Wincor Nixdorf BEETLE /FUSION2nd HDD Kit Installation guide

BEETLE /FUSION

2

nd

HDD Kit

Installation Guide

The reproduction, transmission or use of this document or its contents is not

permitted without express authority.

Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model

or design, are reserved.

Delivery subject to availability; technical modifications possible.

BEETLE /FUSION 2

nd

HDD Kit

Installation Guide

Edition May 2011

Contents

BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

Contents

Introduction ..................................................................................................... 1

Symbols used in this guide ........................................................................... 1

Important safety precautions ........................................................................ 2

Installation notes ........................................................................................... 2

Installation ....................................................................................................... 3

Contents in kit ............................................................................................... 3

Tools required............................................................................................... 4

Installing harddisk to its guide rail................................................................. 5

Installing 2

nd

harddisk onto B/Fusion ............................................................ 6

Introduction

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 1

Introduction

This installation guide provides you with the information you require to

install the 2

nd

harddisk module onto the Beetle /Fusion system.

Symbols used in this guide

- Text following this mark represents an item in a list.

“ “ Text in quotation marks contains references to other chapters or

sections in this document.

● Paragraphs following this symbol are actions to be performed in the

specific order.

Text following this symbol has to be given special attention in order

to avoid damage or injury.

This symbol identifies paragraphs which contain general notes to

facilitate use of the device and help avoid operating errors.

i

Introduction

2 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

Important safety precautions

Please read the following notes carefully before doing any work on

the device.

Installation notes

When installing the device and/or doing any work on it, make sure

that it is disconnected from the power.

Take care for ESD protection when you are in contact with electronic

parts such as harddisk etc.

Repairs

Repair work may only be carried out by authorized personnel.

Unauthorized opening of the device or repair work carried out

improperly could result in considerable danger to the user.

In case of noncompliance, Wincor Nixdorf International GmbH

excludes all liability.

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 3

Installation

This chapter describes the steps to be taken to install the 2

nd

harddisk kit

onto the system.

Contents in kit

The following items are available in the upgrade kit:

· 1 qty of harddisk

· 1 set of harddisk guide rail (left and right side)

· 1 qty of harddisk mounting kit

· 1 qty of eSATA-SATA data cable

· 1 qty of SATA power cable

· 4 qty of counter sunk screws M3x6

· 4 qty of standoff

· 4 qty of cable ties

· 4 qty of adhesive plates

Installation

4 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

Tools required

· T10 Torx screwdriver

· T20 Torx screwdriver

· Nutdriver 5x5

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 5

Installing harddisk to its guide rail

· Ensure that the 2 guide rails are going to be snapped onto the

harddisk in the orientation shown in the picture below.

· Snap the harddisk to its 2 guide rail and leave it aside for use later

on (see picture below).

Installation

6 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

Installing 2

nd

harddisk onto B/Fusion

· Remove stand cover #2 by sliding it upwards (see picture below).

Remove cover

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 7

· Remove the four M4 screws using T20 screwdriver (see picture

below).

M4 screws

Installation

8 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

· Rotate B/Fusion panel PC until it is tilted to its maximum backward,

and remove the cover by pulling it in inward direction (see picture

below).

cover

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 9

· Lift B/Fusion panel PC unit to dislodge it from its desktop and place

it with its screen facing downward and make sure it is protected

from scratches.

Slide the cable cover in the directions indicated in the picture below

(1) & (2) and remove all cables that are attached to the panel PC unit

and routed through the desktop stand in order to detach panel PC

from the desktop stand (see picture below).

Note: Take note of the connections of the cables before removing them so

that they could be re-installed correctly later on.

1

2

Installation

10 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

· Remove the cover of the desktop stand with the instruction given in

the picture below.

Remove cover by pulling toward

this direction

Apply pressure at this

point while sliding the

cover out

Place your hand to pull

out the cover

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 11

· Remove the cover by pulling in the direction shown as the arrow in

the picture below.

· Remove the two screws to enable the cover to be removed, pull the

cover in the direction shown as the arrow in the picture below.

Remove screws

Installation

12 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

· Secure the four M3 standoff to the M3 threaded holes on the

desktop stand as shown in the picture below.

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 13

· Place the harddisk mounting bracket by aiming the mounting holes

towards the 4 stand-off and tighten the 4 counter sunk screws onto

the standoff (see picture below).

Tighten screws

Harddisk

mounting

bracket

Installation

14 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

· Slot the harddisk together with its 2 plastic guides into the harddisk

mounting bracket until it reaches a stop, take note of its orientation

(see picture below).

Installation

01750219504 A BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 15

· Connect the data cable and power cable to the hardisk (see picture

below). Route the cables according to the pictures shown below to

ensure the functionality of the system is not compromised.

Cable base must be

clear at the harddisk

slide entry area

Place cable base directly under

the SATA cable

Installation

16 BEETLE /FUSION 2

nd

HDD Kit – Installation Guide 01750219504 A

· Connect the harddisk cable to B/Fusion unit. (see picture below)

Harddisk

cable

Page is loading ...

Wincor Nixdorf BEETLE /FUSION2nd HDD Kit Installation guide

Wincor Nixdorf BEETLE /FUSION2nd HDD Kit Installation guide

Related papers

Other documents