Smeg SC106B-8 Datasheet

Brand: Smeg

Model: SC106B-8

Category: Ovens

Type: Datasheet

This manual is also suitable for

Contents

INSTRUCTIONS FOR THE USER: these contain user advice, description of

the commands and the correct procedures for cleaning and maintenance

of the appliance.

INSTRUCTIONS FOR THE INSTALLER: these instructions are intended for

the qualified technician who must perform the installation, put it into

operation and test the appliance.

1. INSTRUCTIONS FOR USE ......................................................................... 66

2. SAFETY PRECAUTIONS ............................................................................ 68

3. ENVIRONMENTAL RESPONSIBILITY ........................................................ 70

4. GET TO KNOW YOUR OVEN...................................................................... 71

5. AVAILABLE ACCESSORIES ....................................................................... 72

6. USING THE OVEN ...................................................................................... 79

7. COOKING WITH THE OVEN....................................................................... 95

8. CLEANING AND MAINTENANCE............................................................. 105

9. EXTRAORDINARY MAINTENANCE ......................................................... 117

10. INSTALLING THE APPLIANCE ................................................................. 123

General instructions

1. INSTRUCTIONS FOR USE

THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. IT MUST BE KEPT IN ITS

ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF

THE APPLIANCE.

CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN

BEFORE USING THE APPLIANCE IS ESSENTIAL. INSTALLATION MUST BE

CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE

REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE

AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE

APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS:

COOKING FOOD; ALL OTHER USES ARE CONSIDERED UNSUITABLE.

THE MANUFACTURER CANNOT BE HELD LIABLE FOR USE OTHER THAN AS

INDICATED.

IF THE APPLIANCE IS INSTALLED ON BOATS OR IN CARAVANS, DO NOT USE IT AS

A ROOM HEATER.

DO NOT USE THIS APPLIANCE FOR HEATING ROOMS.

THIS APPLIANCE IS MARKED ACCORDING TO EUROPEAN DIRECTIVE 2002/96/EC

ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE).

THIS GUIDELINE IS THE FRAME OF A EUROPEAN-WIDE VALIDITY OF RETURN

AND RECYCLING ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT.

NEVER OBSTRUCT THE OPENINGS AND SLITS PROVIDED FOR VENTILATION AND

HEAT DISPERSAL.

DO NOT LEAN OR SIT ON THE OPEN DOOR OF THE APPLIANCE.

THE IDENTIFICATION PLATE WITH THE TECHNICAL DATA, SERIAL NUMBER AND

BRAND NAME HAS BEEN VISIBLY AFFIXED TO THE APPLIANCE.

DO NOT REMOVE THIS PLATE FOR ANY REASON.

BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE PROTECTIVE FILMS

APPLIED INSIDE OR OUTSIDE MUST BE REMOVED.

TAKE CARE THAT NO OBJECTS ARE STUCK IN THE DOOR OF THE OVEN.

THE APPLIANCE BECOMES VERY HOT INSIDE DURING USE. SUITABLE HEAT-

PROOF GLOVES SHOULD BE WORN FOR ALL OPERATIONS.

General instructions

DO NOT USE STEEL SPONGES AND SHARP SCRAPERS AS THEY WILL

DAMAGE THE SURFACE.

USE NORMAL NON-ABRASIVE PRODUCTS, INCLUDING WOODEN OR

PLASTIC UTENSILS IF NECESSARY. RINSE THOROUGHLY AND DRY

USING A SOFT CLOTH OR A MICROFIBRE CLOTH.

DO NOT ALLOW RESIDUES OF SUGARY FOODS (SUCH AS JAM) TO SET

INSIDE THE OVEN. IF THEY ARE ALLOWED TO SET FOR TOO LONG,

THEY COULD RUIN THE ENAMEL COVERING THE INSIDE OF THE OVEN.

DO NOT USE PLASTIC KITCHENWARE OR CONTAINERS. THE HIGH

TEMPERATURES INSIDE THE OVEN COULD MELT THE PLASTIC, DAMAGING THE

APPLIANCE.

DO NOT USE SEALED TINS OR CONTAINERS IN THE APPLIANCE.

OVERPRESSURE MAY OCCUR INSIDE THE CONTAINERS DURING COOKING,

CREATING A DANGER OF EXPLOSION.

DO NOT LEAVE THE APPLIANCE UNATTENDED DURING COOKING PROCESSES

WHERE FATS OR OILS COULD BE RELEASED.

FATS AND OILS MAY CATCH FIRE.

DO NOT COVER THE BOTTOM OF THE OVEN WITH ALUMINIUM OR TINFOIL

SHEETS DURING COOKING AND DO NOT PLACE PANS OR TRAYS ON IT TO AVOID

DAMAGE TO THE ENAMELLED SURFACE.

IF THE SURFACES ARE STILL VERY HOT DURING COOKING, DO NOT POUR

WATER DIRECTLY ONTO THE TRAYS. THE STEAM COULD CAUSE SEVERE BURNS

AND DAMAGE TO ENAMELLED SURFACES.

ALL COOKING OPERATIONS MUST TAKE PLACE WITH THE DOOR CLOSED.

General instructions

2. SAFETY PRECAUTIONS

REFER TO THE INSTALLATION INSTRUCTIONS FOR THE SAFETY REGULATIONS

FOR ELECTRIC OR GAS APPLIANCES AND VENTILATION FUNCTIONS.

IN YOUR INTERESTS AND FOR YOUR SAFETY IT HAS BEEN ESTABLISHED BY

LAW THAT THE INSTALLATION AND SERVICING OF ALL ELECTRICAL APPLIANCES

IS TO BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE

REGULATIONS IN FORCE.

OUR APPROVED INSTALLERS GUARANTEE A SATISFACTORY JOB.

GAS OR ELECTRICAL APPLIANCES MUST ALWAYS BE DISCONNECTED BY

SUITABLY SKILLED PEOPLE.

BEFORE CONNECTING THE APPLIANCE TO THE POWER GRID, CHECK THE DATA

ON THE PLATE AGAINST THE DATA FOR THE GRID ITSELF.

BEFORE CARRYING OUT INSTALLATION / MAINTENANCE WORK, MAKE SURE

THAT THE APPLIANCE IS NOT CONNECTED TO THE POWER GRID.

THE PLUG TO BE CONNECTED TO THE POWER SUPPLY CABLE AND ITS SOCKET

MUST BE OF THE SAME TYPE AND CONFORM TO THE REGULATIONS IN FORCE.

THE SOCKET MUST BE ACCESSIBLE AFTER THE APPLIANCE HAS BEEN BUILT-IN.

NEVER DISCONNECT THE PLUG BY PULLING ON THE CABLE.

IF THE POWER SUPPLY CABLE IS DAMAGED, CONTACT THE TECHNICAL

SUPPORT SERVICE IMMEDIATELY AND THEY WILL REPLACE IT.

IT IS OBLIGATORY FOR ALL ELECTRICAL EQUIPMENT TO BE EARTHED

ACCORDING TO THE METHODS LAID DOWN BY SAFETY REGULATIONS.

IMMEDIATELY AFTER INSTALLATION CARRY OUT A BRIEF INSPECTION TEST,

FOLLOWING THE INSTRUCTIONS BELOW. SHOULD THE APPLIANCE NOT

FUNCTION, DISCONNECT IT FROM THE ELECTRICITY SUPPLY AND CALL THE

NEAREST TECHNICAL SUPPORT CENTRE.

NEVER ATTEMPT TO REPAIR THE APPLIANCE.

NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: IF IT IS SWITCHED ON BY

ACCIDENT, IT MAY CAUSE A FIRE.

DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH

THE HEATING ELEMENTS INSIDE THE OVEN.

THIS APPLIANCE MAY NOT BE USED BY PEOPLE (INCLUDING CHILDREN) OF

REDUCED PHYSICAL AND MENTAL CAPACITY, OR LACKING IN EXPERIENCE IN

THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR

INSTRUCTED BY ADULTS RESPONSIBLE FOR THEIR SAFETY.

General instructions

DO NOT LET CHILDREN GO NEAR THE APPLIANCE WHEN IT IS IN OPERATION OR

PLAY WITH IT AT ANY TIME.

DO NOT INSERT POINTED METAL OBJECTS (CUTLERY OR UTENSILS) INTO THE

SLITS IN THE APPLIANCE.

DO NOT USE STEAM JETS FOR CLEANING THE APPLIANCE.

THE STEAM COULD REACH THE ELECTRONICS, DAMAGING THEM AND CAUSING

SHORT-CIRCUITS.

DO NOT MODIFY THIS APPLIANCE.

DO NOT SPRAY ANY SPRAY PRODUCTS NEAR THE ELECTRICAL APPLIANCE

WHILE IT IS IN OPERATION.

DO NOT USE SPRAY PRODUCTS WHILE THE PRODUCT IS STILL HOT.

The manufacturer declines all responsibility for damage to persons or things caused

by the non-observance of the above prescriptions or deriving from tampering with

any part of the appliance or by the use of non-original spares.

Instructions for disposal

3. ENVIRONMENTAL RESPONSIBILITY

Our product's packing is made of non-polluting materials, therefore compatible

with the environment and recyclable. Please help by disposing of the packing

correctly. You can obtain the addresses of collection, recycling and disposal

centres from your retailer or from the competent local organisations.

Do not discard the packaging or any part of it, or leave it unattended. It

can constitute a suffocation hazard for children, especially the plastic

bags.

Your old appliance also needs to be disposed of correctly.

Important: hand over your appliance to the local agency authorised for the

collection of electrical appliances no longer in use. Correct disposal enables

intelligent recovery of valuable materials.

Before disposing of your appliance it is important to remove doors and leave

shelves in the same position as for use, to ensure that children cannot

accidentally become trapped inside during play. It is also necessary to cut the

connecting cable to the power grid, removing it along with the plug.

Instructions for the user

4. GET TO KNOW YOUR OVEN

Control panel

Roof liner

Inside lights

Rack and tray support

frames (on some

models only)

Insert for the rotisserie

rod (on some models

only)

Bottom plate (on some

models only)

Multifunction Model

Pizza plate or cover recess

(on some models only)

Oven fan

Pyrolytic Model

Instructions for the user

5. AVAILABLE ACCESSORIES

NOTE:

Some models are not provided with all

accessories.

Rack: for holding cooking containers.

Tray rack: to be placed over the top of the

oven tray; for cooking foods which may drip.

Oven tray: for collecting fat from foods placed

on the rack above.

Deep oven tray: for baking cakes, pizza and

oven desserts.

Handle: for removing hot racks and pans.

Pizza plate: specially designed for cooking

pizza and similar dishes.

Instructions for the user

Pizza spatula: for easy placement of the pizza

on the pizza plate.

Pizza plate cover: for covering the pizza plate

when it is not in use.

Rotisserie frame: supports the rotisserie rod.

Rotisserie rod: for cooking chicken and all

foods which require uniform cooking over their

entire surface.

• Accessories available on request:

Original supplied and optional accessories may be ordered from any

Authorised Support Centre.

• Use original SMEG accessories only.

Instructions for the user

5.1 Using the rack or tray

The racks and trays are equipped with a mechanical safety lock which prevents

them from being taken out accidentally. To insert the rack or tray correctly,

check that the lock is facing downwards (as shown in the figure at the side).

To remove the rack or tray, lift the front slightly.

The mechanical lock must always face the back of the oven.

Ovens with frames

Ovens with runners

Insert racks and trays fully into the oven until they come to a stop.

5.2 Using the support rack

The support rack is inserted into the tray

(as shown in the figure).

Using this, foods can be cooked and the

fat can be collected separately from the

food which is being cooked.

Instructions for the user

5.3 Use of the handles

The handles are used to extract hot trays

and racks from the oven.

Use the accessories as shown in the

figures at the side.

5.4 Using the rotisserie rod (on some models only)

When cooking with the rotisserie,

position the frame on the third runner

(see 6.2.1 Oven runners). Once the

frame is inserted, the shaped part

must sit facing outwards (as shown

in the figure).

Then prepare the rotisserie rod with

the food, using the clip forks

provided.

So that you can handle the rod with

the food on it readily, screw on the

handle provided.

Ovens with runners

Instructions for the user

Having prepared the rotisserie rod

with the food, position it on the guide

frame as shown in the figure.

Insert the rod into the hole (detail B)

so that it connects with the rotisserie

motor.

Make sure that the pin is placed

correctly on the guide frame (detail

A).

Ovens with runners

Instructions for the user

5.5 Using the pizza plate (on some models only)

With the oven cold, remove the circular cover from the bottom (as shown in the

figure) and insert the pizza plate.

Make sure that the plate is inserted correctly in the recess provided.

For cooking use the special pizza function .

Ovens with frames

Ovens with runners

Do not use the pizza plate other than as described, for example do not use it on

gas or glass-ceramic hobs or in ovens which are not designed for this purpose.

If you wish to add oil to your pizza, it is best to add it after removing it from the

oven since oil stains on the pizza plate are unsightly and may reduce its

efficiency.

In models where it is provided, if the pizza plate is not in use, cover the bottom

of the oven with the cover provided.

Instructions for the user

5.6 Using the pizza spatula (on some models only)

Always grip the pizza spatula on the wooden handle to put food in and take it out

of the oven.

You are advised to dust the steel surface lightly with flour to make it easier to

slide fresh products on and off, as they could stick to the steel due to their

moisture content.

Ovens with frames

Ovens with runners

Instructions for the user

6. USING THE OVEN

6.1 Before using the appliance

• Remove any labels (apart from the technical data plate) from trays, dripping

pans and the cooking compartment.

• Remove any protective film from the outside or inside of the appliance,

including from accessories such as trays, dripping pans, the pizza plate or

the base cover.

• Before using the appliance for the first time, remove all accessories from the

oven compartment and wash them as indicated in “8. CLEANING AND

MAINTENANCE”.

Heat the empty appliance to the maximum temperature in order to remove

any manufacturing residues which could affect the food with unpleasant odours.

6.2 General Description

6.2.1 Oven runners

The oven features 4 runners for positioning trays and racks at different heights.

The insertion heights are numbered from the bottom upwards (see figure).

Ovens with frames

Ovens with runners

Instructions for the user

6.2.2 Cooling system

The appliance is equipped with a cooling system

which comes into operation as soon as a cooking

function starts. The fan causes a steady outflow of

air from above the door which may continue for a

brief period of time even after the oven has been

turned off.

6.2.3 Oven inside lights

The oven lights come on when the door is opened

(only on some models) or any function or recipe is

selected, except for , and (where

present).

Instructions for the user

6.3 Warnings and general advice for usage

All cooking operations must be carried out with the door closed.

During cooking, do not cover the bottom of the oven with aluminium or tin foil

and do not place pans or oven trays on it as this may damage the enamel

coating. If you wish to use greaseproof paper, place it so that it will not interfere

with the hot air circulation inside the oven.

For the best cooking results, we recommend

placing cookware in the centre of the rack.

To prevent any steam in the oven from causing

problems, open the door in two stages: half

open (5 cm approx.) for 4-5 seconds and then

fully open. If you need to access the food,

always leave the door open for as short a time

as possible to prevent the temperature in the

oven from falling and ruining the food.

To prevent excessive amounts of condensation from forming on the internal

glass, hot food should not be left inside the oven for too long after cooking.

Instructions for the user

6.4 Description of the controls on the front panel

All the appliance's control and monitoring devices are located together on the

front panel.

Temperature selection knob Function selection

knob

This knob can be used to: set the

clock, select a temperature and the

cooking time, and set programmed

cooking.

(Temperature knob)

This knob can be used to select a

function or to switch off the oven.

(Function selection knob)

Multifunction

Model 109

Pyrolytic Model

109

Pyrolytic Model

108

Multifunction

Model 106

Pizza Model 106

Instructions for the user

The display shows the current time and,

during programmed cooking, it shows the

remaining cooking time or the completion

time.

During cooking, it shows the cooking

temperature set for the selected function.

Multifunction model

Pyrolytic Model

If the symbols to the side of the display are lit up, it means:

If flashing, it indicates that the time is being set; if steady it shows the

normal display (on multifunction models only).

Indicates that the door lock is activated during the automatic cleaning

phase (on pyrolytic models only).

Timer countdown activated.

Delayed-start timed cooking activated.

Child lock function ON (see 6.10 Secondary menu).

Timed cooking activated.

Instructions for the user

6.5 Operating modes

This appliance is designed to have two operating modes.

STAND-BY condition: this condition is set when the

function selection knob is positioned on the “0” symbol.

The appliance displays the current time.

ON condition: this condition is set when the function

selection knob is turned to any function and the

selected temperature appears on the display, or the

message “PYRO” if in pyrolysis.

6.6 First use

On the first use, or after a power failure, will be flashing on the oven's

display. To be able to start any cooking function, the current time must be set.

Turn the temperature selection knob right or left to

reduce or increase the displayed time.

Keep it in the turned position to reduce or increase

more rapidly.

(Temperature knob)

A few seconds after the last adjustment is made, the

time display will steady and the colon separating the

hours from the minutes will flash to indicate the start

of the countdown.

It may be necessary to alter the current time, for example due to daylight saving

hours; if so, hold the temperature selection knob turned to the right or left until

the value changes.

Page is loading ...

Smeg SC106B-8 Datasheet

Brand: Smeg

Model: SC106B-8

Category: Ovens

Type: Datasheet

This manual is also suitable for

Download PDF

report

Smeg SC106B-8 Datasheet

This manual is also suitable for

Smeg SC106B-8 Datasheet

Related papers

Other documents