Insignia NS-HFMOC101 Quick setup guide

Insignia
Brand
Insignia
Model
NS-HFMOC101
Category
Office & computer chairs
Type
Quick setup guide
Quick Setup Guide
|
NS-HFMOC101
Flex Mesh Oce Chair
PACKAGE CONTENTS
Before using your new product, please read these instructions to prevent any damage.
ASSEMBLING YOUR CHAIR
Insert the wheels (D) into the star base (C). Keep pushing the wheels in until the metal rims touch the star
base.
Place the seat plate (G) on the seat bottom assembly as shown. Insert four 1/4 × 20 mm screws (H) with
four washers (J) into the seat plate. Tighten them with the Allen wrench. You may need to use the
short side of the wrench to get more leverage.
Place the chair assembly onto the gas lift until it is fully inserted.
Quick Setup Guide
FEATURES
• Adjustable height
• Lockable chair back
Place the star base cover (A) over the star base (C), then insert the gas lift (B) into the star base. Push the
gas lift in so that it is secure.
4
Allen wrench (1)
Screws
1/4 × 20 mm (4)
Screws
1/4 × 40 mm (4)
Washers
φ6 mm (4)
Caps
(4)
Seat plate (1)
Wheels (5)
Back (1)
Arms and seat bottom (1)
Star base (1)Gas lift (1)Star base cover (1)
3
V1 ENGLISH 15-0662
SPECIFICATIONS
• Weight: 32.85 lbs. (14.9) kg)
ONE-YEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico)
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies.
Distributed by Best Buy Purchasing, LLC
©2015 Best Buy. All rights reserved.
Made in China
USING YOUR CHAIR
• To raise the height of the chair, lift the lever on the right side while not sitting in the chair. To lower the height
of the chair, raise the same lever while sitting in the chair.
• To lock the back of the chair, push the left lever backward. To unlock the chair, pull the left lever forward.
SAFETY INFORMATION
• Maximum weight capacity: 250 lbs (113 kg).
• Read the instruction sheet completely before assembly.
• Remove all parts from carton and make sure that all parts are included prior to assembly.
• Assemble the chair on the carton or carpet to prevent scratching the chair.
• This chair is designed for sitting on the seat only and nothing else.
• Do not stand on or use as a step ladder.
• Do not sit on the armrests.
• This chair is designed for seating one person at a time.
• Tighten all screws, knobs, bolts, and parts rmly, otherwise do not use.
• If any parts are missing, damaged, or worn, stop using immediately.
• Do not use power tools.
5
Place the back (F) against the arms and insert the four 1/4 × 40 mm screws (I) into the back of the arms.
Tighten with the Allen wrench. Place the caps (K) over the screws. Your chair is now assembled.
37.5 in.
(95.5 cm)
18.5 in.
(47 cm)
13.5 in. (34.3 cm)
17.5 in. (44.5 cm)
28.5 in. (72.4 cm)
18.5 in. (47 cm)
  • Page 1 1
  • Page 2 2

Insignia NS-HFMOC101 Quick setup guide

Insignia
Brand
Insignia
Model
NS-HFMOC101
Category
Office & computer chairs
Type
Quick setup guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents