Ditel Digital Stars 8000TP Technical Manual

Brand
Ditel
Model
Digital Stars 8000TP
Type
Technical Manual

Ditel Digital Stars 8000TP is a high-precision digital strain meter designed for use with bridge type transducers. It offers a wide range of features and capabilities, making it an ideal choice for a variety of applications, including:

  • Strain measurement: The 8000TP can be used to measure strain in a variety of materials, including metals, plastics, and composites. It is ideal for applications such as structural testing, fatigue analysis, and materials characterization.

  • Load measurement: The 8000TP can also be used to measure load in a variety of applications, such as weighing systems, force measurement, and torque measurement.

Ditel Digital Stars 8000TP is a high-precision digital strain meter designed for use with bridge type transducers. It offers a wide range of features and capabilities, making it an ideal choice for a variety of applications, including:

  • Strain measurement: The 8000TP can be used to measure strain in a variety of materials, including metals, plastics, and composites. It is ideal for applications such as structural testing, fatigue analysis, and materials characterization.

  • Load measurement: The 8000TP can also be used to measure load in a variety of applications, such as weighing systems, force measurement, and torque measurement.

Print this page
DITEL: PRODUCTS: DIGITAL STARS: 8000TP
INPUT SENSIVITY
Strain meters for brid
g
e type transducers are confi
g
ured for an input sensivity
(transducer output in mV) of 100mV at full-scale.
To modifie this value, replace the resistor R6 for one whose value is given by
the following formulas:
where: mV = cell sensivity (in mV) for the constant current that supplies the
meter (1.5mA).
If the transducer's specifications are given for an excitation current different
from 1.5mA, apply the proportional factor to obtain the mV output at a
current of 1.5mA.
DISPLAY READING
After configuring the input sensivity, apply the following formula to determine
the value of R18 in order to get the desired display readout (VD).
R18)ohm) = ((553*(2500 - VD)) / VD) - 100
With the resistance value obtained from the formula, the span adjustment
margin is set to 20% of the display readout VD.
COMMON MODE REJECTION RATIO
Tie terminals B and C togheter at the input connector and connect two
resistors of 1Mohm from this point to pin A and pin D as it is indicated in the
figure at right.
Adjust the ZERO potentiometer until 0V are obtained between its middle point
(slider) and the meter ground (taken at the point -M- of the capacitor).
Adjust finally the RP3 potentiometer until the display registers 0V.
DISPLAY RANGE ADJUSTMENT
Connect two resistors of 1kohm between the input C and pins A and D in
order to reference this input to the tranducer's excitation.
N = 2750 / mV R6(ohm) = 12000 / N - 3
P
á
g
ina 1 de 2www.ditel.es
|
Products
|
Di
g
ital Stars Series
|
8000TP
05/09/2005file://F:\ditelweb\a
p
aratos\e8000t
p
.htm
Change language | Back to the menu
Connect between pins B and C an accurate reference millivoltmeter replacing
the full-scale transducer's signal and adjust the SPAN potentiometer until the
display reads the desired value.
Shortcircuit pins B and C and readjust 0V with the ZERO potentiometer.
Warranty:
Press the icon to see it.
P
á
g
ina 2 de 2www.ditel.es
|
Products
|
Di
g
ital Stars Series
|
8000TP
05/09/2005file://F:\ditelweb\a
p
aratos\e8000t
p
.htm
  • Page 1 1
  • Page 2 2

Ditel Digital Stars 8000TP Technical Manual

Brand
Ditel
Model
Digital Stars 8000TP
Type
Technical Manual

Ditel Digital Stars 8000TP is a high-precision digital strain meter designed for use with bridge type transducers. It offers a wide range of features and capabilities, making it an ideal choice for a variety of applications, including:

  • Strain measurement: The 8000TP can be used to measure strain in a variety of materials, including metals, plastics, and composites. It is ideal for applications such as structural testing, fatigue analysis, and materials characterization.

  • Load measurement: The 8000TP can also be used to measure load in a variety of applications, such as weighing systems, force measurement, and torque measurement.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents