Seamax Dolphin Installation guide

Brand: Seamax

Model: Dolphin

Type: Installation guide

Seamax Dolphin, the ultimate fishing companion, offers a secure and versatile rod holding system for your boat. With its adjustable ball clamp, you can customize the angle of your rod holders to suit your fishing style and target species. Whether you're trolling for walleye, casting for bass, or jigging for crappie, the Seamax Dolphin will keep your rods secure and ready for action. Made from high-quality materials, including a durable rubber collar for a snug fit on your T-top frame, the Seamax Dolphin is built to withstand the rigors of fishing and the marine environment.

1 | P a g e

Dolphin Rod Holder Installation Guide

EXPLODED VIEW OF THE DOLPHIN TWIN ROD HOLDERS

2 | P a g e

3 | P a g e

STEP 1: Unpack and check the contents of the box and check parts list.

Please Read all Instructions prior to installation. If you are NOT sure of any part of the guide or you have any

questions. Please contact the supplier or DOLPHIN T Tops

PARTS LIST

4 | P a g e

STEP 2: BALL CLAMP ASSEMBLY.

(A) Use two of the M6 bolts and attach the 2 x C sections of the clamp

together. If needed insert

the rubber collar around the inside of the ball clamp.

NOTE: The raised lip of the rubber collar will be nicely around at the

edge of the clamp. The edges of the joint should be "ush, if not turn one

of the c sections around.

STEP 3: ATTACHING THE BALL CLAMP TO THE TWIN ROD HOLDERS

(A) Attach the ball clamp to the twin rod holder by inserting the two locator lugs into holders on the

rod holder bracket. On the other side of the twin holders.

You insert the bolt through the hole and thread into the clamp and tighten.

NOTE: The clamp has two location lugs with a threaded center hole. The twin holder has a hole to insert

the bolt into the clamp. You can adjust what angle you require later.

5 | P a g e

STEP4: ATTACHING TWIN ROD HOLDERS TO T TOP.

NOTE: The clamp size is 2inch you will use the rubber collar to attach to the Dolphin T Top.

The outer lip of the rubber collar will be nice around the shape of the ball clamp.

On the Dolphin T Top there are 4 areas at the back of the top frame for locating your twin

rod holders - so you can have 8 rods across the back and if need there are position at the front.

Attaching the twin rod holders is simple and quick.

(A) Place the rubber collar around the t top frame. Put the half C section of the clamp on top of the

rubber collar. Then use the two bolts and attach to the other half of the clamp holding the rod holder.

You can rotate the clamp around the tube to angle the rod holders to the position you want. If you need

to angle the outer position rods away from the boat you can by adjusting the lugs in the clamp.

6 | P a g e

INSTALLATION GUIDE - Dolphin Twin Rod Holders.

WARNING:

Remove your rods when towing the boat behind your vehicle.

Ensure your rods will not bounce out of your holders whilst using your boat.

Check that your rod holders are tight before using your boat.

Care and maintain your racks. Clean with soapy water and rinse o" and dry.

Use a marine clear protection spray on bolts for best maintains.

WARRANTY

Indy warrants the product (not including other 3rd party accessories) against manufactures defects.

To claim you must contact Dolphin or its Distributor. The product/part is to be sent to the Distributor

for inspection where it will either be repaired or replaced. (Unless otherwise agreed in writing)

The customer is liable for costs associated in shipping the product/part to Dolphin T Tops.

Dolphin is not responsible for personal injury or damage to the boat caused by the use rod holders

or any transport charges or cost of installation or removal of the rod holders.

Dolphin is not liability for direct or indirect or consequential damages resulting from delay or improper

installation.

Warranty does NOT cover anodized, polished, powder coated surfaces as well as any hardware

corrosion, rubber collars or bungee cords. They are specially excluded as their care and use cannot

be controlled by Dolphin T Tops.

No dealer, retailer or manufacturer is the agent of James G Pty Ltd and may not assume any liability in

connection with this warranty. This warranty is in lieu of all.

Dolphin T Top Canada Distributor - Seamax Marine & Outdoor

102 – 19155 38 Ave, Surrey, BC, Canada V3Z 0Y6

www.seamaxmarine.com 1877-907-7766

SUPPORT@SEAMAXMARINE.COM

Seamax Dolphin Installation guide

Seamax Dolphin Installation guide

Seamax Dolphin Installation guide

Other documents