Vizio VW42L - 42 Inch LCD HDTV User manual

Brand: Vizio

Model: VW42L - 42 Inch LCD HDTV

Category: TVs & monitors

Type: User manual

This manual is also suitable for

VW42L FHDTV10A LPL

Service Manual

V, Inc

320A Kalmus Drive Costa Mesa, CA 92626

TEL : +714-668-0588 FAX :+714-668-9099

Top Confidential

Model #: VIZIO VW42L

FHDTV10A_LPL/AUO

VIZIO VW42L FHDTV10A_LPL/AUO Service Manual

Table of Contents

CONTENTS PAGE

Sections

1. Features 1-1

2. Specifications 2-1

3. On Screen Display 3-1

4. Factory Preset Timings

4-1

5. Pin Assignment

5-1

6. Main Board I/O Connections 6-1

7. Theory of Circuit Operation 7-1

8. Waveforms 8-1

9. Trouble Shooting 9-1

10. Block Diagram 10-1

11. Spare parts list 11-1

12. Complete Parts List 12-1

Appendix

1. Main Board Circuit Diagram

2. Main Board PCB Layout

3. Assembly Explosion Drawing

Block Diagram

VINC Service Manual

VIZIO VW42L FHDTV10A_LPL/AUO

VIZIO VW42L FHDTV10A_LPL/AUO Service Manual

IBM and IBM products are registered trademarks of International Business Machines Corporation.

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

VINC and VINC products are registered trademarks of V, Inc.

VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards

Association (VESA).

Energy Star is a registered trademark of the US Environmental Protection Agency (EPA).

No part of this document may be copied, reproduced or transmitted by any means for any purpose

without prior written permission from VINC.

FCC INFORMATION

This equipment has been tested and found to comply with the limits of a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy, and if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment does cause unacceptable

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures -- reorient or relocate the receiving antenna; increase the separation between

equipment and receiver; or connect the into an outlet on a circuit different from that to which the

receiver is connected.

FCC WARNING

To assure continued FCC compliance, the user must use a grounded power supply cord and the

provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes

or modifications to Amtrak products will void the user’s authority to operate this device. Thus VINC

Will not be held responsible for the product and its safety.

CE CERTIFICATION

This device complies with the requirements of the EEC directive 89/336/EEC with regard to

“Electromagnetic compatibility.”

SAFETY CAUTION

Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);

Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric

Appliance Control Act); or an AC cord that meets the local safety standards.

CONFIDENTIAL – DO NOT COPY

Page 1-1

File No. SG-0264

Chapter 1 Features

1. Built in TV channel selector for TV viewing

2. Simultaneous display of PC and TV images

3. Connectable to PC’s analog RGB port

4. Built in HDTV, composite video, S-Video ,HDMI ,ATV out and DTV

out ,Audio line out, Audio optical out

5. Built in auto adjust function for automatic adjument of screen display

6. Smoothing function enables display of smooth texts and graphics even if

image with resolution lower than 1920x1080 is magnified

7. Power saving to reduce consumption power too less than 3W

8. On Screen Display: user can define display mode (i.e. color, brightness,

contrast, sharpness, backlight), sound setting, TV channel program,

aspect and gamma or reset all setting.

CONFIDENTIAL – DO NOT COPY

Page 2-1

File No. SG-0264

Chapter 2 Specification

1. TFT LCD CHARACTERISTICS

42.0”WUXGA TFT LCD

Item Specification

Active Screen Size 42 inch diagonal

Outline Dimension 983.0(H) x 576.0 (V) x 51.0 mm(D) (Typ.)

Pixel Pitch 0.4845 mm

Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement

Color Depth 8-bit, 16.7 M colors

Luminance, White 500 cd/m2 (Center 1point ,Typ.)

Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Typ.), U/D 178 (Typ.))

Power Consumption Total 320W (MAX.)

Weight 11.5 Kg (Typ.)

Display Mode Transmissive mode, Normally black

Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer

2.Input Connectors

Service port (USB) , HDMIX3, RCA (DVI Audio IN),D-SUB15PIN (MINI, 3rows),

RCAX2 (Component), RCAX2 (Audio IN) , RCAX1 (Audio IN), RCA (Composite) ,

S-Video (Composite), Tuner

3.Output Connectors

SPDIF Out (Optical Audio) , RCA (Audio OUT)

4. Power Supply

Power Consumption: 250W MAX

Power OFF: to less than 0.6W MAX

5.Speaker

Output 6Ω/10W (max) X2

6. ENVIRONMENT

Operating Temperature: 5c~35c (Ambient)

Operating Humidity: Ta= 35 °C, 90%RH (Non-condensing)

Operating Altitude: 0 - 14,000 feet (Non-Operating)

CONFIDENTIAL – DO NOT COPY

Page 2-2

File No. SG-0264

7. Dimensions (Physical dimension)

With Base Without Base

a. Height 722mm 694mm

b. Width 1028mm 1028mm

c. Depth 245mm 99.0mm

8. Weight (Physical weight)

a. Net 21.8 kgs

b. Gross 27.6 kgs

9. Precautions

Please pay attention to the followings when you use this TFT LCDmodule.

9-1. Mounting Precautions

(1) You must mount a module using holes arranged in four cornersor four sides.

(2) You should consider the mounting structure so that uneven force (ex. Twisted

stress) is not applied to the module. And the case on which a module is

mounted should have sufficient strength so that external force is not

transmitted directly to the module.

(3) Please attach the surface transparent protective plate to the surface in order to

protect the polarizer. Transparent protective plate should have sufficient

strength in order to the resist external force.

(4) You should adopt radiation structure to satisfy the temperature specification.

(5) Acetic acid type and chlorine type materials for the cover case are not

desirable because the former generates corrosive gas of attacking the

polarizer at high temperature and the latter causes circuit break by

electro-chemical reaction.

(6) Do not touch, push or rub the exposed polarizers with glass,tweezers or

anything harder than HB pencil lead. And please do not rub with dust clothes

with chemical treatment. Do not touch the surface of polarizer for bare hand or

greasy cloth.(Some cosmetics are detrimental to the polarizer.)

(7) When the surface becomes dusty, please wipe gently with absorbent cotton or

other soft materials like chamois soaks with petroleum benzine.

CONFIDENTIAL – DO NOT COPY

Page 2-3

File No. SG-0264

(8) Normal-hexane is recommended for cleaning the adhesives used to attach

front / rear polarizers. Do not use acetone, toluene and alcohol because they

cause chemical damage to the polarizer.

(9) Wipe off saliva or water drops as soon as possible. Their long time contact

with polarizer causes deformations and color fading.

(10) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than

following voltage: V=±200mV(Over and under shoot voltage)

(2) Response time depends on the temperature.(In lower temperature, it becomes

longer.)

(3) Brightness depends on the temperature. (In lower temperature, it becomes

lower.) And in lower temperature, response time(required time that brightness

is stable after turned on) becomes longer.

(4) Be careful for condensation at sudden temperature change. Condensation

makes damage to polarizer or electrical contacted parts. And after fading

condensation, smearor spot will occur.

(5) When fixed patterns are displayed for a long time, remnant image is likely to

occur.

(6) Module has high frequency circuits. Sufficient suppression to the

electromagnetic interference shall be done by system manufacturers.

Grounding and shielding methods may be important to minimized the

interference.

(7) Please do not give any mechanical and/or acoustical impact to LCM.

Otherwise, LCM can’t be operated its full characteristics perfectly.

(8) A screw which is fastened up the steels should be a machine screw. (if not, it

causes metallic foreign material and deal LCM afatal blow)

(9) Please do not set LCD on its edge.

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic

discharge. Make certain that treatment persons are connected to ground through

wrist band etc. And don’t touch interface pin directly.

CONFIDENTIAL – DO NOT COPY

Page 2-4

File No. SG-0264

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage

When storing modules as spares for a long time, the following precautions are

necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or

fluorescent light. Keep the temperature between 5°C and 35°C at normal

humidity.

(2) The polarizer surface should not come in contact with any other object. It is

recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape. When

the protection film is peeled off, static electricity is generated between the film

and polarizer. This should be peeled off slowly and carefully by people who

are electrically grounded and with well ion- blown equipment or in such a

condition, etc.

(2) When the module with protection film attached is stored for a long time,

sometimes there remains a very small amount of glue still on the bezel after

the protection film is peeled off.

(3) You can remove the glue easily. When the glue remains on thebezel surface

or its vestige is recognized, please wipe them off with absorbent cotton waste

or other soft material like chamois soaked with normal- hexane.

CONFIDENTIAL – DO NOT COPY

Page 3-1

File No. SG-0264

Chapter 3 On Screen Display

Main unit button

Power

CH ▲

CH ▼

VOL +

VOL -

Input

On Screen Display

TV Source

A. Picture：

a. Picture Mode (Custom/ Standard / Movie / Game)

b. Backlight (0~100)

c. Brightness (0~100)

d. Contrast (0~100)

e. Color (0~100)

f. Tint (-32~32)

g. Sharpness (0~7)

h. Color Temperature (Custom/Cool/Normal/Warm)

h-1. Custom： Red (0~255)

Green (0~255)

Blue (0~255)

i. Advanced Video

i-1. DNR(Off/Low/Medium/Strong)

i-2. Black Level Extender (On/Off)

i-3. White Peak Limiter (On/Off)

i-4 CTI(Off/Low/Medium/Strong)

i-5 Flesh Tone (On/Off)

i-6 Adaptive Luma (On/Off)

CONFIDENTIAL – DO NOT COPY

Page 3-2

File No. SG-0264

B. Audio：

a. Volume (0~100)

b. Bass (0~100)

c. Treble (0~100)

d. Balance (-50~50)

e. Surround (On/Off)

f. Digital Audio Out (Off/Dolby Digital/PCM)

g. Speakers (On/Off)

h. Lip Sync (0~5)

C. TV：

a. Tuner Mode (Antenna/Cable)

b. Auto Search

c. Skip Channel (Cable 1~135 / Antenna 2~69)

d. MTS (Stereo/SAP/Mono)

e. Time Zone (Hawaii/Eastern/Indiana/Central/Mountain/Arizona/Pacific/Alaska)

f. Daylight Saving (On/Off)

D. Setup：

a. Language (English/Francais/Espanol)

b. Sleep Timer (Off/30 Minutes/60 Minutes /90 Minutes /120 Minutes)

c. Wide (Wide/Zoom/Panoramic/Normal)

d. Input Naming (AV/Comp1/Comp2/RGB/HDMI1/ HDMI2/ HDMI3)

e. CC (Off/CC1/ CC2/ CC3/ CC4)

f. CC On Mute (Off/On)

g. Digital CC Style

g-1. Caption Style (Custom/As Broadcaster) Custom：

g-2. Font Size (Large/Small/Medium)

g-3. Font Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-4. Font Opacity (Translucent/solid/Transparent)

g-5. Background Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-6. Background Opacity (Translucent/solid/Transparent)

g-7. Window Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-8. Window Opacity (Translucent/solid/Transparent)

CONFIDENTIAL – DO NOT COPY

Page 3-3

File No. SG-0264

h. H/V Position

h-2. V.Position (0~32)

h-3. H.Size (0~100)

h-4. V.Size (0~100)

i. Reset All Setting

E. Parental：

a. PASSWORD

RGB Mode

A. Picture：

a. Auto Adjust (Run)

b. Backlight (0~100)

c. Brightness (0~100)

d. Contrast (0~100)

e. Color Temperature(Custom/6500/9300)

e-1. Custom： Red (0~255)

Green (0~255)

Blue (0~255)

f. H-size (0~255)

g. H-Position (0~100)

h. V-Position (0~100)

i. Fine Tune (0~31)

B. Audio：

a. Volume (0~100)

b. Bass (0~100)

c. Treble (0~100)

d. Balance (-50~50)

e. Surround (On/Off)

f. Digital Audio Out (Off/Dolby Digital/PCM)

g. Speakers (On/Off)

h. Lip Sync (0~5)

CONFIDENTIAL – DO NOT COPY

Page 3-4

File No. SG-0264

C. Setup：

a. Language (English/Francais/Espanol)

b. Sleep Timer (Off/30 Minutes/60 Minutes /90 Minutes /120 Minutes)

c. Wide (Wide/Zoom/Panoramic/Normal)

d. Input Naming (AV/Comp1/Comp2/RGB/HDMI1/ HDMI2/ HDMI3)

e. Reset All Setting

HDMI MODE

A. Picture：

a. Picture Mode (Custom/ Standard / Movie / Game)

b. Backlight (0~100)

c. Brightness (0~100)

d. Contrast (0~100)

e. Color (0~100)

f. Tint (-32~32)

g. Sharpness (0~7)

h. Color Temperature (Custom/Cool/Normal/Warm)

h-1. Custom：Red (0~255)

Green (0~255)

Blue (0~255)

i. Advanced Video

i-1. DNR(Off/Low/Medium/Strong)

i-2. Black Level Extender (On/Off)

i-3. White Peak Limiter (On/Off)

i-4 CTI(Off/Low/Medium/Strong)

i-5 Flesh Tone (On/Off)

i-6 Adaptive Luma (On/Off)

B. Audio：

a. Volume (0~100)

b. Bass (0~100)

c. Treble (0~100)

d. Balance (-50~50)

e. Surround (On/Off)

f. Digital Audio Out (Off/Dolby Digital/PCM)

CONFIDENTIAL – DO NOT COPY

Page 3-5

File No. SG-0264

g. Speakers (On/Off)

h. Lip Sync (0~5)

C. Setup：

a. Language (English/Francais/Espanol)

b. Sleep Timer (Off/30 Minutes/60 Minutes /90 Minutes /120 Minutes)

c. Wide (Wide/Zoom/Panoramic/Normal)

d. Input Naming (AV/Comp1/Comp2/RGB/HDMI1/ HDMI2/ HDMI3)

e. H/V Position

e-1. H.Position (0~64)

e-2. V.Position (0~32)

e-3. H.Size (0~100)

e-4. V.Size (0~100)

f. Reset All Setting

Video Sources：

AV1、AV2、COMPONENT1、COMPONENT2

A. Picture：

a. Picture Mode (Custom/ Standard / Movie / Game)

b. Backlight (0~100)

c. Brightness (0~100)

d. Contrast (0~100)

e. Color (0~100)

f. Tint (-32~32)

g. Sharpness (0~100)

h. Color Temperature (Custom/Cool/Normal/Warm)

h-1. Custom： Red (0~255)

Green (0~255)

Blue (0~255)

i. Advanced Video

i-1. DNR(Off/Low/Medium/Strong)

i-2. Black Level Extender (On/Off)

i-3. White Peak Limiter (On/Off)

i-4 CTI(Off/Low/Medium/Strong)

CONFIDENTIAL – DO NOT COPY

Page 3-6

File No. SG-0264

i-5 Flesh Tone (On/Off)

i-6 Adaptive Luma (On/Off)

B. Audio：

a. Volume (0~100)

b. Bass (0~100)

c. Treble (0~100)

d. Balance (-50~50)

e. Surround (On/Off)

f. Digital Audio Out (Off/Dolby Digital/PCM)

g. Speakers (On/Off)

h. Lip Sync (0~5)

C. Setup：

a. Language (English/Francais/Espanol)

b. Sleep Timer (Off/30 Minutes/60 Minutes /90 Minutes /120 Minutes)

c. Wide (Wide/Zoom/Panoramic/Normal)

d. Input Naming (AV/Comp1/Comp2/RGB/HDMI1/ HDMI2/ HDMI3)

e. CC (Off/CC1/ CC2/ CC3/ CC4)

f. CC On Mute (Off/On)

g. Digital CC Style

g-1. Caption Style (Custom/As Broadcaster) Custom：

g-2. Font Size (Large/Small/Medium)

g-3. Font Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-4. Font Opacity (Translucent/solid/Transparent)

g-5. Background Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-6. Background Opacity (Translucent/solid/Transparent)

g-7. Window Color (white/Green/Blue/Red/Cyan/Yellow/Magenta/Black)

g-8. Window Opacity (Translucent/solid/Transparent)

h. H/V Position

h-1. H.Position (0~64)

h-2. V.Position (0~32)

h-3. H.Size (0~100)

h-4. V.Size (0~100)

i. Reset All Setting

CONFIDENTIAL – DO NOT COPY

Page 3-7

File No. SG-0264

D. Parental：

a. PASSWORD

CONFIDENTIAL

–

DO NOT COPY Page 9-1

File No. SG-0264

Yes

Chapter 9 Trouble shooting

MONITOR DISPLAY NOTHING (PC MODE)

Start

LED is lighted

1. Is Power board output

+5VSB &DV12?

2. Is J1 connector good?

3. Is DC-DC OK?

4. Is U14 (+5V) working ok?

LED is lighting?

It is in power saving

1. Check video cable

2. Is the timing supported?

3. Check sync input

4. Check VGA SOG rout if analog

(SOG)

Is backlight on?

1.Check J1 PIN1

2.Is Power Board ok?

U13 no data out?

It means data to LVDS

1.Is J8 connecting OK?

2.Check J1 +5V & +12V

3.Is panel ok?

Check P5 D-sub Input correct

5. Check analog input route

END

CONFIDENTIAL

–

DO NOT COPY Page 9-2

File No. SG-0264

Yes

(TV,

COMPOSITE VIDEO ) IS NOT DISPLAY CORRECTLY

Start

Input signal good?

1. Check video

2. Check DVD player

U13 input correct?

1. Check P2(VIDEO) signal

2. Check signal between U13 (IF IN AV

mode)

LVDS output correct?

1. Check U13 :DV33&DV12&AV15&AV12

2. Check X1 is OK?

1. Check J8 Connect is good?

2. Is panel working ok?

END

U13 output correct?

1. Check LVDS LINE

2. Check U13 clock (60MHz)

3. Check LVDS 5V or 12V

CONFIDENTIAL

–

DO NOT COPY Page 9-3

File No. SG-0264

Yes

(COMPONENT)

IS NOT DISPLAY CORRECTLY

Start

Input signal good?

1.Check video

2.Check host’s setting

P3 input correct?

1.Check signal between P3

2.Check power 12V& 5v

U13 input correct?

1.Check signal between U14&P1

2.Check U13 Clock (60MHZ)

3.Check U13 :DV33&DV12&AV15&AV12

LVDS output correct ?

1.Check U13

2. Check LVDS 5V or 12V

1.Is J8 connected good?

2.Is panel working ok?

END

CONFIDENTIAL

–

DO NOT COPY Page 9-4

File No. SG-0264

Yes

(

HDMI) IS NOT DISPLAY CORRECTLY

Input signal good?

Start

1.Check video

2.Check host’s setting

U13 no data out ?

1.Check U13 power

2.Check between signal U13

3.Check U13 clock 60MHZ

1.Is J8 connected good?

2.Is panel working ok?

END

CONFIDENTIAL

–

DO NOT COPY Page 9-5

File No. SG-0264

Yes

The voltage is about + 12V while power switch on

1. J1 connection good

2. Check J1 Pin2,3,4 transform +5V_TUNER

3. Check power board

The voltage is about +5V while power switch on

1. J1 connection good

2. Check U13 OPWRSB & OPCTRL2 Pin

ROUBLE OF DC-DC CONVERTER

Start

J1 PIN9,10,11

J1 PIN 2,3,4

The voltage is about 5VSB

1. Check power board

2. Check power cable connection J1

U14 pin 5 6 7 8

U22,U15 pin2

The voltage is about +3.3V

U20 pin2

The voltage is about +1.8V

U21 pin2

The voltage is about +1.25V

U17 pin2

The voltage is about +3.3V

U19 pin2

The voltage is about +2.5V

U18 pi2

The voltage is about +1.1V

END

Page is loading ...

Vizio VW42L - 42 Inch LCD HDTV User manual

Brand: Vizio

Model: VW42L - 42 Inch LCD HDTV

Category: TVs & monitors

Type: User manual

This manual is also suitable for

VW42L FHDTV10A LPL

Download PDF

report

Vizio VW42L - 42 Inch LCD HDTV User manual

This manual is also suitable for

Vizio VW42L - 42 Inch LCD HDTV User manual

Related papers

Other documents