FireplaceXtrordinair 98500509 User manual

FireplaceXtrordinair
Brand
FireplaceXtrordinair
Model
98500509
Type
User manual

This manual is also suitable for

FPX 32 DVS Artisan Face
Charcoal 98500507 Antique Copper 98500508 Antique Nickel 98500509
Page 1 of 4 17601079 - 5/10/10 © Travis Industries, Inc.
Compatibility
• DVS Insert • 31 DVI Insert
NOTE: On newer units (2008 or later), leave the glass on and move the face connector to the forward
position (see illustration below). For older units, remove the glass.
Face Connector
Bracket
Remove the face connector bracket
from the heater (on both sides).
Re-attach the face connector to the
heater using the forward mounting holes.
Warnings
Denatured
Alcohol
Soft Cloth
Plated Surfaces Warning:
Any marks left on the optional plated surface may become etched-in by the heat of the
appliance. Use denatured alcohol and a soft cloth to clean.
Soft Cloth
Anti-
Oxidizer
Copper Surfaces Warning:
Use the included anti-oxidizer to clean the optional copper surface. See the included instruction
sheet for full details.
Warning:
Make sure the heater has fully cooled prior to conducting service.
Packing List
1/4-20
Screws
10-24 Nuts
FPX 32 DVS Artisan Face
Charcoal 98500507 Antique Copper 98500508 Antique Nickel 98500509
Page 2 of 4 17601079 - 5/10/10 © Travis Industries, Inc.
Bracket Installation
Install the face mounting brackets to
the heater with the included nuts.
NOTE: The brackets
install with this pair of
closely spaced
flanges at the top.
FPX 32 DVS Artisan Face
Charcoal 98500507 Antique Copper 98500508 Antique Nickel 98500509
Page 3 of 4 17601079 - 5/10/10 © Travis Industries, Inc.
Face Installation
Attach the face using the four
bolts included with the face.
Make sure the door does
not open while installing.
Adjustable
Wrench
FPX 32 DVS Artisan Face
Charcoal 98500507 Antique Copper 98500508 Antique Nickel 98500509
Page 4 of 4 17601079 - 5/10/10 © Travis Industries, Inc.
Opening the Control Door
Warning:
The face becomes very hot during operation. Use the included handle open the control and
take care to not touch any of the hot surfaces.
Use the pull tool
on either side to
disengage the
hinges.
Note how the hooks on the tool insert
into the triangle-shaped holes.
Control Door
When removing the
pull tool, make sure
it does not damage
the hearth.
Pull Tool
(included
with face)
Adjusting the Control Door
The control is adjsuted at the factory. See the directions below if further adjustment is necessary.
Back of Face (with face removed)Bullet Catch
This bullet-shaped device holds the control door
upright. To tighten or loosen the catch, simple
rotate it (it is threaded inside the assembly).
Adjust this nut to tighten
or loosen the friction of
the hinge.
Back of Bullet
Catch
These two nuts hold the
bullet catch assembly.
If the top of the control
door is not aligned,
these nuts can be
loosened to re-align the
bullet catch assembly.
Access
Panel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

FireplaceXtrordinair 98500509 User manual

FireplaceXtrordinair
Brand
FireplaceXtrordinair
Model
98500509
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents