LG WM-L640V Owner's manual

*MFL68006802*

P/NO : MFL68006802(1503-REV00)

Printed in Korea

OWNER’S MANUAL

Please read this manual carefully before operating the your set and retain

it for future reference.

WM-L640V

WM-P640V

www.lg.com

Wall

Mounting

Bracket

2

ENG

ENGLISH

CONTENTS

3 SAFETY INSTRUCTIONS

4 Precaution in Installation

4 Precaution in Movement

5 PRODUCT COMPOSITION

6 INSTALLATION GUIDE

6 Preparing the Multi-Vision to Be Attached to Product

7 Fixing the Product to Wall

10 Connecting Multiple Products

12 Mounting a Multi-Vision to the Product

14 TRANSFORMATION OF PRODUCT

14 Reassembly for 55-in Multi-Vision

16 PRODUCT OPERATION

18 PRODUCT SPECIFICATIONS

3

SAFETY INSTRUCTIONS

ENG

ENGLISH

If you are a professional installer, please read this manual carefully before installing the product.

After installing the product according to the manual, ensure that the user also reads the manual carefully.

After reading the manual, please keep it handy for future reference.

The product should be installed by a qualified

professional specified by the retail store.

Installing the product without a qualified profes-

sional is dangerous and may cause personal

injury.

When moving or replacing the product after

installation, contact a qualified installer speci-

fied by the retail store.

Installation or movement of the product must be

carried out by a skilled professional. If unqualified

persons move and install the product, it may cause

safety issues.

The product should be installed where its

weight can be fully supported.

If the product is installed on a weak surface, the

product may fall, causing injury.

Do not hang on this product or apply any

shock to it.

The product may fall and cause injury.

Follow the instructions in the manual to prop-

erly install this product.

If you do not follow the instructions, the product

may be installed incorrectly and cause serious

injury or damage to the product.

During installation, check whether the wall is

strong enough to hold the product and use the

anchors and screws provided.

If you use anchors and screws that are not speci-

fied by the manufacturer, they may not hold the

weight of the product, causing safety issues.

Do not clean the product with wet towels and

do not place a heater or humidifier underneath

it.

Moisture permeating into the product, including

through steam and heat, may result in a fire, elec-

tric shock or damage to the product.

Make sure that the power cord is removed from

the outlet before installing the product.

Otherwise, it may cause an electric shock or fire.

To install or adjust the height of the product,

two or more people are needed.

If you try to install or move the product alone, it

may fall, causing injury or damage to the product.

When drilling holes into the wall, make sure

you use a drill and drill bit with the specified di-

ameter. Ensure that you also follow the instruc-

tions regarding the depth of the holes.

Otherwise, the product may be installed incorrectly

and cause safety issues.

Keep this product away from sprinklers, sen-

sors, high-tension wires, and power sources.

Do not install it in a location where vibrations

or impact shocks are likely to occur.

Wear working gloves when installing the prod-

uct. Do not use bare hands.

Otherwise, it may cause personal injury.

SAFETY INSTRUCTIONS

WARNNING

CAUTION

4

SAFETY INSTRUCTIONS

ENG

ENGLISH

Check the wall material and thickness of the finish-

ing material.

You can use the anchors and screws provided with

the TV set for the wall made with concrete, light-

weight concrete, soft fieldstone, hard fieldstone,

brick or cellular block.

Do not mount the device on walls made with plas-

ter board or medium-density fiberboard (MDF). In

this case, the anchor and screws must be inserted

into the concrete behind the finish. If there is no

concrete on the other side, then you must install a

separate hanger first to fix the anchors and bolts

to.

When installing it on a wall not specified in this

manual, make sure each fixing point withstands an

uplifting load of 70 kgf (686 N) and a shearing load

of 100 kgf (980 N) or more.

When installing multiple Multi-Visions, be careful to

avoid vertical and horizontal impacts between the

Multi-Visions. Strong shocks may cause the Multi-

Visions to malfunction.

When transporting the product, check whether the safety screws (black) are fastened to the location illus-

trated in the figure below. If the safety screws (black) are not fastened, it may result in personal injury due

to an unexpected movement of the product.

Precaution in Installation

Precaution in Movement

WARNNING

Precautions when mounting Multi-Visions

The weight of the Multi-Vision installed on the

product must be equal to or less than 40 kgf.

5

PRODUCT COMPOSITION

ENG

ENGLISH

PRODUCT COMPOSITION

Please check whether all the components are included in the box before using the product. If there are any

missing components, contact the retailer where you purchased the product. Note that the accessories may

look different from those shown here.

Wall Mounting Anchor, 12 EA

Guide Spacer, 4 EA Guide Spacer Fixing

Screw

(M6 x L40) 4 EA

Safety Clip, 2 EA

Wall Mounting Bracket

Fixing Screw

(Used for inter-product fixing)

(M4 x L10) 4 EA

Wall Mounting Bracket

Fixing Screw

(Used for fixing to wall)

(

5 x L65) 12 EA

Owner's Manual



Always use genuine components to ensure safety and product performance.



The product warranty will not cover damage or injury caused by the use of counterfeit components.



The accessories supplied with your product may vary depending on the model.



Without prior notice, all information and specifications in this manual are subject to change to im-

prove the performance of the product.

CAUTION

NOTE

6

INSTALLATION GUIDE

ENG

ENGLISH

INSTALLATION GUIDE



If the screws are not fully tightened when you fix the guide spacers, check the length of the screws and refer to

the technical service manual.

NOTE

1

Place the multi-vision on a table with its screen

facing downward.

- Make sure that you place it on soft clothing or

a cushion on the flat surface

2

Remove any screws that have been installed

on the fixing area of the multi-vision wall

mounting bracket.

3

Check if the guide spacer is at the maximum

value.

4

Place the guide spacers over the screw holes

on the Multi-Vision. Tighten the guide spacers

with the guide spacer fixing screws (M6 x L40).

5

Turn the screw until the gap between the guide

spacer and the Multi-Vision has about 1 mm

remaining.

- The picture may differ from the actual product.

Preparing the Multi-Vision to Be Attached to Product

Guide Spacer Fixing Screw

Guide Spacer

Multi-vision

Guide Spacer Screw

Maximum

1 mm

7

INSTALLATION GUIDE

ENG

ENGLISH

Fixing the Product to Wall

Wall

Hole

Wall Mounting Anchor

1

On the position where the wall mounting

anchor will be fixed, drill a hole with a depth of

between 80 mm - 100 mm using a drill bit Ф 8

mm.

- Use the Ф 8 mm drill bit for concrete and a

hammer (impact) drill.

2

Clean out the drilled hole.

3

Insert the wall mount anchor to the hole (using

a hammer).

4

Place the wall mounting bracket close to the

wall along the hole.

5

Insert the wall mounting screw into the hole

and tighten it.

Drill

Wall Mounting Screw

8

INSTALLATION GUIDE

ENG

ENGLISH

Install the product on the wall using the fixing screws for the wall mounting bracket.

Install the product with the arrow marked on it facing upward.

WM-L640V

Page is loading ...

10

INSTALLATION GUIDE

ENG

ENGLISH

Connecting Multiple Products

WM-L640V

1

Connect the fixing screws for wall mounting bracket on the up, down, left and right side.

2

Insert the fixing screws to the holes as shown in the figure and turn them.

- The picture may differ from the actual product.

Page is loading ...

12

INSTALLATION GUIDE

ENG

ENGLISH

Mounting a Multi-Vision to the Product

- The picture may differ from the actual product. Please install in the following order:

1

Check if the up/down adjustment piece is located at the uppermost position.

2

Remove the two safety screws. If the safety screw is fastened, the product cannot be moved to the left or

right.

3

As shown in the figure, hang the multi-vision combined to the guide spacer using the holes on the product.

4

Align the height of the product and the Multi-Vision by adjusting the up/down adjustment piece downwards.

- If you install multiple products, accurately align the products and the Multi-Vision from bottom to top.

Otherwise, installing products that will be located at the top will be difficult.

5

Fit a safety clip to prevent the installed multi-vision from coming loose. It should be inserted to the guide

spacer hole at the bottom of both sides.

WM-L640V

1

2

3

5

4

Safety Screw (black)

Up/Down Adjustment Screw

Product Multi-Vision

13

INSTALLATION GUIDE

ENG

ENGLISH

WM-P640V

1

3

2

4

5

Up/Down Adjustment Screw

Safety Screw (black)

Product Multi-Vision

14

TRANSFORMATION OF PRODUCT

ENG

ENGLISH

TRANSFORMATION OF PRODUCT

Reassembly for 55-in Multi-Vision

- The picture may differ from the actual product.

1

Remove the screws (32 pieces) shown in the red dotted-line circle in the figure below.

2

If you move the bracket in other directions, you can see all of the screw holes that are in different loca-

tions. Reassemble the bracket by fastening the screws (32 pieces).

WM-L640V

Changed location

Original location

Changed location

15

TRANSFORMATION OF PRODUCT

ENG

ENGLISH

1

Remove the screws (32 pieces) shown in the red dotted-line circle in the figure below.

2

If you move the bracket in other directions, you can see all of the screw holes that are in different loca-

tions. Reassemble the bracket by fastening the screws (32 pieces).

3

When the assembly is completed, fasten the safety screws (black) for safety during transport. The

safety screws (black) can be fastened when the product is aligned in the center.

WM-P640V

The screws in this location can be seen only

when you move the product to the left or right.

To move the product to the left or right, the

safety screws must be removed.

Original location

Changed location

Original location

Changed location

Safety Screw

Safety Screw Hole

16

PRODUCT OPERATION

ENG

ENGLISH

PRODUCT OPERATION

Horizontal Adjustment



When sliding the product to the left or right, be careful to prevent injury to your hands.

CAUTION

Left Right

WM-L640V

WM-P640V

Left Right

Product Type Left Right

Product for 47-inch

Multi-Vision only

131.5 mm 131.5 mm

Product for 55-inch

Multi-Vision only

215.5 mm 215.5 mm

Product Type Left Right

Product for 47-inch

Multi-Vision only

42.5 mm 42.5 mm

Product for 55-inch

Multi-Vision only

89.5 mm 89.5 mm

17

PRODUCT OPERATION

ENG

ENGLISH

Back & Forth Adjustment

From the back or side of the product, use a Phillips screwdriver or a hexagon socket screw key in the guide

spacer hole and turn the guide spacer to move the Multi-vision forward or backward.

If you turn the guide spacer counterclockwise from the back of the product, the Multi-vision moves forward.

If you turn it clockwise, the Multi-vision moves backward.

Vertical Adjustment

The figure shows the WM-L640V model. For the

WM-P640V model, you can also make the back &

forth adjustments by turning the guide spacer.

The figure shows the WM-L640V model. For the

WM-P640V model, you can also make the vertical

adjustment.

Turn this part to make the vertical adjustment.

Clockwise: Forward

Counterclockwise:

Backward

Moves forward

Moves backward

18

PRODUCT SPECIFICATIONS

ENG

ENGLISH

PRODUCT SPECIFICATIONS

Product dimensions

(Width x Height x depth)

Product for 47-inch Multi-Vision only 1043.9 mm x 589 mm x 44.5 mm

Product for 55-inch Multi-Vision only 1212.4 mm x 683.2 mm x 44.5 mm

Package dimensions

(width x height x Depth)

1180 mm x 725 mm x 140 mm

Wall Mounting VESA

speciﬁ cations

600*400

Weight (kgf) 12 kgf

Max. tensile load (kgf) 40 kgf

Position adjustment Vertical adjustment in total: approx. 15 mm

Horizontal adjustment in total: approx. 263 mm

(Product for 55-inch Multi-Vision only approx. 431 mm)

Forward: min. approx. 10 mm

WM-L640V

Width

994

549

252

60

894

Depth

(Unit : mm)

Height

19

PRODUCT SPECIFICATIONS

ENG

ENGLISH

Product dimensions

(width x height x depth)

Product for 47-inch Multi-Vision only 589 mm x 1043.9 mm x 44.5 mm

Product for 55-inch Multi-Vision only 683.2 mm x 1212.4 mm x 44.5 mm

Package dimensions

(width x height x depth)

1180 mm x 725 mm x 140 mm

Wall Mounting VESA

speciﬁ cations

600*400

Weight (kgf) 10.9 kgf

Max. tensile load (kgf) 40 kgf

Position adjustment Vertical adjustment in total: approx. 11 mm

Horizontal adjustment in total: approx. 85 mm

(Product for 55-inch Multi-Vision only approx. 179 mm)

Forward: min. approx. 10 mm

WM-P640V

Width

539

239

(Unit : mm)

Depth

Height

1004

818.4

379.2 439.2

Page is loading ...

LG WM-L640V Owner's manual

LG WM-L640V Owner's manual

Related papers

Other documents