Brunton Download Owner's manual

ALL NIGHT

HIGH CAPACITY POWER SUPPLY WITH

INTEGRATED LIGHTING SYSTEM FOR GOPRO®

F-ALLNIGHT-BK

F-ALLNIGHT-YL

QUICK START GUIDE

COMPATIBLE WITH HERO™, HERO™3+ AND HERO™ 4 MODELS.

THE ALL NIGHT WILL NOT FIT OTHER MODELS. HERO™3 IS COMPATIBLE WHEN

USED WITH HERO™3+ OR HERO™4 CASE. GOPRO®, HERO®,

THE GOPRO® LOGO AND THE GOPRO® BE A HERO LOGO ARE TRADEMARKS OR

REGISTERED TRADEMARKS OF GOPRO®, INC.

BR-Manual-ALL-NIGHT 7.0.indd 1 10/12/15 10:00 AM

2 3

SIDE DOOR:

Micro-USB Input

(Charge ALL NIGHT)

USB Output

(Charge other devices)

Power Button

BACK:

USE (2.)USB OUTPUT

FOR HERO™ CAMERA

USE (1.) USB OUTPUT FOR

HERO™ 3 AND 4 SERIES CAMERAS

(3.)USB PLUG STORAGE

WHEN NOT IN USE

1

23

Light Color: Power Level:

RED/OFF >30% (Flashing—Needs charge)

GREEN 30–100%

(Solid light indicates ALL NIGHT is charging)

OPERATING THE INTEGRATED LIGHTING

SYSTEM

The ALL NIGHT has been carefully designed to allow the capture of video in a wide

variety of low light conditions. It has multiple light mode settings to allow the best

capture depending on different environmental conditions. Due to the added weight of

the ALL NIGHT, it is suggested that a phillips head screwdriver be used on the GOPRO®

mount tightening screw (See A Below).

TO TURN LIGHT ON/OFF: Press and hold power button for 2 seconds until light turns

on or off.

1

2

3

A

1. Light Power/Function Button

2. Mode Indicator Lights (On Back Of Metal Housing)

3. Metal Housing

TO CHANGE LIGHT MODE: Press button for 1 second or less. NOTE: When light is

turned off, it will turn on in last light mode setting so user does not have to cycle

through modes to select current mode.

POWER FORWARD

The ALL NIGHT extends the power of your HERO™, HERO™3+ and HERO™ 4 models to

more than 5X the specified run-time of the standard battery alone supplied with

your GOPRO® while still offering the rugged, waterproof* performance your camera

requires.

1. Remove existing GOPRO® case back and travel cover from ALL NIGHT By opening

door and pulling straight down out of brackets. Do not remove pin from door.

2. Snap on ALL NIGHT.

3. Attach flat USB cable plug to camera’s USB input port using specified mini-USB

outlet depending on camera type (see back diagram below). Attach opposite end of

flat cable to camera’s mini-USB power input port and close case. Ensure cable is

not caught in door when closed.

4. Open side door, press ALL NIGHT power button. Shoot longer .

1. 2. 3. 4.

* This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing GOPRO®

in the case before EVERY use and ensure side access door latch is fully engaged. Brunton

is NOT responsible for camera damage while using Brunton products.

POWER UP

Open ALL NIGHT side access door and press power button to supply power to camera.

Charging indicator LED on camera will light to the status of the battery, red or green.

Press again to power off ALL NIGHT.

The ALL NIGHT can charge your smartphone or other USB charged device while

powering your GOPRO® camera at the same time. It can also be used as a convenient,

portable, stand-alone power source so you never have to power down. When used as a

portable power bank, please make sure travel cover is snapped onto the ALL NIGHT.

To use, open Patented side access door and plug USB powered device into USB output

port.

3. Micro-USB Input

(Charge ALL NIGHT)

1. USB Output

(Charge other devices)

2. Power Button

When closing side door, ensure latch is engaged to create waterproof seal.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

To recharge the ALL NIGHT, connect micro-USB input cable to a running computer, USB

outlet, or a Brunton portable power device. A solid red light on the battery level LED

indicator indicates that the ALL NIGHT is charging.

BR-Manual-ALL-NIGHT 7.0.indd 2-3 10/12/15 10:00 AM

4 5

____________________________________________________________________________________

ALLEZ DE L’AVANT

L’appareil ALL NIGHT augmente l’autonomie des modèles HERO

MC

, HERO 3+

MC

et

HERO 4

MC

jusqu’à plus de 5X la durée de fonctionnement indiquée pour la batterie

standard fournie avec le GOPRO

MC

tout en offrant la même robustesse et la même

résistance à l’eau* que le fonctionnement de cette caméra exige.

1. Enlevez l’arrière du boîtier de l’appareil GOPRO

MC

et la plaque de transport du ALL

NIGHT en ouvrant la porte d’accès et en tirant vers le bas pour la sortir de ses

gonds. N’enlevez pas la goupille de la porte.

2. Fixez le ALL NIGHT par pression

3. Fixez le connecteur plat du câble USB à la borne d’entrée USB de la caméra en

utilisant la sortie mini-USB désignée selon le type de caméra (voir le schéma arrière

ci-dessous). Fixez l’autre extrémité du câble plat à la borne d’entrée mini-USB de

la caméra et refermez le boîtier. Assurez-vous que le câble n’est pas coincé dans la

porte lorsque celle-ci est fermée.

4. Ouvrez la porte d’accès latérale et enfoncez la touche de mise en marche de l’ ALL

NIGHT. Enregistrez plus longtemps.

1. 2. 3. 4.

* Ce produit résiste à l’eau jusqu’à une profondeur de 40 mètres. Vérifiez l’étanchéité

de la batterie et du boîtier pour déceler des fuites AVANT de placer la GOPRO

MD

dans le boîtier et avant CHAQUE utilisation et assurez-vous que le fermoir de la

porte d’accès latérale est bien en place. Brunton N’EST PAS responsable pour des

dommages à la caméra lors de l’utilisation des produits Brunton.

METTEZ L’APPAREIL SOUS TENSION

Ouvrez la porte d’accès latérale du ALL NIGHT et enfoncez la touche de mise en marche

pour alimenter la caméra. L’indicateur de charge DEL de la caméra passera au rouge.

Enfoncez la touche de nouveau pour mettre hors tension.

Le ALL NIGHT peut charger votre téléphone intelligent ou d’autres appareils à

chargement USB tout en alimentant votre caméra GOPRO

MD

simultanément. Il peut

aussi être utilisé comme un bloc d’alimentation portable, autonome et pratique pour

ne pas avoir à mettre vos appareils hors tension. Lorsqu’il est utilisé comme bloc

d’alimentation, assurez-vous que la plaque de transport est bien fixée au ALL NIGHT.

5

6

7

Pour utiliser, ouvrez la porte d’accès latérale brevetée et branchez votre appareil

alimenté par USB dans la sortie USB .

MODE BEAM ANGLE LUMENS RUNTIME (HRS)

SPOT NARROW BEAM 350 High / 70 Low 11 High / 100 Low

FLOOD WIDE BEAM 50 High / 10 Low 22 High / 146 Low

SPOT/FLOOD

(BOTH LED’S

ILLUMINATED)

BOTH NARROW AND

WIDE

(BRIGHTEST SETTING)

400 High /

80 Low

8 High /

71 Low

HIGH INDICATES SELECTED MODE ON HIGH SETTING

LOW INDICATES SELECTED MODE ON LOW SETTING

CAUTION: WHEN USED IN SPOT/FLOOD MODE, METAL HOUSING CAN GET VERY HOT.

Run times are based on light usage alone. Camera operation will reduce run time

depending on frequency and duration of camera use and capture settings. For best

results, experiment with different camera and lighting setting combinations in

different environmental conditions.

NOTES AND SPECIFICATIONS:

• Rechargeable Lithium-Polymer Battery: 5000 mAh/18.5WH

• Micro-USB Input: 5V/1 A

• USB Output: 5V/2.1 A; Output to Camera: 5V/2.1A

WARNING

Read all instructions and warning prior to using this product. Improper use of this

product may result in product damage (including damage to your GOPRO® camera),

excess heat, toxic fumes, fire or explosion, for which damages you (“Purchaser”), and

not Brunton (“Manufacturer”) are responsible.

• Do not short-circuit disassemble or expose to fire.

• This product is waterproof up to 40M. Test battery/case for leaks BEFORE placing

GOPRO® in the case before EVERY use and ensure side access door latch is fully

engaged. Brunton is NOT responsible for camera damage while using Brunton

products.

• Do not expose to temperatures greater than 60˚C/140˚F.

• Recycle according to local regulation.

A complete list of tips and troubleshooting is at www.brunton.com.

WARRANTY

Please register your ALL NIGHT by visiting www.brunton.com/Register. Brunton has

taken every effort to ensure years of trouble-free use from your new product. This

product is guaranteed to be free of defect in material and workmanship according to

local regulatory requirements. This product is not subject to guarantee from third-

parties and is subject to change. Brunton will repair or replace with a new equivalent,

without charge for parts or labor, per Brunton’s discretion. Brunton cannot be held

responsible for accidents, damages or injury occasioned by the use of this product.

Warranty will be rendered invalid if product is damaged by tampering, negligence or

misuse. This warranty relates only to Brunton products and does not cover damage

to any attached products from other manufacturers. This product is waterproof up to

40M. Test battery/case for leaks BEFORE placing GOPRO® in the case before EVERY use

and ensure side access door latch is fully engaged. Brunton is NOT responsible for

camera damage while using Brunton products.

BR-Manual-ALL-NIGHT 7.0.indd 4-5 10/12/15 10:00 AM

Page is loading ...

1900 Taylor Avenue

Louisville, CO, 80027

800-443-4871

BRUNTON.COM

info@bruntongroup.com

GOPRO®, HERO, the GOPRO® logo, and the GOPRO® Be a Hero logo are trademarks or

registered trademarks of GOPRO®, Inc.

BR-Manual-ALL-NIGHT 7.0.indd 44 10/12/15 10:00 AM

Brunton Download Owner's manual

This manual is also suitable for

Brunton Download Owner's manual

in other languages

Related papers

Other documents