2. ATEN
  3. VM6809H
VM6809H

ATEN VM6809H User manual

  • Hello! I am an AI chatbot trained to assist you with the ATEN VM6809H User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
4K
4K 30 Hz 8x9 HDMI Matrix Switcher with Apps & WEB GUI
Version: V22.06
USER MANUAL
2
Safety Reminder
To protect the device and operating personnel from electrostatic discharge, you need to
check and ensure that the device is grounding well before the device is powered on. Please
observe the following when you install, use, maintain this equipment.
Make sure the device ground connection.
Important Safety Instructions
1
Warnings of FCC
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and decoder.
-- Connect the equipment into an outlet on a circuit different from that to
which the decoder is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
2
Contents
Warnings of FCC..............................................................................................................................1
1. Product Introduction.............................................................................................................. 3
2. Features......................................................................................................................................... 3
3. Specification................................................................................................................................3
4. Connection Diagram............................................................................................................... 4
5. Packing........................................................................................................................................... 4
6. Panel description......................................................................................................................4
7. Matrix Switcher control........................................................................................................ 6
Remote Control........................................................................................................................... 6
APP control....................................................................................................................................6
WEB GUI browser Control........................................................................................................8
The 3rd Party Control command.......................................................................................... 8
8. Common Problem Shooting............................................................................................. 10
9. After-Sales................................................................................................................................. 11
3
1. Product Introduction
This is a new WolfPack 4K 30 Hz 8x9 HDMI Matrix Switcher with Apps & WEB
GUI with 8 HDMI inputs and 9 HDMI outputs, the resolution can up to 4K30Hz
and all ports are HDCP compliant. With the friendly user control methods by
IR remote control, 2-Press push buttons with background blue light, WEB GUI,
APP and RS232/UDP commands, this matrix switcher can work with the
Blu-Ray Players, Set-Top boxes, Home Theater, and game consoles etc HDMI
input sources to route to the HDMI displays, it has been widely used in
different audio visual applications.
2. Features
➢ 8 HDMI inputs and 9 HDMI outputs
➢ Support 1 audio(3.5mm) de-ebmedded
➢ Supports HDMI1.4, HDCP1.4
➢ The resolution can up to 4K@30Hz
➢ Deep Color support 48/36/30/24-bit
➢ Supports LPCM 7.1CH, Dolby TrueHD, Dolby Digital and DTS-HD Master
Audio
➢ Supports IR remote control(IR remote control codes are available)
➢ Supports smart EDID management, including 8-output EDID, 15 internal
EDID.
➢ Supports RS-232 and TCP/IP Control(WEB GUI, APP and IR remote)
➢Supports 2-press push buttons control with blue lights
➢Supports to rename the inputs and outputs, scenes
3. Specification
Name
4K 30 Hz 8x9 HDMI Matrix Switcher with Apps & WEB GUI
Resolutions
480i, 576i, 480p, 576p, 720p, 1080i,
Input ports
8 * HDMI, 1* RS-232(control), 1 * RJ-45(control)
Output ports
9 * HDMI, 1* RS-232(control)
ESD Protection
±8kV (Air-gap discharge), ±4kV (Air-gap discharge)
Controlling
IR remote control, front buttons control, RS232, UDP
4
Power
DC:12V 2A
Dimension(mm)
440*150*44(mm)
Weight
2kg
4. Connection Diagram
5. Packing
6. Panel description
Front panel
No.
Name
Qty
Unit
1
HDMI Matrix Switcher
1
Pcs.
2
DC 12V2A power adapter
1
Pcs
3
Remote Control
1
Pcs
4
Rack ear
2
Pcs
5
1LCD screen: for the switching, EDID, IP etc information display.
2INPUT: 8 HDMI input buttons
3OUTPUT: 9 HDMI output buttons
4CONTROL:
UP: for upward controlling, or when press input and press UP to all
outputs
EDID: Press it to enter EDID set mode.
SAVE: Press to save the switching status.
Down:for upward controlling
ENTER: Press to confirm to save the setting.
RECALL: Press it to recall the presets/scenes.
5IR: IR receiver for the IR remote control
Back panel
1For the ground wiring
2INPUT: 8 female HDMI Input ports
33.5mm audio output from output 1
4OUTPUT: 9 female HDMI output ports
5Control other devices: from the WEB GUI setup to fill out the commands
6RS232 IN: Female RS232 port for the R232 control
7RS232 OUT: Famle RS232 port for the RS232 control
6
8LAN: for the IP/TCP control, the default IP address is 192.168.1.80
9DC12V: power supply port
10 ON/OFF: power off/on switch
7. Matrix Switcher control
This Matrix switcher can support IR remote, APP, RS232/TCP/IP software, WEB
GUI browser or the front push-buttons control.
Remote Control
Users also can control this matrix switcher with the remote control. Note the
below buttons are not functional on this product: Standby, Auto, 4K, 1080p,720P,
1366
Channel switching:
Press the input from number “1~8”, then press the output from number“1~9”,
can press the outputs continually.
Eg. Switch input 1 to output 1, 2, 3:
INPUT 1 OUTPUT 1, 2, 3
Switch any inputs to all outputs:
Press input from number “1~8”, then press “UP” or “ALL” button.
SAVE: for the preset cave. “SAVE” select from the INPUT buttons(1~8)
OUTPUT buttons(1~9)
“ENTER”, will hear a beep sound.
RECALL: for the saved presets recalling. “RECALL” select from the INPUT
buttons(1~8) OUTPUT buttons(1~9) “ENTER”, will hear a beep sound.
MENU: for back to homepage/status
CLEAR: to disconnect the selected input to the outputs
ENTER: to confirm the switching, scenes save&recall
APP control
Users can download the APP from the Google play or Apple store by searching
keywords “MCS”, then need to make sure the Matrix switcher is connected to the
WIFI router and the mobile devices is connected to the same WIFI. The default IP
address of the matrix switcher is 192.168.1.80.
Open the APP and Enter the IP address of the matrix switcher:
7
Click Enter and login with the user name and password, the default User name is
admin, password is admin.
Click Submit to login after typing the correct user name and password, and it will
turn to the home interface for the sources Switch, Scene Recall/Save:
Users can change input, output and Scenes names here, up to 8 characters.
8
Users also can do the settings for the “Setup” tap
Users can change the default user name and password from the “Account” Tap:
WEB GUI browser Control
Users also can use the WEB browser to control the matrix switcher, users can
have the matrix switcher connected with the PC with the LAN cable directly or
have the matrix switcher connected the same network switch. The default IP
address of the matrix switcher is 192.168.1.80.
9
After opening the browser, users can type the matrix switcher IP address and
press enter:
The default user name is admin and the password is admin.
After login, it will turn to “Home” interface, users can do the sources switching,
scenes recall, save and the other devices control here.
Caption tab is from users to change then input, output, scene names, also can
setup the control other devices commands here.
EDID setting tab for users to select or setup the EDID for the specific inputs
Setup interface for users to do the IP address, COM baud rate and buzzer
settings:
Account interface for users to change the login user name and password:
The 3rd Party Control command
IP address: 192.168.1.80 (default IP)
Protocol: TCP(5000), UDP(4000)
RS232
Baud rate: 9600, N, 8, 1
Use RS232 direct cable
Commands
Functional description
Example
Yall.
Switch input Y to all
outputs
Switch 1 to all outputs: 1all.
YxY.
Switch input Y to output Y
Switch input 2 to output
9:2x9.
YxY.YxY.YxY.
Switch input Y to output
Ys
Switch input 3 to output 2, 3,
4:3x2.3x3.3x4.
SaveY.
Save to scene Y
Save to scene2: Save2.
Recall[y].
Recall the save scene Y
Recall to the scene 10:
Recall10.
Reset.
To reset account to admin/admin, IP address to default
192.168.1.80
8. Common Problem Shooting
Q: Serial port operation is out of order, can not control to switch?
A: The serial port is damaged or not started
Solution: Make sure the port uses direct serial port line, check the
connection of PC software serial port.
Power failure: Check the power fuses and connecting lines;
Signal interference: Make sure the cables and plugs are connected well,
the cables meet the requirements, the system is ground connected well,
the AC power between devices have the same grounding system;
Accidental damage：Sent back to the manufacturer for recondition.
9. After-Sales
9.1 Warranty Information
The Company warrants that the process and materials of the product are not
defective under normal use and service for 2 (2) years following the date of
purchase from the Company or its authorized distributors.
If the product does not work within the guaranteed warranty period, the
company will choose and pay for the repair of the defective product or
component, the delivery of the equivalent product or component to the user
for replacement of the defective item, or refund the payment which users
have made.
The replaced product will become the property of the Company.
The replacement product could be new or repaired.
Whichever is longer, any replacement or repaired of the product or
component is for a period of ninety (90) days or the remaining period of the
initial warranty. The Company shall not be responsible for any software,
firmware, information, or memory data contained in, stored in, or integrated
with the product repaired by the customer's return, whether or not during the
warranty period.
9.2 Warranty limitations and exceptions
Except above limited warranty, if the product is damaged by over usage,
incorrectly use, ignore, accident, unusual physical pressure or voltage,
unauthorized modification, alteration or services rendered by someone other
than the Company or its authorized agent, the company will not have to bear
additional obligations. Except using the product properly in the proper
application or normal usage.
/