Generation Lighting 65661 Installation guide

Brand
Generation Lighting
Model
65661
Type
Installation guide

This manual is also suitable for

STEP 1
Thr
ead fixtur
e loop (H) to fixture.
STEP 1:
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-1435
1
12508
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
•
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
• To reduce the risk of fire, electric shock, or personal injury, mount
to outlet box or supporting system able to support the weight of
t
he fixture.
• If you are unclear as to how to proceed, contact a qualified
electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
•
Read instructions carefully.
• Save these instructions.
IMPORTANT SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
CLEANING
ORDERING PARTS
Secur
e mounting bar (A) to outlet box with outlet box scr
ews (not
supplied). Thr
ead nut (B) on nipple (C) so that 5 threads ar
e exposed
above nut (B). Thread nipple (C) into mounting bar (A) and secure
with nut (B). Thread screw collar (E) to nipple (C).
Using 2 pairs of pliers or chain br
eaks, open one link of chain (G) and
connect it to the fixture loop (H) at the top of the fixtur
e. Chain
should be opened outward, do not twist.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 2:
STEP 3:
INST
ALLATION
*OUTLET BOX
*OUTLET BOX
SCREWS
*WIRE CONNECTORS
SCREW COLLAR (E)
CANOPY (D)
MOUNTING BAR (A)
*GROUND WIRE
SCREW COLLAR
RING (F)
FIGURE 1 *NO
T SUPPLIED
CHAIN (G)
FIXTURE LOOP (H)
NIPPLE (C)
NUT (B)
STEP 4:
Slide the screw collar ring (F) and canopy (D), in that or
der
, over
chain (G). Open one link on the other end of the chain (G) and attach
it to the screw collar (E) which has been mounted to the ceiling
nipple (C).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETEL
Y
.
STEP 2
STEP 4
STEP 3
STEP 5
G
ROUNDING INSTRUCTIONS
:
The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (F) from the fixture and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar (A) if
uninsulated wire is on the mounting bar (A), connect the ground wire
(F) from the fixture and the outlet box to it using a small wire
connector (not supplied).
NEVER CONNECT GROUND WIRE TO
BLACK OR WHITE POWER SUPPLY WIRES.
INSTALLATION (continued) HC-1435
STEP 6:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (D) against ceiling and thread the screw collar
ring (F) to the screw collar (E) to secure.
Make sure no bare wires can be seen outside wire connectors.
Rest diffuser (K) on the inside lip of decorative ring (L).
FINAL ASSEMBLY
STEP 7
STEP 9:
STEP 5:
WIRING
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(
white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
Raise decorative ring (L) to the fixture ring (M) so mounting studs (O)
protrude through both rings. Secure by threading retaining screws (N)
onto mounting studs (O).
Install lamps (not supplied).
STEP 10:
STEP 8:
FIGURE 3
*NOT INCLUDED
TOP
DIFFUSERS
(I)
DIFFUSER
RET
AINING
SCREWS (J)
*OUTLET BOX
*OUTLET BOX
SCREWS
*WIRE CONNECTORS
SCREW COLLAR (E)
CANOPY (D)
MOUNTING BAR (A)
*GROUND WIRE
SCREW COLLAR
RING (F)
FIGURE 2 *NOT SUPPLIED
CHAIN (G)
FIXTURE LOOP (H)
NIPPLE (C)
NUT (B)
DECORATIVE
RING (L)
FIXTURE
RING
(M)
RET
AINING
SCREWS
(N)
MOUNTING
STUDS (O)
DECORATIVE
RING (L)
DIFFUSER (K)
Place washers over threaded holes of top dif
fuser mounting ar
ea.
Place top dif
fusers (I) onto washers and secure by threading top
dif
fuser retaining screws (J) through top diffusers (I), washers, and
threaded holes of top diffuser mounting area.
STEP 11:
STEP 7
STEP 9
STEP 6
STEP 10
STEP 10
STEP 11
STEP 10
  • Page 1 1
  • Page 2 2

Generation Lighting 65661 Installation guide

Brand
Generation Lighting
Model
65661
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents