Eurolux F4NW Owner's manual

Brand: Eurolux

Model: F4NW

Type: Owner's manual

This manual is also suitable for

5 Blade Ceiling Fan

F4W / B / NW / CHE / CSC

PRODUCT CODE

TROUBLE SHOOTING:

CAUTION: Ensure power supply is turned off before attempting trouble shooting.

NOTE: This fan does not contain servicable parts.

DO NOT OPEN or TAMPER WITH THE MOTOR.

Should your fan not start:

1) Check fuses are in place in the switchboard.

2) Recheck the terminal strip connections.

3) Ensure the wall & direction switches are not stuck in a “middle” position.

4) Ensure that the shipping tabs (gure 14) have been removed.

Should your fan be noisy:

1) Check all screws are sufciently tight: fan blades and fan holders, (if applicable) glass of

the lamp holder.

2) Allow at least 24 hours for the fan to settle.

Should your fan wobble:

In general, wobble is caused by the blades not cutting the air at the same point. Measure

downwards from the ceiling and make sure each blade is at the same height to the ceiling.

See Figure 1. If they are not, adjust by hand by slightly bending the blade and bracket.

If a major adjustment is needed, insert a washer as shown in Figure 2.

1) Check the blades are securely fastened to the holders.

2) Check the blade holders are tight on the motor.

3) Ensure the mounting bracket is properly screwed to the ceiling.

4) Interchange opposite blade sets if needed.

Should the light on your fan not work:

1) Check the terminal connections are tight.

2) Check if the lamp is blown.

Should the above fail, contact a qualied electrician for assistance.

Touching

Ceiling

Figure 1 Figure 2

Blade Brackets

Blade Tip Down:

Fan Blade

Blade Tip Down:

Fan Blade

Fan Wobbles:

Please read instructions before commencing installation and retain for

future reference.

Cape Town - 9 Racecourse Road, Milnerton, 7441

Johannesburg - 10 Milkyway Avenue, Linbro Business Park, Sandton, 2065

email: [email protected], web: www.eurolux.co.za

ENVIRONMENTAL PROTECTION

Waste electrical & Electronic equipment regulations requires that any of our products showing this

marking must not be disposed of with other household or commercial waste. To prevent possible

harm to the environment or human health from uncontrolled waste disposal, please separate any

such products from other waste types and recycle it responsibly at your local facilities.

Excluding: 2 x E14 Golfball Maximum 40W 230V

• The fan is operated by pull string:

First Pull: High Speed

Second Pull: Medium Speed

Third Pull: Low Speed

Fourth Pull: Off

• The slide switch operates the direction of the fan.

Down / Forward Position: Counter clockwise rotation for cooling.

Up / Reverse Position: Clockwise rotation for heating.

• Note: Before chaning the direction of the fan, turn fan off, and allow to come to a complete stop.

• Note: Fans move during operation which may cause some connections to come loose.

Check the supporting screws, brackets and blade attachements twice a year to ensure they

are secure.

F4W / B / NW / CHE / CSC - attachments:

If the external exible cable or cord of this luminaire is damaged, it should be exclusively replaced

by the manufacturer or his service agent or a similar qualied person in order to avoid a hazard.To

ensure that you get maximum longevity and maximum use out of your luminaire, please observe

the following safety instructions.

Electrical products can cause death, injury, or damage to property. Installation of the luminaire

must be carried out by a qualied electrician, in accordance with SANS 10142. On completion

of installation, ensure that the Certicate of Compliance is updated.

• Before connecting this fan, ensure that voltage indicated on the rating label corresponds

with the mains voltage in your home.

• When cleaning, ensure that the power is turned off.

• This fan is checked in full for conformity to the quality standards and safety requirements.

• The manufacturer / supplier is not responsible for any damage of properties and persons,

caused by the incorrect use or installation of the fan.

• Should you be unsure of how to install this fan correctly, please consult a professional

electrician or your supplier for assistance.

• Ensure all items/ components, threads and screws are tightly secured.

IMPORTANT:

• Tampering with this fan, I.E. Using silicon sealers or incorrect cabling, will invalidate your

warranty. If one is not supplied within the carton, DO NOT use a solid speed control.

• Each blade set supplied is weighted and a complete set. If installing more than one fan, DO NOT

mix or add blades as this can cause your fan to wobble.

• Please check whether the connection of the power cord is safe and reliable before installation.

• Always ensure that the mains supply voltage is correct.

• Do not use the fan outdoors, in wet conditions or areas of high humidity.

• Do not insert objects or ngers through the bars of the grill.

IMPORTANT SAFEGUARDS

OPERATION

CLEANING

• Before cleaning always ensure the power supply is turned off and that the fan has

been unplugged.

• Do not immerse the fan in water.

• No abrasive products, solvents, detergent may be used to clean this fan.

• Ensure that the fan does not come in contact with corrosive chemicals, etc.

• The motor bearings are permanently sealed and do not require additional lubrication.

•Fittingmaterial: Pressed steel with frosted glass lens

•Lamp: Excluding 2 x E14 Golfball Maximum 40W 230V

•Motor: 60W

•Voltage: 220 - 240V~ 50/60Hz.

•Protectionagainstelectricshock: Class 1. Requires earth connection

•IPRating: 20. Protected against solid foreign objects of 12.5mm Ø and greater, not protected

against water.

• Not for outdoor use or in wet conditions and areas of high humidity

•Dimensions: (H)355mm x (Ø)1320mm.

•Features: 3 Speed Forward and Reverse

•NumberofBlades:5 Blades

2 Pull String Switches

•SpareGlass:Code X159

• 2 Years warranty

SPECIFICATIONS

• This appliance is not intended for use by young children or inrm persons unless they have

been adequately supervised by a responsible person.

• Always unplug the fan when cleaning or moving from one location to another.

• Always ensure that the fan is on an even, stable surface.

• To disconnect the appliance, unplug by rst turning off the mains power then unplugging the

fan. Do NOT pull on the cord, always grasp the plug.

• This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for

their safety.

• Children should be supervised to ensure that they do not play with the appliance.

After fan is installed and hanging straight, tighten the

true-balance canopy bolts with pliers or wrench to

eliminate wobble during operation.

NOTE: Over-tightening bolts may damage canopy.

DOWNROD INSTALLATION ONLY

If plastic shipping stabilizer tabs are attached to motor,

remove and discard. Attach blade assembly to motor

housing using the noise dampening motor gasket and

motor screws provided. Tighten screws securely.

NOTE: Some models do not utilize motor gasket,

washer or stabilizer tabs.

ATTACHED SWITCH

HOUSING MODELS

DETACHED SWITCH

HOUSING MODELS

Washer

Noise-

dampening

Gasket

NOTE:

To Attach Switch

Housing, refer to

Light Kit

Installation Sheet

Shipping

Stabilizer

Tab

Attach blade brackets to blades by using the blade braket

screws and metal or fabric washers, if provided.

NOTE: Some models do not utilize fabric washer

or nuts.

ONE AND TWO PIECE BLADE BRACKET

ASSEMBLY

Fabric

Washers

Metal

Washers

Nuts

Wahers

Screws

16-1 16-2

Install the light kit to the fan base with the

screws supplied

16-4

Install the bulb being careful not to over-

tighten.

16-3

Install the acrylic ring as shown with the

two screws

17-1

Find the connector in the switch housing and connector

in the light kit. Slide both together.

17-3

17-2

Attach light kit to fan switch housing and secure tightly

from below with the screws provided. Add light bulbs

(not included)

10 Follow diagram above to connect wires.

Make sure that all exposed wiring is secured inside the

terminal block.

From Fan:

4 Pole

Connector

L - Block

N - Block

- Block

From House:

Power Supply

Neutral

Earth (Yellow/Green)

Carefully lift fan from mounting plate hook, making sure not to

break any wire connections. The canopy has 2 mating slots and 2

mating holes (see illustration). Position both slots in canopy

directly under and in line with 2 mounting plate screws and lock

washers. lift fan until mounting plate screws are seated in

bottom of slots in canopy. Rotate clockwise until both

mounting screws drop into slot recesses. Tighten screws

securely. Install third and fourth screwswith lockwasher

into mating holes and tighten.

Mounting Slots

Insert downrod and ball assembly into large opening in

canopy, making sure canopy tab engages notch in

downrod ball. Place true-balance clamp ring over down-

rod ball and install 3 true-balance bolts through the

bottom of the canopy and into clamp ring.

(These bolts will be tightened correctly in step #15).

Clamp Ring

Canopy Tab

Ball Notch

Insert downrod and ball assembly into large opening in

canopy, making sure canopy tab engages notch in

downrod ball. Place true-balance clamp ring over down-

rod ball and install 3 true-balance bolts through the

bottom of the canopy and into clamp ring.

(These bolts will be tightened correctly in step #15).

Locking Mechanism

Insert downrod into downrod yoke. Make sure to align

hole in downrod with the hole in downrod yoke.

Lift canopy and install yoke cross pin through yoke

downrod.

Insert clamp pin into cross pin until it snaps into place.

Tighten set screw in yoke.

Clamp

Cross

Pin Set Screws

NOTE: Flushmount option, downrod will not be used

INSTALLATION

Combo Motor:

Depending on Model purchased, this fan is capable of either 6/3 or 5/4 blade combinations.

Mounting Bracket

Slotted Hole

Round Hole

Flushmounted Installation

Ground Wire

Flushmounted Installation

Loosen set screw in downrod ball until ball moves easily up

and down the downrod. Do not remove ground wire from

downrod.

Slide downrod ball down, exposing cross pin. Do not remove

ball completely. Remove cross pin and save for later use.

5 6

Downrod Installation

Ground Wire

Downrod Ball

Cross Pin

Plug

Yoke

Motor Assembly

Eurolux F4NW Owner's manual

Brand: Eurolux

Model: F4NW

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Eurolux F4NW Owner's manual

This manual is also suitable for

Eurolux F4NW Owner's manual

Related papers

Other documents