabled.
Attention
1. Light turns on when sensor is wired correctly.
2. When using ON/OFF button, the rest of the setting buttons don't work.
3. Press "Auto Mode", "Scene mode" or "Reset" button before setting
detection range, hold time, daylight threshold, standby dimming level and
standby period, sensor flickers after receiving signals.
4. Every change will be automatically saved.
REMOTE FOR DIMMABLE SENSORS
Detection area
Press to define detection area: 100%/75%/50%/25%
Scene
Mode
Detection
Area
Hold
Time
Daylight
Threshold
Stand-by
Period
Stand-by
Dimming
Level
SC1 100% 30s 2 lux 1 min 10%
SC2 100% 5 min 10 lux 10 min 10%
SC3 100% 10 min 50 lux 30 min 10%
SC4 100% 30 min Disable + ∞ 10%
Hold time
Press to define hold time: 5s/30s/1min/3min /5min/10min/20min/30min
Stand-by dimming level
Press to define stand-by dimming level: 10%/20%/30%/50%
Stand-by period
Press to define stand-by period: 0s/10s/30s/1min/5min/10min/30min/+∞.
Note: “0s” means no standby period; “+∞” means unlimited standby period.
Daylight threshold
Press to define daylight level: 2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/Disable
Note: Disable means light will be turned on once sensor detects movement,
regardless of the ambient lux.
2s Test
The button “Test (2s)” is for testing purpose after commissioning. Pressing this
button causes the sensor to go into test mode (hold time is only 2s).
CRN2
WET LOCATION HIGH BAY
CRN2 Remote Instruction Manual
currentlighting.com/columbialighting
© 2022 HLI Solutions, Inc. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 2 of 2
Rev 07/20/22
COL_CRN2_remote_inst_R01
sensor sensor
15m7.5° 7.5°
4m
Other Information
1. The suggested distance between sensors is 4M (13ft).
2. If wall-mounting, the suggested height is 1–1.8M (3.2–5.9ft).
3. The distance between remote to the sensors is normally 15M (49ft), but could be aected by dierent environment or with dierent drivers.
  • Page 1 1
  • Page 2 2

Columbia Lighting CRN2 Remote Installation guide

Brand
Columbia Lighting
Model
CRN2 Remote
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents