Troy-Bilt Troy-Bilt TB25C Curved Shaft String Trimmer User manual

Troy-Bilt
Brand
Troy-Bilt
Model
Troy-Bilt TB25C Curved Shaft String Trimmer
Type
User manual

This manual is also suitable for

Troy-Bilt Troy-Bilt TB25C Curved Shaft String Trimmer is a versatile and powerful tool designed to make yard work easier. With its curved shaft and trimmer head, it allows for precise trimming around obstacles and in hard-to-reach areas. The trimmer features a 25cc 2-cycle engine that delivers reliable power for tackling tough weeds and overgrown grass. It also comes equipped with a bump-feed trimmer line that automatically advances as needed, eliminating the need for manual adjustments.

Troy-Bilt Troy-Bilt TB25C Curved Shaft String Trimmer is a versatile and powerful tool designed to make yard work easier. With its curved shaft and trimmer head, it allows for precise trimming around obstacles and in hard-to-reach areas. The trimmer features a 25cc 2-cycle engine that delivers reliable power for tackling tough weeds and overgrown grass. It also comes equipped with a bump-feed trimmer line that automatically advances as needed, eliminating the need for manual adjustments.

IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW
THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT. Lea la traducción en Español en el manual.
NEED HELP? CALL 1-800-828-5500
ASSEMBLY TOOLS REQUIRED
• #2 Phillips screwdriver
778-16278 / 01 11/21
DIDN’T START?
Repeat the starting
instructions.
If the unit still fails to start,
refer to the operator’s
manual for additional starting
and troubleshooting
information.
PRIME:
Crouch in the starting position.
PRIME:
Pull the starter rope with a
controlled and steady motion 5
times.
DO NOT pull the starter rope
more than 5 times.
40:1
Mix thoroughly in a separate fuel
can:
– 3.2 fl. oz. of 2-cycle engine oil
– 1 gallon of fresh unleaded
gasoline (less than 30 days old)
NOTE: Do not mix directly in the
unit fuel tank.
START:
Move the choke lever to
Position 2.
Pull the starter rope with a
controlled and steady motion 5 to
10 times to start the engine.
Allow the engine to warm up for
60 seconds.
Position the unit with the fuel cap
facing up. Slowly remove the fuel
cap. Fill the fuel tank. Reinstall
the fuel cap. Move the unit at
least 30 ft. (9.1 m) from the fuel
container and the fueling site
before starting the engine.
89
356
Read the operator’s manual
thoroughly before operating
the unit. Follow all warnings and
safety instructions. This fast
guide is intended as a reference
for users that have already read
the operator's manual and are
familiar with the necessary safety
precautions.
1
Starter Rope Grip
Fuel Cap
Throttle Control
On / Off Switch
Choke Lever
Primer Bulb
PRIME:
Move the choke lever to
Position 1.
2
START:
Move the choke lever to
Position 3.
Allow the engine to warm up for
an additional 60 seconds. The
unit may be used during this time.
7
Handle
PRIME:
Slowly press and release the
primer bulb 10 times, or until
fuel is visible.
1
STARTING
Coupler
Upper Shaft
Housing
Insert the short tab (the one
without a hole) on the mount
bracket into the slot on the cutting
head shield. Rotate the cutting
head shield counterclockwise.
Insert the square bolt into the hole
underneath the cutting head shield.
Push the square bolt through the
cutting head shield and mount
bracket. Place the washer and
wing nut onto the square bolt.
Tighten the wing nut securely.
2 3
ASSEMBLY
Lower Shaft
Housing
Cutting Head Shield
Insert the screws (x2) into the
aligned holes. Tighten the screws
securely with a #2 Phillips
screwdriver.
Push the lower shaft housing into
the coupler. The holes on the
lower shaft housing should align
with the holes on the coupler.
NOTE: If the holes do not align,
remove the lower shaft housing,
rotate the cutting head slightly
(1/8th turn), and repeat this step.
4 5
Push the handle down onto the
upper shaft housing. Make sure
the hex hole faces left. Insert the
bolt into the hex hole. Place the
washer onto the bolt. Screw the
wing nut onto the bolt, but do not
tighten it completely.
6
Move the handle to a comfortable
location. Make sure the handle is
positioned beyond the end of the
safety label. Tighten the wing nut
until the handle is secure.
7
PRIME:
Squeeze and hold the throttle
control.
NOTE: Continue to SQUEEZE
and HOLD the throttle control
for ALL further steps.
4
Cutting
Head
  • Page 1 1

Troy-Bilt Troy-Bilt TB25C Curved Shaft String Trimmer User manual

Troy-Bilt
Brand
Troy-Bilt
Model
Troy-Bilt TB25C Curved Shaft String Trimmer
Type
User manual
This manual is also suitable for

Troy-Bilt Troy-Bilt TB25C Curved Shaft String Trimmer is a versatile and powerful tool designed to make yard work easier. With its curved shaft and trimmer head, it allows for precise trimming around obstacles and in hard-to-reach areas. The trimmer features a 25cc 2-cycle engine that delivers reliable power for tackling tough weeds and overgrown grass. It also comes equipped with a bump-feed trimmer line that automatically advances as needed, eliminating the need for manual adjustments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents