Table of contents
6
BiG Pack 4x4 XC
Original operating instructions 150000758_06_us
13.11 Switching the working light on/off.............................................................................................160
13.12 Releasing/locking self-steering axle.........................................................................................160
13.13 Operating the starter aid ..........................................................................................................161
13.13.1 Switching on starter aid............................................................................................................161
13.13.2 Switching off starter aid............................................................................................................161
13.14 Opening/closing bale channel flaps .........................................................................................162
13.15 Lower the bale chute................................................................................................................162
13.16 Automatic bale ejection............................................................................................................162
13.17 Selecting "Counter/Detail counter" menu.................................................................................162
13.18 Selecting a menu Level............................................................................................................162
13.19 Operating the knotter ...............................................................................................................163
13.19.1 Trigger knotter..........................................................................................................................163
13.19.2 Reset bale length to zero .........................................................................................................163
13.20 Operating the blade cassette ...................................................................................................163
13.20.1 Lifting the blade cassette .........................................................................................................164
13.20.2 Lowering the blade cassette ....................................................................................................164
13.21 Setting the target bale channel flap pressure (manual mode) .................................................164
13.22 Setting target baling force (automatic mode) ...........................................................................165
13.23 Setting target bale length .........................................................................................................165
13.24 Operating machine via joystick ................................................................................................166
13.24.1 Auxiliary functions (AUX) .........................................................................................................166
13.24.2 Auxiliary configuration of a joystick ..........................................................................................166
14 Terminal – Menus...................................................................................................................168
14.1 Menu Structure ........................................................................................................................168
14.2 Recurrent icons........................................................................................................................170
14.3 Bring up menu level ................................................................................................................171
14.4 Selecting a menu .....................................................................................................................171
14.5 Changing value ........................................................................................................................172
14.6 Changing mode........................................................................................................................173
14.7 Menu 1 "Knotter" .....................................................................................................................174
14.7.1 Menu 1-1 "Correction value for bale length" ............................................................................174
14.7.2 Menu 1-2 "Knotter signal" ........................................................................................................175
14.7.3 Menu 1-3 "Knotter monitoring".................................................................................................176
14.7.4 Menu 1-4 “Blowing Interval Knotter Cleaning" .........................................................................177
14.7.5 Menu 1-5 "Duration of cleaning operation" ..............................................................................177
14.8 Menu 2 "Sensitivity of direction display"...................................................................................178
14.9 Menu 3 "Central lubrication".....................................................................................................179
14.10 Menu 4 "Weighing device" .......................................................................................................180
14.11 Menu 5 "Moisture measurement".............................................................................................182
14.11.1 Menu 5-1 “Error message for moisture measurement"............................................................182
14.11.2 Menu 5-2 "Correction value for moisture measurement" .........................................................183
14.11.3 Menu 5-3 "Select internal / external moisture measurement"..................................................184
14.12 Menu 6 "External silage additives unit"....................................................................................186
14.13 Menu 8 "Self-steering axle"......................................................................................................186
14.13.1 Setting the speed for blocking the self-steering axle ...............................................................187
14.14 Menu 13 "Counters".................................................................................................................188
14.14.1 Menu 13-1 "Customer counter"................................................................................................189
14.14.1.1 Detail counter...........................................................................................................................190
14.14.2 Menu 13-2 "Total counter" .......................................................................................................193
14.15 Menu 14 "ISOBUS"..................................................................................................................194
14.15.1 Menu 14-2 “Driving speed/direction of travel diagnostics” .......................................................195
14.15.2 Menu 14-3 "Configuring main window" ....................................................................................196
14.15.3 Menu 14-4 "Set background colour" ........................................................................................198
14.15.4 Menu 14-5 "KRONE SmartConnect"........................................................................................199
14.15.5 Menu 14-9 “Switching Between the Terminals” .......................................................................199
14.15.6 Menu 14-11 "Task Controller"..................................................................................................200
14.15.7 Menu 14-12 "Data Logger".......................................................................................................201
14.16 Menu 15 "Settings"...................................................................................................................201
14.16.1 Menu 15-1 “Sensor Test” .........................................................................................................202
14.16.2 Menu 15-2 "Actuator test" ........................................................................................................206
14.16.3 Menu 15-3 "Software info" .......................................................................................................210