Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
14
en Table of contents
Safety instructions ............................................. 15
Directions for disposal ..................................... 16
Specifications supplied .................................... 16
Installing the appliance .................................... 16
Connecting the appliance ................................ 17
Changing the door hinge ................................. 18
Getting to know the appliance ........................ 19
Switching on the appliance ............................. 20
Setting the temperature .................................... 20
Usable capacity ................................................. 20
Freezer compartment ....................................... 20
Freezing capacity .............................................. 20
Freezing and storing ......................................... 20
Freezing fresh food ........................................... 21
Defrosting frozen food ...................................... 21
Fittings ................................................................. 21
Switching off and shutting down
the appliance ..................................................... 22
Defrosting ........................................................... 22
Cleaning the appliance .................................... 22
Smells .................................................................. 23
Saving energy .................................................... 23
Operation noises ............................................... 23
Rectifying minor faults yourself ....................... 24
After-sales Service ............................................ 25
en
15
Safety instructions
This appliance complies with the relevant safety
regulations for electrical appliances and is fitted with
noise suppression.
The refrigeration circuit has been checked for leaks.
About these instructions
■ Read and follow the instructions for installation and
use. They contain important information on how to
install, use and maintain the appliance.
■ The manufacturer is not liable if you disregard the
notifications and warnings in the operating and
installation instructions.
■ Retain all documents for subsequent use or for the
next owner.
Risk of explosion
■ Never use electric appliances inside the appliance
(e.g. heaters or electric ice makers).
■ Do not store products which contain flammable
propellant (e.g. spray cans) or explosive substances
in the appliance.
■ Keep high-percentage alcohol tightly sealed and
store in an upright position.
■ Do not use additional means to accelerate the
defrosting process other than those recommended
by the manufacturer.
Risk of electric shock
Improper installations and repairs may put the user at
considerable risk.
■ When installing the appliance, ensure that the mains
cable is not trapped or damaged.
■ If the mains cable is damaged: immediately
disconnect the appliance from the electricity supply.
■ Do not use multi-outlet power strips, extension leads
or adapters.
■ Have the appliance repaired by the manufacturer,
Customer Service or a similarly qualified person only.
■ Use original parts supplied by the manufacturer only.
The manufacturer guarantees that these parts satisfy
the safety requirements.
Risk of cold burns
■ Never put frozen food straight from the freezer
compartment into your mouth.
■ Avoid prolonged contact between your skin and
frozen food, ice and the tubes in the freezer
compartment.
Risk of injury
Containers which contain carbonated beverages may
burst.
Do not store containers which contain carbonated
beverages in the freezer compartment.
Fire hazard/Danger due to
refrigerants
The tubes of the refrigeration circuit convey a small
quantity of an environmentally friendly but flammable
refrigerant (R600a). It does not damage the ozone
layer and does not contribute to the greenhouse effect.
If refrigerant escapes, it may injure your eyes or ignite.
■ Do not damage the tubes.
If the tubes are damaged:
■ Keep naked flames and ignition sources away from
the appliance.
■ Ventilate the room.
■ Switch off the appliance and pull out the mains plug.
■ Please contact Customer Service.
Fire hazard
Portable multi-outlet power strips or power supplies
may overheat, causing a fire.
Never leave portable multi-outlet power strips or
portable power supplies behind the appliance.
Avoiding placing children and vulnerable
people at risk
At risk here are:
■ Children,
■ People with limited physical, mental or sensory
abilities,
■ People who have inadequate knowledge concerning
safe operation of the appliance.
Measures:
■ Ensure that children and vulnerable people have
understood the hazards.
■ A person responsible for safety must supervise or
instruct children and vulnerable people who using
the appliance.
■ Only children aged 8 years and above may use the
appliance.
■ Supervise children who are cleaning and maintaining
the appliance.
■ Never allow children to play with the appliance.
Risk of suffocation
■ If the appliance features a lock: keep the key out of
the reach of children.
■ Keep children away from the packaging and its
parts.
Damage to property
To prevent damage to property:
■ Do not stand or support yourself on the base,
runners or doors.
■ Keep plastic parts and door seals free of oil and
grease.
■ Pull on the mains plug – not the power cord.
en
16
Weight
When installing and transporting the appliance, note
that it may be very heavy.
Intended use
Use this appliance
■ Only for freezing food and making ice.
■ Only in the home and in the home environment.
■ Only according to this user manual.
This appliance is intended for use up to a maximum
height of 2000 metres above sea level.
Directions for disposal
* Disposing of packaging
The packaging protects your appliance from damage
during transport. All the materials used are
environmentally friendly and can be recycled. Please
help by disposing of the packaging in an
environmentally responsible manner.
Information about the available disposal methods and
sites can be obtained from your appliance retailer or
your local authority.
* Disposing of your old appliance
Used appliances are not valueless waste. Valuable raw
materials can be recovered through environmentally
responsible disposal.
m Warning
Appliances at the end of their useful life:
1. Unplug the mains plug.
2. Cut the power cord and remove it along with the
mains plug.
3. Do not remove the shelves and containers. Leaving
them intact makes it more difficult for children to
climb in.
4. Never let children play with a disused appliance.
Risk of asphyxiation!
Refrigerators contain refrigerant as well as gases in the
insulation material. Refrigerant and gases must be
disposed of properly. Do not damage the refrigerant
circuit pipes before disposing of them properly.
Specifications supplied
After unpacking the appliance, check all parts for
transport damage.
If you find any defects, contact the retailer from whom
you purchased the appliance or our After-sales Service.
The appliance supplied consists of the following
components:
■ Free-standing appliance
■ Features (vary depending on the model)
■ Bag of assembly materials
■ Instructions for use and installation
■ Service record
■ Guarantee slip
■ Information on energy consumption and noise
Installing the appliance
Transport
Because of the weight and size of the appliance, and in
order to minimise the risk of personal injury or damage
to the appliance, at least two persons are required for
moving and positioning the appliance safely.
Installation site
The ideal installation site is a dry, well ventilated room.
The appliance should not be installed in a position that
is exposed to direct sunlight or close to a source of
heat, such as a cooker or radiator. If installation near to
a source of heat is unavoidable, use a suitable
insulating panel or keep to the following minimum
distances from the source of heat:
■ 3 cm from an electric or gas cooker.
■ 30 cm from oil or solid fuel cookers.
Floor surface
The floor at the installation site must not give. Reinforce
the floor if necessary.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances (waste
electrical and electronic equipment - WEEE).
The Directive determines the framework for the
return and recycling of used appliances as
applicable throughout the EU.
en
17
Wall clearance
If the appliance is positioned in the corner of a room or
a recess, minimum clearances at the sides must be
maintained so that the heated air is able to escape
unimpeded and the appliance door can be fully
opened.
Observe the room temperature and
ventilation requirements
Room temperature
The appliance is designed for a certain climate class.
Depending on the climate class, the appliance can be
operated at the following ambient temperatures.
The climate class is specified on the rating plate.
Note
The appliance is fully functional within the room
temperature limits of the specified climate class. If an
appliance in the SN climate class is operated at lower
ambient temperatures, damage to the appliance can be
excluded up to a temperature of +5 °C.
Ventilation
The heated air must be able to escape unimpeded.
Otherwise, the refrigerating unit has to work harder,
which increases the appliance's power consumption.
Therefore:
■ Never cover over or block the air vent.
■ Keep minimum distances to walls and furniture.
Connecting the appliance
After setting up the appliance, wait for at least 4 hours
before starting the appliance up. The oil contained in
the compressor may have been displaced into the
refrigeration system during transport.
Before starting the appliance up for the first time, clean
its interior (see section headed Cleaning the
appliance).
Electrical connection
The socket must be near to the appliance and easily
accessible after the appliance has been installed.
The appliance conforms to protection class I. Connect
the appliance to a 220-240 V/50 Hz alternating current
supply using a socket with protective earthing
conductor which has been correctly installed. The
socket must be protected by a fuse with a rating of
10 A to 16 A.
In the case of appliances operated outside of Europe,
check whether the voltage and type of current specified
conform to the values of your electricity grid. You will
find this information on the rating plate.
m Warning
The appliance must never be connected up to an
electronic energy-saving socket.
Sinusoidal-commutated and line-commutated inverters
can be used with our appliances. Line-commutated
inverters are used with photovoltaic systems that are
connected directly to the national grid. Sinusoidal-
communicated inverters must be used with standalone
applications (e.g. on ships or mountain huts) that do
not have a direct connection to the national grid.
Climate class Permissible room temperature
SN +10 °C to 32 °C
N +16 °C to 32 °C
ST +16 °C to 38 °C
T +16 °C to 43 °C
en
18
Aligning the appliance
Note
To ensure that it functions properly, the appliance must
be aligned using a spirit level.
1. Move the appliance into its intended installation
position.
2. Screw the feet in/out until the appliance is exactly
aligned.
Changing the door hinge
We recommend to have the door hinge changed by our
customer service. How much a door hinge change will
cost you can find out contacting customer service.
m Warning
When the door hinge is changed, the appliance must
not be connected to the power supply. Please pull the
mains plug beforehand.
Required tools
Changing door hinge of the appliance
door
1. Open the appliance door and unhinge and remove
all fittings from inside the appliance (see section
headed Fittings).
2. Unscrew the 2 screws (1).
3. Take off the cover plate (2) and set it down on a
soft surface.
Hold on to the appliance door!
4. Unscrew the 2 screws (3).
5. Unscrew the 2 screws (4).
6. Remove the top hinge (5).
7. Unhook the appliance door and set it down on a
soft surface.
8. To avoid damaging the appliance rear side, provide
cushioning material. Place the appliance carefully
onto its rear side.
8 mm hex nut driver
Cross-shaped screwdriver
Thin-blade screwdriver
en
19
9. Unscrew the feet (6).
10. Unscrew the 3 screws (7).
11. Remove the bottom hinge (8).
12. Unscrew the nut (9) and pull out the bolt (10).
13. Insert the bolt (10) into the left boring and apply the
nut (9) and tighten.
14. Apply the bottom hinge (8) and apply 3 the
screws (7) and tighten.
15. Screw the feet (6) into the bottom hinge (8).
16. Attach the appliance door to the bottom hinge (8).
17. Apply the 2 screws (4) and tighten.
18. Apply the top hinge (5) and apply the 2 screws (3)
and tighten.
19. Turn the appliance upright again.
20. Mount the cover panel (2) at the front and lay it flat
on the rear.
21. Apply the 2 screws (1) and tighten.
22. Open the appliance doors and attach all fittings
(see section headed Fittings).
Getting to know the appliance
Appliance
The features of the models may vary.
The illustrations may differ from your particular model.
1 Temperature controller
2 Upper frozen food container
3 Ice-cube tray
4 Medium frozen food container
5 Lower frozen food container
en
20
Switching on the appliance
Plug the mains plug into the mains outlet socket.
The appliance will start cooling.
Notes on using the appliance
■ After switching on the appliance, it may be several
hours before the set temperature is reached.
Do not put any food in the appliance before then.
■ If you cannot open the appliance door again
immediately after closing it, wait a moment for the
low pressure created to equalise.
Setting the temperature
Freezer compartment
Use a coin to turn temperature controller to the
required setting.
We recommend a medium temperature setting.
Set cooler temperatures only as a temporary measure
when large quantities of food are put into the freezer
compartment or when ice is produced.
Note
When a cooler temperature was set while the outside
temperature is higher, the cooling unit runs very
frequently or without interruptions. This results in higher
energy consumption.
Usable capacity
You will find the details of the usable capacity on the
rating plate inside the appliance.
Freezer compartment
Use the freezer compartment for the
following
■ Storing deep frozen food.
■ To make ice cubes.
■ To freeze food.
Note
Make sure that the appliance door is always closed.
When the appliance door is open, the frozen foods
defrost and the freezer compartment ices up heavily. In
addition: Energy is wasted due to the power
consumption.
Freezing capacity
You will find information on the freezing capacity on the
rating plate.
Freezing and storing
Purchasing frozen foods
■ Packaging must not be damaged.
■ Observe the best before date.
■ The temperature in the commercial chest freezer
must be -18 °C or colder.
■ As far as possible, frozen food must be transported
in an insulated container and quickly placed in the
freezer compartment.
When arranging the food, note the
following
Spread the items out well in the frozen food containers.
Note
Food that is already frozen must not come into contact
with the food that is to be freshly frozen.
Storing frozen food
Avoid contact between food and rear panel. Otherwise
the air circulation will be impaired.
Food or packaging could freeze to the rear panel.
cold: Warmer temperature
extra cold: Cooler temperature (higher energy
consumption)
en
21
Freezing fresh food
Only use fresh, undamaged food for freezing.
In order to retain the nutritional value, aroma and colour
of the food as much as possible, blanch vegetables
before they are frozen.
Blanching is not required for aubergines, peppers,
courgettes and asparagus.
You can find literature about freezing and blanching in
bookshops.
Note
Do not allow food that is to be frozen to sit right next to
food that has already been frozen.
■ The following are suitable for freezing:
Baked goods, fish and seafood, meat, game, poultry,
vegetables, fruit, herbs, eggs without their shells,
dairy products such as cheese, butter and curd
cheese, prepared dishes and leftovers such as
soups, stews, cooked meat and fish, potato dishes,
baked casseroles and sweet foods.
■ The following are not suitable for freezing:
Types of vegetable that are usually eaten raw, such
as lettuces or radishes, eggs in their shells, grapes,
whole apples, pears and peaches, hard-boiled eggs,
yoghurt, curds, soured cream, crème fraîche and
mayonnaise.
Packing frozen food
Pack food so that it is airtight to prevent it from losing
its flavour or drying out.
1. Store food in its packaging.
2. Press out any air.
3. Close the packaging tightly.
4. Label packaging with its contents and date of
freezing.
The following are suitable as packaging:
Plastic film, polyethylene hose film, aluminium foil,
freezer bags.
You will find these products at your specialist dealer.
The following are not suitable as packaging:
Wrapping paper, greaseproof paper, cellophane,
rubbish bags and used shopping bags.
The following are suitable for sealing packaging:
Rubber bands, plastic clips, pack-twines, cold-resistant
scotch tape, or similar.
Polyethylene bags and hose film can be fused closed
using a bag sealer.
Storage life of frozen foods
The storage life depends on the type of food.
At a temperature of -18 °C:
■ Fish, sausages, prepared dishes, baked goods:
Up to 6 months.
■ Cheese, poultry, meat:
Up to 8 months.
■ Vegetables, fruit:
Up to 12 months.
Defrosting frozen food
You can choose between the following options,
depending on the type of food and its intended use:
■ at ambient temperature
■ in the fridge
■ in an electric oven, with/without hot air convection
■ In the microwave oven.
m Caution
Do not refreeze defrosted food. It can only be refrozen
after it has been made into a ready-to-eat meal (cooked
or roasted).
Do not continue to use the complete max. storage time
for the frozen food.
Fittings
Frozen food container
The frozen food containers can be removed for loading
and unloading and cleaning.
en
22
Ice-cube tray
The ice-cube tray is for producing and keeping ice
cubes in.
1. Fill the ice-cube tray ¾ full of drinking water and
place in the frozen food container.
2. If the ice-cube tray is stuck to the freezer
compartment, loosen with a blunt implement only
(spoon-handle).
3. To loosen the ice cubes, twist the ice-cube tray
slightly or hold briefly under flowing water.
Switching off and shutting
down the appliance
Switch off the appliance
Unplug the appliance from the mains or switch off the
circuit-breaker.
Putting the appliance out of service
If you do not use the appliance for long periods:
1. Remove all food from the appliance.
2. Switch off the appliance.
3. Defrost the appliance.
4. Clean the appliance.
5. Leave the appliance door open.
Defrosting
Freezer compartment
A layer of frost in the freezer compartment impairs the
cooling effect on the frozen food and increases the
power consumption. If there is a layer of frost, you must
defrost the appliance.
General tips
■ When putting food in or taking food out, open the
appliance door for as little time as possible.
■ Do not install the appliance in a damp room. A high
level of humidity aids the formation of frost.
■ Package fresh food so that it is as air-tight as
possible.
m Caution
Do not scrape away the layer of ice using a knife or a
sharp object. You could damage the refrigerant pipes. If
refrigerant shoots out, it may ignite or cause eye
injuries.
Defrosting the appliance
1. Turn the temperature controller to the coldest
temperature approx. 3 hours before the defrosting
to ensure that the food is thoroughly frozen.
2. After 3 hours, switch off the appliance.
3. Take out the food and store it in a cool place. Place
blocks of ice (if you have one) on the food.
4. Leave the appliance door open.
5. Put a wiping cloth in front of the appliance to collect
water that might escape during the defrosting
process.
6. Wait until the layer of ice can be removed.
7. Remove the layer of ice, clean the freezer
compartment and wipe dry its inside.
8. Switch on the appliance and put the food back in.
Defrosting aids
To speed up the defrosting process, you can use a
plastic scraper to remove the layer of ice.
m Caution
Never use electrical appliances, defrosting sprays or
open flames to defrost the freezer, e.g. heaters, steam-
cleaning appliances, candles, oil lamps, etc. Do not
place any saucepans containing hot water in the
appliance in order to speed up the defrosting.
Cleaning the appliance
m Caution
■ Do not use gritty, acidic or chlorine-based cleaning
agents or solvents.
■ Do not use abrasive cleaning pads or sponges that
may scratch surfaces. This may lead to corrosion of
the metallic surfaces.
■ Never clean the containers in the dishwasher. The
parts may warp.
Proceed as follows:
1. Switch off the appliance before cleaning.
2. Unplug the appliance from the mains or switch off
the circuit-breaker.
3. Take out the food and store it in a cool place. Place
blocks of ice (if you have one) on the food.
4. Wait until the layer of frost has thawed out.
5. Clean the appliance with a soft cloth, lukewarm
water, and a little pH-neutral washing-up liquid. The
washing-up liquid solution must not be allowed to
run into the evaporation tray through the drain hole.
6. Only wipe the door seal with clean water and then
rub it until it is dry.
en
23
7. Clean the condensator, air intake and exhaust
opening with a brush or vacuum cleaner.
8. Clean the drain hole with a cotton swab.
9. After cleaning, reconnect the appliance to the
mains and switch it on.
10. Put the food back in.
Fittings
All the variable components of the appliance can be
removed for cleaning (see section headed Fittings).
Smells
If you notice unpleasant smells:
1. Switch off the appliance.
2. Remove all food from the appliance.
3. Clean the inside of the appliance (see section
headed Cleaning the appliance).
4. Clean all packaging.
5. Pack strongly smelling food in air-tight containers to
prevent odours.
6. Switch on the appliance again.
7. Arrange the food.
8. After 24 hours, check again to see if the smells
have reappeared.
Saving energy
■ Install the appliance in a dry, well ventilated room.
The appliance must be installed out of direct sunlight
and away from heat sources (e.g. heating elements,
cooker).
Use an insulating plate if necessary.
■ Allow hot food and drinks to cool before placing
them in the appliance.
■ Place frozen food in the fridge compartment to
defrost and utilise the low temperature of the frozen
food to cool other food.
■ Only open the appliance door for as short a time as
possible.
■ To prevent the food warming up quickly in the event
of a power cut or a fault, place blocks of ice (if you
have one) on the food.
■ Make sure that the appliance door is always closed.
■ The arrangement of the equipment parts shown in
the section Getting to know the appliance requires
the least amount of energy. Any other arrangements
can result in higher energy consumption.
■ To prevent increased power consumption,
occasionally clean the air vent with a soft brush or
vacuum cleaner.
Operating noises
Completely normal noises
Humming
Motors running (e.g. refrigeration units, ventilator).
Bubbling, whirring or gurgling noises
Refrigerant circulating through the pipes.
Clicking
Motors, switches or solenoid valves are switching on/
off.
Preventing noises
The appliance is not standing straight
Make sure the appliance is exactly aligned by using a
spirit level. To adjust the position of the appliance, use
the adjustable feet or place something underneath.
The appliance is touching adjacent units or
appliances
Move the appliance away from adjacent furniture or
appliances.
Containers or shelves are wobbling or sticking
Check the removable parts and re-insert them if
necessary.
Containers are touching
Move the containers apart slightly.
en
24
Rectifying minor faults yourself
Before calling After-sales Service:
Check whether you can rectify the fault yourself by using the notes below.
You must pay the cost of the After-sales Service call out – even during the guarantee period.
Problem Possible cause Remedy
Appliance is not cooling/
freezing.
Power cut. Check whether there is power to the
appliance.
Circuit-breaker is switched off. Check circuit-breaker.
Power plug not properly plugged in. Check whether power plug is properly
plugged in.
The refrigeration unit switches
on with increasing frequency
and for longer periods.
The appliance door is being opened
frequently.
Do not open the appliance door
unnecessarily.
The ventilation openings are covered. Remove any obstructions.
Placing large quantities of food in the
appliance.
Set a lower temperature.
The temperature setting is too low. Set a higher temperature.
The appliance is too close to a heat
source or the ambient temperature is
too warm.
See section headed Installing the appliance.
The freezer compartment is too
warm.
The appliance door is being opened
frequently.
Do not open the appliance door
unnecessarily.
Placing large quantities of food in the
appliance.
Set a lower temperature.
The temperature setting is too high. Set a lower temperature.
The appliance is too close to a heat
source or the ambient temperature is
too warm.
See section headed Installing the appliance.
The freezer compartment is too
cold.
The temperature setting is too low. Set a higher temperature.
Unpleasant smells are
noticeable.
Strongly smelling food not packed in
air-tight containers.
Clean the appliance. Pack strongly smelling
food in air-tight containers (see section
headed Smells).
In the appliance a layer of ice
is forming.
The ventilation openings are covered. Remove any obstructions.
The appliance door was not closed
completely.
Close the appliance door completely.
The door seal is dirty. Clean the door seal. See section headed
Cleaning the appliance.
The appliance door can only
be closed with difficulty.
Food prevent the appliance door from
closing correctly.
Remove any obstructions.
The appliance is not aligned. Align the appliance with a spirit level. See
section headed Aligning the appliance.
After a cooler temperature was
set, the cooling machine does
not switch on immediately.
This is normal, there is no fault.
On the appliance bottom water
has accumulated.
The drain hole is plugged. Clean the drain hole with a cotton swab.
See section headed Cleaning the appliance.
en
25
After-sales Service
You can find your local After-sales Service centre in the
phone book or the After-sales Service directory. Please
quote the product number (E-Nr.) and production
number (FD-Nr.) of your appliance.
You will find this information on the rating plate.
Please help us to avoid unnecessary journeys by
quoting the appliance and production number. By
doing so, you will save any associated additional
charges.
Booking a repair call-out and advice on
faults
The After-sales Service contact details for all countries
are listed in the attached After-sales Service directory.
GB 0344 892 8979 Calls charged at local or
mobile rate.
IE 01450 2655 0.03 € per minute at peak.
Off peak 0.0088 € per
minute.
US 800 944 2904 toll-free
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/