International Controls & Measure ICM492C Installation guide

Brand: International Controls & Measure

Model: ICM492C

Type: Installation guide

ICM492

Single Phase Digital Line Voltage Monitor

Reliable protection of single phase systems against adverse line voltage conditions

SPECIFICATIONS

User Adjustable Settings:

•Voltage setpoint:95-280V

•Anti-short cycle time delay:0-720sec.

•Over voltage setting:5-25%

•Under voltage setting:5-25%

•Control mode:OnandOff

•Response time:0.1to10seconds

Inputs:

•Line voltage:80to300VAC

•Control voltage:24to240VAC

•Frequency:50/60Hz

•Accuracy:±2%

•Low power consumption:Max50mA@120V,

 Max100mA@240V

Output:

•Type:dryrelaycontacts

•Form:SPDT

•Relay contact ratings:

 –N.C. Contacts:10Aresistive@277VAC

 –N.O. Contacts:10Aresistive@277VAC

•Connection Terminals:0.25”malefast-on

Mechanical:

•Case dimensions:3”Lx3.2”Wx1.35”H

•Unit weight:0.36lbs.

Environmental:

•Operating temp. range:-30°Cto+70°C

•Storage temp. range:-40°Cto+85°C

•Maximum operating/storage relative humidity:

95%non-condensing

7313 William Barry Blvd., North Syracuse, NY 13212

(Phone) 315-233-5266 (Toll Free) 800-365-5525

(Fax) 315-233-5276

www.icmcontrols.com

LII335-3

Constantly monitors and displays line

voltage. Protects against Over and Under

voltage, and Rapid Short Cycling caused by

Transient Faults and Power Interruptions

TheICM492isspecicallydesignedtomonitorline

voltageandguardsinglephaseequipmentagainst

damagecausedbyunderandoverlinevoltage

conditionsandrapidshortcycling.Recordslastve

faults.

DESCRIPTION

•UniversalLineVoltage

Input

•Easy-viewBacklitDigital

Display

•RMSVoltageMonitoring

•5-faultmemorystorage

•AdjustableVoltageSet

Point

•AdjustableOverVoltage

SetPoint

•AdjustableUnder

VoltageSetPoint

FEATURES

•AdjustableAnti-Short

CycleTimeDelay

•AdjustableResponseon

FaultTime

•ControlMode

•5-FaultMemory

•UniversalControl

VoltageInput

•HeavyDutySPDTRelay

Output

TheICM492continuouslymonitorsincominglinevoltage

forfaultsanddisplaysRMSvoltageonthedigital

display.Whenlinevoltageisappropriate,ICM492closes

theCOMandN.O.relaycontacts.Whenincomingline

voltageisoutsideofuserselectedparameters,ICM492

willclosetheCOMandN.C.relaycontactsandindicate

afaultconditionbyashingFAULTondisplay.Theunit

recordsthelastvefaults,storingthehighestandlowest

voltagereadingsthatcausedthefault.TheUP,DOWN

andSELECTbuttonsarepressedsimultaneouslyto

clearthefaultsfrommemory.TheSELECTmenuhas

thefollowinguseradjustablesettings:voltagesetpoint,

timedelay,overvoltagepercentage,undervoltage

percentage,controlmode,andresponsetime.Time

delaypreventsshortcyclingwhenfaultnolongeris

presentandrapidpowerinterruptions.Theresponse

timeonthefaultconditioncanbeadjustedtohelp

reducenuisancetripsfromtransientfaults.When

ControlModesettingisselectedONthenICM492will

closeCOMandN.O.relaycontactsonlywhencontrol

voltageispresentatControlVoltageterminalsandthe

linevoltageisgood.Therelaycontactscanbeused

todirectdrivetheloadaslongascurrentratingisnot

exceeded.

MODE OF OPERATION

!!! WARNING !!!

ElectricalShockHazard

• Verify power is disconnected by removing a fuse

or opening a circuit breaker before making any

connections.

• This control should be installed by a trained technician.

• Incorrect installation can cause personal injuries,

property damage or death.

• Follow all local & national codes while installing control.

!!! DANGER !!!

 Verify power is disconnected by removing a fuse or opening a circuit breaker before making

any connections or injury or death can result.

1. Disconnectpower.

2. MountICM492securelyagainstthemetalchaisesofthesysteminawaterproofenvironment.

3. Ifacontactororarelayisusedinthesystem(seeFig.1)tocontrolpowertotheloadthen:

 a. MakeL1andL2connections.

 b. Cutthewirethatpowersthecontactor/relaycoil,stripandplace1/4”femalespadeterminalsonthem.

 c. PlugfemalespadeterminalsonCOMandN.O.terminalsofICM492.

4. Shouldyouchoosetodrivetheloaddirectly(seeFig.2)usingrelaycontactsofICM492then:

 a. MakesurethatloadcurrentratingdoesnotexceedcurrentratingofICM492relaycontacts.

 b. Cutthelinethatpowerstheload,stripandplace1/4”femalespadeterminalsonthem.

 c. PlugfemalespadeterminalsonCOMandN.O.terminalsofICM492.

5. ShouldyouchoosetouseacontrolsignalatControlVoltageinputterminalsthen:

 a. Usetwowireswith1/4”femalespadeterminalsonthemtoplugonControlVoltageterminalsofICM492.

 b. Tapintocontrolsignalwiththeotherendofthewires.

6. PressSELECTbuttontoentertheselectmenu.

a. UseUpandDownarrowstoadjustfeaturesettings.

b. MakesurethattheControlModeisONifthecontrolsignalisusedatControlVoltageterminals.

INSTALLATION

WIRING DIAGRAMS

Figure 1 Figure 2

Motor

*Notnecessarybutrecommended1Ampfuse.

PressSELECTtoentermenusetup

• VOLTAGESETPOINTdisplays(95–280VAC)

• Adjustthistomatchthevoltageofyoursystem.

• Useupordownbuttontoadjust.

PressSELECTfornextscreen

• TIMEDELAY(Lockout)displays(1-720seconds)

• Thisistheamountoftimeyoursystemwillbelocked

outafterafault.

• Useupordownbuttontoadjust.

PressSELECTfornextscreen

• OVERVOLTPERCENTAGEdisplays(5-25%)

• Thisisthepercenttheactualvoltagemustbeabove

yourSetVoltageforanoverfaulttooccur.

• Useupordownbuttontoadjust.

PressSELECTfornextscreen

• UNDERVOLTPERCENTAGEdisplays(5-25%)

• Thisisthepercenttheactualvoltagemustbebelow

yourSetVoltageforanunderfaulttooccur.

• Useupordownbuttontoadjust.

SELECT MENU SETUP

PressSELECTfornextscreen

• CONTROLMODEdisplays(OFF-ON)

• WhensettoON,therelaycontactscloseonlywhen

linevoltageconditionsaregoodandvoltageis

presentattheControlVoltageterminals.

• Useupordownbuttontoadjust.

PressSELECTfornextscreen

• RESPONSETIMEdisplays(.01-10seconds)

• Thisistheamountoftimethefaultconditionmust

existbeforeyoursystemisturnedoff.

• Useupordownbuttontoadjust.

PressSELECTfornextscreen

• FAULT1-5displays

• Thisisthevoltageofthefaultthathasoccurred.

• –––Indicatesnofaultisinmemory

NOTE:Faults can be cleared by simultaneously

pressing the UP, DOWN and SELECT buttons

after exiting SELECT Menu Setup.

After15secondsofbuttoninactivity,thecontrolexits

SELECTMenuSetupscreen.

International Controls & Measure ICM492C Installation guide

International Controls & Measure ICM492C Installation guide

International Controls & Measure ICM492C Installation guide

Other documents