Ariston PF 631 E (WH) Owner's manual

Page is loading ...

10

A. Gas Burners

B. Support Grid for Cookware

C. Control Knobs for Gas Burners and Electric Hot

Plate

D. Ignitor for Gas Burners (only on certain models)

E. Ignition Button for Gas Burners (only on certain

models)

F. Safety Device (only on certain models) - Activates if

the flame accidentally goes out (spills, drafts, etc.),

interrupting the delivery of gas to the burner.

G. Electric Hot Plate (only on certain models)

H. Indicator Light for Electric Hot Plate (only on certain

models)

How To Use Your Appliance

Close-up View

The position of the corresponding gas burner or electric

hot plate (if present) is indicated on each control knob.

Gas Burners

The burners differ in size and power. Choose the most

appropriate one for the diameter of the cookware being

used.

The burner can be regulated with the corresonding control

knob by using one of the following settings:

• Off

High

Low

To turn on one of the burners, place a lighted match or

lighter near the burner, press the knob all the way in and

turn it anti-clockwise to the "High" setting.

On those models fitted with a safety device (F), the

knob must be pressed in for about 4 seconds until the

device that keeps the flame lit warms up.

On those models fitted with an ignitor (D), the "E"

ignition button, identified by the symbol, must first

be pressed and then the corresponding knob pushed

all the way in and turned anti-clockwise to the "High"

setting.

Some models are equipped with an ignition button

incorporated into the control knob. If this is the case, the

ignitor (D) is present, but not the "E" button (the symbol

is located near each knob).

To light the selected burner, first press the corresponding

knob down fully, turn it anti-clockwise to the high flame

symbol, and keep the knob pressed down until the

burner ignites for approximately 3-4 seconds to allow

the safety device "F", which keeps the flame lit

automatically, to heat up.

To turn off a burner, turn the knob clockwise until it stops

(it should be on the “•” setting).

Caution: If the burner accidently goes out, turn off the

gas on the control knob and wait at least 1 minute before

you try to to light it again.

Electric Hot Plate (only on certain models)

The hot plate can be: "normal" and "fast". The latter can

be identified by a red boss in the center of the hot plate

itself.

The hot plate can be regulated by turning the

corresponding knob in the clockwise or counter-clockwise

direction to any one of the 6 different settings:

0 Off

1 Low

2-5 Medium

6 High

The section entitled, "Practical Cooking Advise", provides

information on the recommended settings for various types

of food or cooking processes.

Congratualtions on choosing an Ariston appliance, which you will find is dependable and easy to use. We recommend

that you read this manual for best performance and to extend the life of your appliance. Thank you.

CHE

B

A

G

D

F

11

When the knob is on any of the settings other than "Off",

the "H" operating light comes on.

Before cleaning or performing maintenance on your

appliance, disconnect it from the electrical power supply.

To extend the life of the cooktop, it is absolutely

indispensable that it be cleaned carefully and

thoroughly on a frequent basis, keeping in mind the

following:

· Do not use steam equipment to clean the appliance.

· Remove any liquid from the lid before opening it.

• The enameled parts and the glass top, if present, must

be washed with warm water without using abrasive

powders or corrosive substances which could ruin

them;

• The removable parts of the burners should be washed

frequently with warm water and soap, making sure to

remove caked-on substances;

• On cooktops with automatic ignition, the end of the

electronic ignition device must be cleaned carefully and

frequently, making sure that the gas holes are not

clogged;

• The electric hobs should be cleaned using a damp cloth

and then rubbed with oil while still warm;

• Stainless steel can be stained if it remains in contact

with highly calcareous water or aggressive detergents

(containing phosphorous) for an extended period of

time. It is recommended that these parts be rinsed

thoroughly with water and then dried well. It is also a

good idea to clean up any spills.

Greasing the Taps

The taps may jam in time or they may become difficult to

turn. If so, the tap itself must be replaced.

N.B.: This operation must be performed by a technician

authorised by the manufacturer.

How to Keep Your Cooktop in Shape

Practical Advise on Using the Burners

For best performance, follow these general guidelines:

• Use the appropriate cookware for each burner (see

table) in order to prevent the flame from reaching the

sides of the pot or pan;

• Alwasy use cookware with a flat bottom and keep the

lid on;

• When the contents come to a boil, turn the knob to

"Low".

Burner ø Cookware diameter (cm)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

Triple Crown (TC) 24 - 26

Practical Advice

Practical Advice on Using the Electric Hot Plates

In order to avoid heat loss and damage to the hot plate,

use cookware with a flat bottom the diameter of which is

not less than that of the hot plate.

Setting Normal or Fast Plate

0

Off

1

Cooking vegetables, fish

2

Cooking potatoes (using steam) soups,

chickpeas, beans.

3

Continuing the cooking of large quantities

of food, minestrone

4

For roasting (average)

5

For roasting (above average)

6

For browning and reaching a boil in a

short time.

Before using the hot plates for the first time, you

should heat them at maximum temperature for

approximately 4 minutes, without any pans. During

this initial stage, their protective coating hardens and

reaches its maximum resistance.

12

Is there a problem?

The burner does not remain on when set to "Low".

Check to make sure that:

• The gas holes are not clogged.

• There are no draughts near the cooking surface.

• The minimum has been adjusted correctly (see the

section entitled, "Minimum Regulation").

The cookware is not stable.

Check to make sure that:

• The bottom of the cookware is perfectly flat.

• The cookware is centered correctly on the burner or

electric hot plate.

• The support grids have not been inverted.

If, despite all of these checks, the cooktop does not

function properly and problem persists, call the nearest

Customer Service Centre, informing them of:

- The type of problem.

- The abbreviation used to identify the model (Mod. ...) as

indicated on the warranty.

Never call upon technicians not authorized by the

manufacturer, and refuse to accept spare parts that are

not original.

It may occur that the cooktop does not function or does

not function properly. Before calling customer service for

assistance, lets see what can be done.

First of all, check to see that there are no interruptions in

the gas and electrical supplies, and, in particular, that the

gas valves for the mains are open.

The burner does not light or the flame is not uniform

around the burner.

Check to make sure that:

• The gas holes on the burner are not clogged;

• All of the movable parts that make up the burner are

mounted correctly;

• There are no draughts around the cooking surface.

The flame does not stay lighted on the model with

the safety device.

Check to make sure that:

• You press the knob all the way in;

• You keep the knob pressed in long enough to activate

the safety device.

• The gas holes are not clogged in the area

corresponding to the safety device.

13

Safety Is a Good Habit to Get Into

• This manual is for a class 3 built-in cooktop.

• This appliance is designed for non-professional use in

the home and its features and technical characteristics

must not be modified.

• These instructions are only valid for the countries the

symbols for which appear on the manual and the serial

plate.

• The electrical system of this appliance is safe only when

it is correctly connected to an adequate earthing

system, as required by current safety standards.

Prevent children and the disabled from coming into

contact or having access to the following, as they

are possible sources of danger:

- The controls and the appliance in general;

- The packaging (plastic bags, polystyrene, nails, etc.);

- The appliance, during and immediately after use given

the heat generated by its use;

- The appliance when no longer in installed (in this case,

all potentially dangerous parts must be made safe).

The following should be avoided:

- Touching the appliance with wet parts of the body;

- Using the appliance with bare feet;

- Pulling on the appliance or the power supply cord to

disconnect them from the electrical outlet;

- Improper and/or dangerous use;

- Obstructing the ventilation or heat dissipation slots;

- Allowing the power supply cord of small appliances to

come into contact with the hot parts of the cooktop;

- Exposure to atmospheric agents (rain, sun);

- Using flammable liquids nearby;

- Using adaptors, multiple outlet plugs and/or extensions;

- Using unstable or deformed cookware;

- Leaving the electric hobs on without cookware on top

of them;

- Closing the glass top (if present) while the gas burners

or electrical hot plates are still hot;

- Trying to install or repair the appliance without the

assistance of qualified personnel.

The assistance of qualified personnel must be called

upon in the following cases:

- Installation (in accordance with the manufacturer's

instructions);

- When in doubt about the operation of the appliance;

- Replacement of the electrical outlet becuase it is

incompatible with the plug.

Contact service centers authorized by the

manufacturer in the following cases:

- When in doubt about the condition of the appliance

after having removed the packing;

- Damage to or replacement of the power supply cord;

- In the case of a breakdown or malfunction: ask for

original spare parts.

It is recommended that you follow the guidelines

below:

- Only use the appliance to cook food, avoiding all other

uses;

- Check the condition of the appliance after it has been

unpacked;

- Disconnect the appliance from the power supply in the

event of malfunction and always before cleaning or

maintenance;

- When not in use, disconnect the appliance from the

power supply and turn off the gas valve (if present);

- Always check to make sure that the control knobs are

on the “•”/”o” setting when the appliance is not in use;

- Cut the power supply cord after disconnecting it from

the electrical mains when you decide to no longer use

the appliance.

• The manufacturer will not be held liable for any

damages arising out of : incorrect installation or

improper, incorrect or unreasonable use..

To maintain the EFFICIENCY and SAFETY of this appliance, we recommend:

• call only the Service Centers authorized by the manufacturer

• always use original Spare Parts

14

Installation Instructions for built-in

The following instructions are intended for the installer so

that the installation and maintenance procedures may be

followed in the most professional and expert manner possible.

Important: Disconnect the appliance from the electrical

supply before performing any maintenance or regulation

upkeep work.

Positioning the Cooktop

Important: this unit may be installed and used only in

permanently ventilated rooms in accordance with British

Standard Codes Of Practice: B.S. 6172 / B.S. 5440, Par. 2

and B.S. 6891 Current Editions. The following requirements

must be observed:

a) The room must be fitted with a ventilation system which

vents smoke and gases from combustion to the outside.

This must be done by means of a hood or electric

ventilator that turns on automatically each time the hood

is operated.

In a chimney stack or branched flue. Directly to the Outside

(exclusively for cooking appliances)

b) The room must also allow for the influx of the air needed

for proper combustion. The flow of air for combustion

purposes must not be less than 2 m³/h per kW of

installed capacity. The supply of said air can be effected

by means of direct influx from the outside through a

duct with a inner cross section of at least 100 cm² which

must not be able to be accidentally blocked. Those

appliances which are not fitted with a safety device to

prevent the flame from accidentally going out must have

a ventilation opening twice the size otherwise required,

i.e. a minimum of 200 cm² (Fig. A). Otherwise, the room

can be vented indirectly through adjacent rooms fitted

with ventilation ducts to the outside as described above,

as long as the adjacent rooms are not shared areas,

bedrooms or present the risk of fire (Fig. B).

Detail A Adjacent Room to be

Room Vented

A

Examples of ventilation holes Enlarging the ventilation slot

for comburant air. between window and floor.

Fig. A Fig. B

c) Intensive and prolonged use of the appliance may ne-

cessitate supplemental ventilation, e.g. opening a

window or increasing the power of the air intake system

(if present).

d) Liquidified petroleum gases are heavier than air and,

as a result, settle downwards. Rooms in which LPG

tanks are installed must be fitted with ventilation

openings to the outside in order to allow the gas to

escape in the event of a leak. Therefore, LPG tanks,

whether empty or partially full, must not be installed or

stored in rooms or spaces below ground level (cellars,

ect.). It is also a good idea to keep only the tank

currently being used in the room, making sure that it is

not near sources of heat (ovens, fireplaces, stoves,

etc.) that could raise the internal temperature of the

tank above 50°C.

Installation of Built-in Cooktops

The appliance can be installed next to furniture units which

are no taller than the top of the cooker hob. The wall in

direct contact with the back panel of the cooker must be

made of non-flammable material. During operation the

back panel of the cooker could reach a temperature of

50°C above room temperature. For proper installation of

the cooker, the following precautions must be taken:

a) If the cabinet(s) located next to the cooktop are higher

than the cooktop itself, the cabinet(s) must be installed at

least 600 mm from the edge cooktop;

b) Hoods must be installed in accordance with the

instructions contained in the installation manual for the

hoods themselves, and no less than 650 mm from the

cooktop;

c) In the case of the 600 mm cooker hoods, besides following

the recommendations in point b), the cabinets should be

positioned next to the hood at a height of at least 540 mm

from the top since this will make it possible to install the

lid and move it correctly. The cabinet should always be

installed at a height from the top which allows easy use

of pots and pans on the cooker.

d) Should the cooktop be installed directly under a cupboard,

the latter should be at least 700 mm (millimetres) from

the top, as shown in Figure.

600mm min.

540mm min.

700mm min.

e) The dimensions of the cutout for the appliance must be

those indicated in the figure. Clamps are provided to fasten

the cooktop to counters measuring from 20 to 40 mm in

thickness. To fasten the cooktop securely, it is

recommended that all the clamps be used.

15

555

mm

475

mm

55

mm

Fastening Clamps - Assembly Diagram

Clamp Position for Clamp Position for

H=20mm top H=30mm top

Front

Clamp Position for

H=40mm top Back

N.B: Use the clamps contained in the "accessory kit."

f) In the event the cooktop is not installed above a built-in

oven, a wood panel must be inserted as insulation. This

panel must be placed at least 20 mm from the bottom of

the cooktop itself.

Important: When installing the cooktop above a built-in oven,

the oven should be placed on two wooden strips; in the case

of a joining cabinet surface, remember to leave a space of at

least 45 x 560 mm at the back.

560 mm.

45 mm.

When installing the cooktop above a built-in oven without

forced ventilation, ensure that there are air inlets and outlets

for ventilating the interior of the cabinet adequately.

Gas Connection for Cooktop

The cooktop should be connected to the gas supply by an

authorized installer. During installation of this product it is

essential to fit an approved gas tap to isolate the supply from

the appliance for the convenience of any subsequent removal

or servicing. Connection of the appliance to the gas mains

or liquid gas tanks must be carried out according to the safety

standards currently in force, and only after it is ascertained

that it is suitable for the type of gas to be used. If not, follow

the instructions indicated in the section entitled, “Adapting

the Cooktop for Different Types of Gas”. If the cooktop is to

be connected to tanks containing liquid gas, use pressure

regulators that comply with current safety standards.

Important: To insure that the appliance operates safety, the

gas is regulated correctly and your appliance lasts over time,

make sure that gas pressure levels comply with the

indications given in Table 1, “Nozzle and Burner

Specifications”.

Gas Connection to Non-flexible Pipe

(copper or steel)

Connection to the gas source must be done in such a way

as to not create any stress points at any part of the appliance.

The appliance is fitted with an adjustable, "L" shaped

connector and a gasket for the attachment to the gas supply.

Should this connector have to be turned, the gasket must be

replaced (supplied with the appliance).

The gas feed connector to the appliance is a threaded, male

1/2" connector for round gas pipe.

Gas Connection to Flexible Steel Pipe

The gas feed connector to the appliance is a threaded, male

1/2" connector for round gas pipe. Only use pipes, tubes

and gaskets that comply with current safety codes. The

maximum length of the flexible pipes must not exceed 2000

mm. Once the connection has been made, ensure that the

flexible metal tube does not touch any moving parts and is

not crushed.

16

Check the Seal

Once the appliance has been installed, make sure all the

connections are properly sealed, using a soapy water

solution. Never use a flame.

Electrical Connection

The cooktops fitted with a tripolar electrical supply cord are

designed to be be used with alternating current according to

the indications on the rating plate located under the cooktop.

The earthing wire can be identified by its yellow-green colour.

In the case of installation over a built-in electric oven, the

electrical connections for the cooktop and oven should be

independent, not only for safety purposes, but also to

facilitate removal of one or both in the future.

Electrical Connection for Gas Cooktop

Fit the supply cord with a standard plug for the demand rate

indicated on the rating plate or connect it directly to the

electrical mains. In the latter case, a single pole switch must

be placed between the appliance and the mains, with a

minimum opening between the contacts of 3 mm in

compliance with current safety codes (the earthing wire must

not be interrupted by the switch). The power supply cord

must be positioned so that it does not reach a temperature

in excess of 50°C above room temperature at any point.

Before making the actual connection, make sure that:

• The fuse and electrical system can withstand the load

required by the appliance;

• That the electrical supply system is equiped with an

efficient earth hook-up according to the norms and

regulations prescribed by law;

• That the plug or switch is easily accessible.

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow - Earth

Blue - Neutral

Brown - Live

As the colours of the wires in the mains lead may not

correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

Connect the Green & Yellow wire to the terminal marked “E”

or or coloured Green or Green & Yellow.

Connect the Brown wire to the terminal marked “L” or coloured

Red.

Connect the Blue wire to the terminal marked “N” or coloured

Black.

Adapting the Cooktop for Different Types of Gas

To adapt the cooktop to a different type of gas than that for

which it was designed, (see the sticker under the hob or on

the packaging), the burner nozzles must be changed, as

follows:

• Remove the pan supports and slide the burners out of

the cooktop.

• Unscrew the nozzles using a 7mm socket wrench and

replace them with those for the new type of gas. (See

table 1, “Burner and Nozzle Specifications”).

• Reassemble the parts following the instructions in reverse

order.

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

If the gas pressure is different than that prescribed, a pressure

regulator must be installed at the source, in compliance with

national standards governing the use of piped gas regulators.

Regulation of Air Supply to the Burner

The burners do not need a primary air regulator.

Minimum Regulation

• Turn the gas valve to minimum.

• Remove the knob and turn the regulator screw (positioned

either on the side of the top or inside the shaft) clockwise

until the flame becomes small but regular.

N.B.: In the case of liquid gas, the regulation screw must be

fully screwed in (clockwise).

• Make sure that, when the knob is turned rapidly high to

low, the flame does not go out.

• In the event of a malfunction on appliances with the

security device (thermocouple) when the gas supply is

set at minimum, increase the minimum supply levels using

the regulator screw.

Once the adjustment has been made, apply sealing wax, or

a suitable substitute, to the old seals on the by-pass.

17

Table 1

Liquid Gas Natural Gas

Burner Diameter

(mm)

Thermal power

kW (p.c.s.*)

By-Pass

1/100

Nozzle

1/100

Flow*

g/h

Nozzle

1/100

Flow*

l/h

Nomin. Ridot. (mm) (mm) *** ** (mm)

Fast (R) 100 3,00 0,70 41 87 218 214 128 286

Semi Fast (S) 75 1,90 0,40 30 70 138 136 104 181

Auxiliary (A) 51 1,00 0,40 30 52 73 71 76 95

Triple Crown (TC) 100 2,50 0,80 48 83 182 179 124 238

Supply

Pressures

Nominal (mbar)

Minimum (mbar)

Maximum (mbar)

28-30

20

35

37

25

45

20

17

25

* At 15°C and 1013 mbar-dry gas

** Propane P.C.S. = 50.37 MJ/kg.

*** Butane P.C.S. = 49.47 MJ/kg.

Natural P.C.S. = 37.78 MJ/m

3

This appliance conforms with the following European

Economic Community directives:

- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent

modifications;

- 89/336/EEC of 03/05/89 (Electromagnetic Compatibility)

and subsequent modifications;

- 90/396/EEC of 29/06/90 (Gas) and subsequent

modifications;

- 93/68/EEC of 22/07/93 and subsequent modifications.

The European Directive 2002/96/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed of

in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to optimise

the recovery and recycling of the materials they contain

and reduce the impact on human health and the

environment. The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when you di-

spose of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their old

appliance.

Characteristic of the burners and nozzles

S S

R A

SS

RA

S

R A

S

RA

PF 64 PF 631 E

PF 640 E PF 631 ES

PF 640 ES PF 631 P

PF 640 P PF 640 ES R

SSAAA

TCTC RRR

PF 640 EST

Page is loading ...

Ariston PF 631 E (WH) Owner's manual

Ariston PF 631 E (WH) Owner's manual

in other languages

Related papers