Installation
Instructions
Overthe Range
Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - Savethese
instructions ti)r local inspe{tor's use.
• IMPORTANT - Obse,,-eall
governing codes and ordinances.
• Note to Installer - Be sure to leave these
instructions xdth the ( onsumer.
• Note to Consumer - Keep these
instructions fi)r flmue reference.
• Skilllevel- Installationofthisappliancerequires
basic mechanical and electrical skills.
• Proper installation is the responsibility of the installer.
• Product thilure due to improper installation is not
covered under the Warranty.
//
Need Help?
For customers in the United States, call: 1-800-944-9044
For Canadian customers, call: 1-866-213-9397 (English)
1-800-668-4606 ext. 8199 (French)
READ CAREFULLY.
KEEP THESE INSTRUCTIONS.
P/N 316137211
Installation Instructions
CONTENTS
General information
Important Safety Instructions .................................. 3
Electrical Requirements .......................................... 3
Hood Exhaust ...................................................... 4-5
Damage - Shipment/Installation ............................ 6
Parts Included .......................................................... 6
Tools You Will Need ................................................ 7
Mounting Space ...................................................... 7
Step-by-step installation guide
Placement of Mounting Plate .............................. 8-10
Removing tile Mounting Plate ...................... 8
Finding the Wall Studs .................................. 8
Determining Wall Plate I,ocation .................. 9
Aligning the Wall Plate ................................ 10
Installation Types ............................................ 11-22
[]Outside Top ............................
Exhaust
12-14
Attach Mounting Plate to Wall ............ 12
Preparation of Top ( abinet ................ 13
Checking fin Proper Damper
Operation ............................................ 13
Mount the Microwave Oven .......... 13-14
Adjust the Exhaust Adaptor. ............... 14
Connecting Ductwork .......................... 14
[]Outside Back Exhaust 15-18
Preparing Rear Wall for
Outside Back Exhaust .................... 15-16
Attach Mounting Plate to Wall ............ 16
Preparation of Top ( abinet ................ 16
Adapting Microwave Blower
tot Outside Back Exhaust ...................... 17
Mount the Microwave Oven ................ 18
Recirculating ........................................ 19-22
Attach Mounting Plate to Wall ............ 19
Preparation of Top ( abinet ................ 19
Che(k Mi_rowave Assemb b................. 20
Adapting Mi_rowave Blower
for Recirculation .......................... 20-21
Mount the Microwave
Oven .............................................. 21-22
Installing the ( har_ oal Fiher. ............. 22
Before You Use Your Microwave .......................... 23
2
Installation Instructions
mMPORTANT SAFETY mNSTRUCTmONS
This produ( t requires a three-pro_g grounded
omlet. The inaalier must perform a groined (::omimfi b-
check on the power omlet box before beghming the
iustallafion to insme d_at d_e omlet box is properly
grom_ded. If uot properly grom_ded, or if d_e omlet
box does uot meet electrical requiremeuts noted
(mbder ELECTRK;AL REQUIREMENTS), a
qmllified electrician should be employed to
correct auy defibieuries.
(L&UTION: For personal
safety, remove house fuse
or open circuit breaker
before begh'lrfing irlstallation
to avoid severe or fatal
shock injury.
(k&UTION: For personal safety, the mounting surface
must be capable of supporting the cabinet load, ir_
addition to the added weight of"this 63-85 pound
(28.648.6 kg) product, plus additional oven loads of
up m 50 pounds (22.7 kg) or a total weight of 113-135
pounds (51.341.2 kg).
CAUTION: For personal safety, this product carmot
be installed ir_cabinet arrangements such as aa_island or
a peninsula° It must be mounted to BOTH a top cabkmt
AND a wall.
NOTE: Fur easier installation and personal safety, it is
recoimlaended that two people install this product°
IMPORTANT--PLEASE READ (LAREFULLY. FOR
PERSONAL SAFETY, THIS APPLIANCE MUST BE
PROPERLY GROUNDED TO AVOID SEVERE OR
FATAL SHOCK°
The power cord of this applim-_ce is equipped with a
three-prong (g_'oundlng)
plug which mates with a
standm-d three-prong
(g_'oundmg) wall receptacle
to minimize the possibility
of electric shock hazard
from this appliance.
Insureproper
groundexists
beforeuse
You should have the wall receptacle and circuit checked
by a qualified electrician to make sure the receptacle is
properly grounded.
Where a standard two-prong wall receptacle is
encountered, it is ve_T importam to have it replaced
with a properly g_ounded three-prong wall receptacle,
installed by a qualified electrician.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT,
DEFORM OR REMOVE ANY OF THE PRONGS
FROM THE POWER CORD. DO NOT USE WITH
AN EXTENSION CORD.
ELECTRICAL
REOUIREMENTS
Product rating is 12(1vohs AC, 6(t Hertz, 15 amps and
[,58 kth)x_aus. This p5odu(t must be (ouue(ted u) a
supply circuit of d_e proper voltage and h:equen(y
Wire size must couform to the requiremems of the
Nathmal Electrical Code 555d_e prevailing lo(al code
for this kilo_att rating The pox_er supply cord and
plug should be brought u) a separate 15 u5 2(1ampere
brau( h (ir(uit siugle grom-bded ()inlet, The (ruder 1)55×
should be located in the cabinet above the micro_a_e
o_en, The omlet box and supply (::ir(uitshould be
installed b)ra qualified electrician and conform u) fl_e
Nathmal Electrical Code 555d_e prevailiug local code.
3
Installation Instructions
HOOD EXHAUST
NOTE: Read these next two pages only if you plan to vent your exhaust to the
outside. If you plan to recirculate the air back into the room, proceed to page 6.
OUTSIDE TOP EXHAUST (EXAMPLE ONLY)
Tile fi)llo_fing chart des(rihes an example of one possihle
du(twork installation.
DUCT PgECES
RoofCap
12Ft.StraightDuct
(6" Round)
Rectangular-to-Round
TransitionAdaptor*
EQUWALENT NUMBER
LENGTH x USED
24Ft. x (1)
(7.32m)
12Ft. x (1)
(3.66m)
5Ft. x (1)
(1.52m)
Equivalentlengthsofduct piecesare basedonactualtests and
reflectrequirementsfor goodventingperformancewith anyventhood.
Total Length
EQUIVALENT
LENGTH
24 Ft.
(7.32m)
12Ft.
(3.66m)
5Ft.
(1.52m)
41 Ft. (12.50 m)
*IMPORTANT: If a rectala_ular-to-rnund transition adaptor is used, the hnttom corners of the damper will
have to he (tit to fit, using tile tin snips, in order to allow free inovelnent of the dalnper.
OUTSIDE BACK EXHAUST (EXAMPLE ONLY)
The following chart des(rihes an example of one possihie
du(twork installation.
[
DUCT PIECES
%
EQUIVALENT NUMBER EQUIVALENT
LENGTH* x USED = LENGTH
Wall Cap 40Ft. x (1) = 40Ft.
(12.19m) (12.19m)
3 Ft.StraightDuct
3W' x 10"Rectangular)
90° Elbow
3 Ft. x (1)
(91.44cm)
10Ft. x (2)
(3.05m)
3 Ft.
(91.44cm)
20Ft.
(6.10m)
Equivalentlengthsof ductpiecesare basedonactualtests and
reflectrequirementsforgoodventingperformancewith anyvent hood.
Total Length = 63 Ft. (19.20 m)
NOTE: For ha('k exhaust, care should he taken to align exhaust with spa(e hetween studs, or wall should he prepared
at the tilne it is constructed by leaving enough space between the wall studs to accolnlnodate exhaust.
4
Installation Instructions
NOTE: If you need to install ducts, note that the total
duct length of 3V/' x 10" rectangular or 6" diameter round
duct should not exceed 140 equivalent feet (42.67 m).
Outside ventilation requires a HOOD EXHAUST
DU(T. Read the follo_dng carefiflly.
NOTE: It is important that venting be installed using
the most direct route and with as tew elbows as possible.
This ensures cleat venting of exhaust and helps prevent
blockages. Also, make sure dampers swing freely and
nothing is blocking the ducts.
Exhaust connection:
The hood exhaust has been designed to mate with a
standard 3V/' x 10" rectangular duct.
If a round duct is required, a rectangular-to-round
transition adaptor must be used. Do not use less than
a 6" diameter duct.
Maximum duct length:
For satisLt{ to D air movement, the total du{t length of
3]/, " x 10" rectangular or 6" diameter round duct should
not exceed 140 equivalent feet (42.67 m).
Elbows, transitions, wall and roof caps,
etc., present additional resistance to airflow and are
equiwtlent to a section of straight duct which is longer
than their actual physical size. When calculating the
total duct length, add the equivalent lengths of all
transitions and adaptors plus the length of all straight
duct sections. The chart below shows you how to
calculate total equivalent duclwork length using the
approximate teet of equivalent length of some typical
ducts.
EQUIVALENT NUMBER EQUIVALENT
DUCT PIECES LENGTH x USED = LENGTH
Rectangular-to-Round 5Ft. x ( } = Ft.
TransitionAdaptor* (1,52m) (m)
Wall Cap 40 Ft. x ( ) = Ft.
(12.19m) (m)
()_ go°Elbow 10Ft. x ( ) = Ft.
(3,05m) (m)
{_ 45° Elbow 5Ft, x ( ) = Ft.
(1,52m) (m)
go° Elbow 25 Ft. x ( ) = Ft.
(7,62m) {m)
45° Elbow 5Ft. Ft.
( )
X
(1£2 m} (m)
Roof 24 Ft. ( } Ft.
Cap
×
(7,32m} (m)
StraightDuct6" Roundor 1Ft. x ( ) = Ft.
374"x 10"Rectangular (30,48cm} (cm)
Total Ductwork = Ft. {m}
* IMPORTANT: lla I('LlalI_ulaI-I(}-F(}uI3d tlansiti(}n E( uivalent 1€nNhs of dtlcl Die (:€s arc bas((l ()ll a(:tua[ tcsIs
adaplor is used, th( botlom Comers of the dam )(r and r_flecI te( uirements lbr good vc n/ing peHbnnance with
willhaveIobe cuttoill, using the tinsnips,inor(let al]x venthood.
to all{*_freenaoxementoftla_damper.
5
Installation Instructions
DAMAGE - SHmPMENT/
* If the unit is damaged in shipment, re_uvn d_e unh
_o d_e s_ore h_whhh h was bough_ for repair or
* If the unit is damaged by the customer, rep_ir 05
veplacemem is d_e responsibility of d_e _us_omer.
ff the unh is damaged by the installer (if od_er
be made by a5v_Hsgemem be_weesr5 ( us_omer a55(]
is_ss_allev.
PARTS INCLUDED
HARDWARE PACKET
PART QOANTITY
WoodScrews 2
(Y/' x2")
ToggleBolts(and 4
wingnuts)(_(' x3'9
Self-aligningMachine 3
Screws(IA"-28x 31//9
NylonGrommet 2
(formetalcabinets)
28"(71.12cm} 2
Piecesof FoamTape
You will find the installation hardware contained in
a packet with the unit. Check to make sure you have
all these parts.
NOTE: Some extra parts are included.
ADDITIONAL PARTS
PART
TopCabinet
Template
Installation
Instructions
Separately
Packed
Grease
Filters
QUANTIFY
1
6
Installation Instructions
TOOLS YOU WILL NEED
#1 and#2 Phillipsscrewdriver
Pencil
Tinsnips(forcutting
damper,if required)
Scissors
(to cut template, if necessary)
Gloves
Safety goggles
Saw(saber,holeorkeyhole)
Rulerortapemeasureand
t edge
Electricdrillwith¾_"VS"and%"
drillbits
Stud finder er Hammer (optional)
Level
(optional)
Fillerblocksor scrap
woodpieces,if needed
fortop cabinetspacing
(usedonrecessedbottom
cabinetinstallationsonly)
Duct and masking tape
MOUNTING SPACE
0 t0m 0 0f
cabinet needs to
be30"(76.2cm)
_or morefromthe
[ '"T -- cookingsurface
30"(76.2cm)rain.
Backsplash
66"(167.64cm)
ormorefrom
thefloortothe
topofthe
microwave
NOTES:
• The space between the cabinets must be 30"
(76.2 cm)xdde and flee of obstn_ctions.
• If the space between the cabinets is greater
than 30" (76.2 cm), a Filler Panel Kit may be
used to fill in the gap between the microwave
oven and the cabinets. Your Owner's Manual
contains the kit number fi>ryour model.
" This microwave oven is fi)r installation over
ranges up to 36" (91.44 cm)wide.
" If you are going to vent your microwave oven
to the outside, see Hood Exhaust Section for
exhaust duct preparation.
" When installing the microwave oven beneath
smooth, fiat cabinets, be careful to follow the
instructions on the top cabinet template for
power cord clearance.
7
Installation Instructions
I- PLACEMENT OF THE MOUNTING PLATE
I'_ REMOVING THE MICROWAVE
OVEN FROM THE CARTON/
REMOVING THE MOUNTING
PLATE
[] Remove tile installation instructions, filters, glass
tray and the small hardware bag. Do not remove
the Styroloam protecting the front of tile oven.
[] Fold back all 4 carton flaps flflly against carton
sides. Then careflflly roll the oven and carton over
onto the top side. The oven should be resting in
the SUrolbam.
1 ;arton
[] Pull tile carton up and off tile oven.
[] Remove and properly discard plastic bags.
Mounting
Plate
[] Remove the 2 screws tiom the mounting plate.
This plate will be used as the rear wall template
and ti)r mounting. You may discard these screws.
I-_ FINDING THE WALL STUDS
nter
[] Find d_e studs, using one of _l_e follo_dng
me_hods:
A. Stud finder - a magnetic device which
loca_es nails.
OR
B. Use _ hammer _o _ap lighdy _cross d_e
mounting smT_a(e _o find a solid sound.
This will indicme _ stud lo(afion_
[] A_ler locating d_e stud(s), find d_e cemer by
probing d_e wall whh a small nail _o find d_e edges
of d_e stud. Then place a mark half\_ay between d_e
edges. The cemer of any a(]iacem studs should be
1_i"or 24" (40A_4cm or _0.96 cm) f_om d_is mark.
[]Draw a line down d_e cemer of d_e studs.
THE MICROWAVE MUST BE CONNECTED TO
AT LEAST ONE WALL STUD.
8
Installation Instructions
DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET
Plate position - beneath flat bottom
cabinet
MountingPlateTabs
i the CabinetBottom
-::
c I)iLUIIIFL
II I II
At least 30" (76.2 cm), u to
S t"
6 (g!.44cm)
Plate position - beneath framed recessed
cabinet bottom
Mounting Plate Tabs
Touching the Back
Frame
tl
30" (76.2 cm) to Cooktop
Plate position - beneath recessed bottom
cabinet with front overhang
Mounting Plate with
Tabs Below Cabinet
Bottom the Same
Distance as the Front
_gDepth
Your cabinets may have decorative trim that interferes
with the microwave installation. Remove the decorative
trim to install the microwave properly and to make it
level.
THE MICROWAVE MUST BE LEVEL.
Use a level to make sure the cabinet bottom is level.
If the cabinets have a flont overhang only, with no
back or side flame, install the mounting plate down
the same distance as the flont overhang depth. This
will keep the microwave level.
[] Measure the inside depth of the flont overhang.
[] Drmva horizontal line on the back wall an equal
distance below the cabinet bottom as the inside
depth of the fiont overhang.
[] For this type of installation with fiont overhang only,
align the mounting tabs with this horizontal line, not
touching the cabinet bottom as described in Step D.
tt
30" (76.2 cm)to Cooktop
9
Installation Instructions
ALIGNING THE WALL PLATE
Hole
1
HoleCJ;
CAUTION: Wear gloves
to avoid cutting fingers on
sharp edges.
) (
t
I Draw a Vertca
i LineonWall
u_-- fromCenterof
i T°pCabinet ._
%,"
HoleD ',
[] Draw a vertical line on the wall at tile center of tim 30"
(76.2 cm) wide space.
[] Use tile mounting plate as the template tot the rear
wall. Place tile mounting plate on the wall, making
sure that the tabs are touching the bottom of the
cabinet. Line up the notch and center line on
the mounting plate to the center line on the wall.
[] While holding the mounting plate with one hand,
draw drcles on the wall at holes A, B, ( and D (see
illustration above/aculal plate marked with rerows).
Four holes must be used for mounting.
[]
NOTE: Holes C and D are inside area E. If neither
C nor D is in a stud, find a stud somewhere in area E
and draw a fifth circle to line up with the stud. It is
important to use at least one wood screw mounted
firmly in a stud to support the weight of the inicrowave.
Set the mounting plate aside.
Drill holes on the drcles. If there is a stud, drill a _)&_"
hole tot wood soews. For holes that don't line up with a
stud, drill a %" hole lot toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS
TIME.
10
Installation Instructions
INSTALLATION TYPES
This microwave oven is designed lot adaptation to tile
tollowing three types of ventilation:
A. Outside Top Exhaust (Vertical Duct)
B. Outside Back Exhaust (Horizontal Duct)
C. Recirculating (Non-Vented Ductless)
(Choose A, B or C)
NOTE: This microwave is shipped assembled tot Outside
Top Exhaust (except fin non-vented models). Select tile
type of ventilation required tot your installation and
proceed to that section.
OUTSIDE TOP EXHAUST
(VERTICAL DUCT)
OUTSIDE BACK EXHAUST
(HORIZONTAL DUCT)
Adaptorin Placefor
Outside TopExhaust
RECIRCULATING
(NON-VENTED DUCTLESS)
A Charcoal Fiher Accessory
Kit is required fin the non-
vented exhaust. (See your
Owner's Manual lot tile kit
ntlulbei.)
11
Installation Instructions
OUTSIDE TOP EXHAUST (Vertical Duct)
INSTALLATION OVERVIEW
A 1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Damper Operation
A4. Mount Microwave Oven
A5. Adjust Exhaust Adaptor
A6. Connect Duc/work
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
_=
\
Attach the plate to tile wall using toggle bolts. At least
one wood screw must be used to attach the plate to a
wall stud.
[] Remove tile toggle wings flom the bohs.
[] Insert the bolts into the mounting plate
through tile holes designated to go into (h)_vall
and reattadl the toggle wings to ¾" (19.05 ram)
onto emh bolt.
To use toggle bolts:
SpacingforToggles
MoreThanWall
+l..-.[.--Th ckness
Mounting
Plate
BoltEnd
[] Place tile mounting plate against the wall and
insert tile toggle _dngs into the holes in the wall to
I_lount the plate.
NOTE: Befine tightening toggle bohs and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careflfl to avoid pinching fingers
between the back of the mounting plate and the wall.
[] Tighten all bolts. Pull the plate away flom the wall
to help tighten the bolts.
12
Installation Instructions
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
You need to drill holes for the top support screws, a
hole large enougll for tile power cord to fit through,
and a cutout large enougll for tile exhaust adaptor.
" Read tile instructions on tile TOP CABINET
TEMPI ATE.
• Tape it underneath the top cabinet.
• Drill tile holes, following tile instructions on tile
TOP CABINET TEMPI,ATE.
CAUTION: Wear satety goggles when drilling holes
in the cabinet bottom.
CHECK FOR PROPER
DAMPER OPERATION
BlowerPlate
Exhaust Adaptor
(absent on models shipped
for recirculation exhaust)
_,, Backof
Microwave
• Place tile microwave in its upright position, with tile
top of tile unit thcing up.
• This microwave oven may be shipped assembled tor
top exhaust (adaptor installed) or tor recirculation
exhaust (adaptor absent).
• Make sure tape securing damper is removed and
damper pivots easily before mounting microwave.
" You xdll need to make adjustments to assure proper
alignment _dth your house exhaust duct after tile
microwave is installed.
MOUNT THE MICROWAVE
OVEN
FOR EASIER INSTAIJATION AND PERSONAI,
SAFETY, WE RE( OMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your cabinet is metal, use the nylon
grommet around the power cord hole to prevent
cutting of tile cord.
NOTE: We recommend using fillet blocks if the
cabinet fiont hangs below the cabinet bottom shell
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
NOTE: When mounting
tile ulicI'OWaVe oven,
thread power cord
through hole in bottom of
top cabinet. Keep it tight
throughout Steps 1-3. Do [] IJft inicrowave, tilt it
not pincll cord or lift oven
by pulling (ord. "-- fot_vard, and hook
• slots at back bottom
edge onto Ibm lower
tabs of mounting
plate.
13
_ Rotate flont of oven
up against cabinet
bottom.
[] Insert a self aligning screw through top center
cabinet hole. Temporarily secure the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to bottom of cabinet.
Installation Instructions
CabinetFront
CabinetBottomShelf
FillerBlock
T quivalentto
Depth
of Cabinet
Recess
[] Insert 2 self:aligning screws
through outer top (abinet
holes. Turn two flfll turns on
each screw.
n
[] Tighten center
screw completely.
[] Tighten tile tinter two screws to tile top of tile
microwave oven. (While tightening screws, hold
the microwave oven in pla(e against the wall and
the top cabinet.)
[] Install grease fihers. See the Owner's Manual
parked xdth the mk rowave.
ADJUST THE EXHAUST
ADAPTOR
Open the top cabinet and a([iust tile exhaust adaptor
to connect to the house duct.
Backof
BlowerPlate Damper Microwave
ForFront-to-Backor
Side-to-Side
Adjustment,Slidethe
ExhaustAdaptoras
Needed
_'_ CONNECTING DUCTWORK
HouseDuct
[]Extend the hrmse duct dr)wn tr) cr)nnect to
the exhaust adaptor.
[] Seal exhaust du(t joints using du(t tape.
14
Installation Instructions
OUTSIDE BACK EXHAUST (Horizontal Duct)
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Attach Mounting Plate to Wall
B3. Prepare Top Cabinet
B4. A(ljust Blower
B5. Mount the Microwave Oven
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
[] Place the mounting plate against tile rear wall and
align it with the holes drilled earlier.
[] Using a pencil, put (lots through holes/notches F,
G, H and I (see above illustration). Remove the
mounting plate and draw lines extending through
the points. This will give the location and size of the
box cutout tin the rear wall duct.
[] Use a saw (saber or keyhole) to cut out the opening.
[] Place tile microwave in its upright position with tile
top of the unit lacing up.
This microwave oven is shipped assembled ti)r top
exhaust. You will need the exhaust adaptor fin.
installation in the rear wall opening. To remove the
exhaust adaptor tiom tile microwave oven:
[] Remove tape securing damper.
_ Lift offthe
[] Remove and, blower plate
save screw _, Damper and attached
that holds *,_, adaptor flom
blower plate ,,
tO IIlicI'owave.
[] Slide exhaust adaptor to one side and remove it.
5
Installation Instructions
_-_ PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
(continued)
House
Duct
Damper Hinge On Top
DamperSwings
[_Fit tile exhaust adaptor into the house duct as
shown. Make sure the exhaust adaptor (with the
damper) is squared up in the house duct and lines
up with the holes in the mounting plate.
[]Remove the paper f_om the sticky side of the 28"
(71.12 cm) foam tape. Press the stick) side onto the
face of the exhaust adaptor. (Don't stretch the foam
tape.)
[] Attach the other 28" (71.12 cm) foam tape to the
flont of the mrmnting plate arrmnd both of the
exhaust r)penings where it will tou(h the mi(rr)wave.
I-_ ATTACH THE MOUNTING
IiI
PLATE TO THE WALL
il i
Attach the plate to the wall using toggle bohs. At least
one wood screw must be used to attach the plate to a
wall stud.
[] Remove the toggle wings tiom the bolts.
[] Insert the bolts into the mounting plate through the
holes designated to go into (h)avall and reattach the
toggle wings to _/_"(19.05 ram) onto each bolt.
To use toggle bolts:
Mounting
Plate
Spacing for Toggles More
-_l_-_i_ ThanWallThickness
i
ToggleWings
B01tEnd
[] Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careflfl to avoid pinching fingers
between the back of the mounting plate and the wall.
[] Tighten all bolts. Pull the plate away flom the wall
to help tighten the bolts.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
CABINET
Yrm need to drill holes for the top support screws and
a hole large enr)ugh for the power (ord to fit through.
)
• Read the instmctirms rm the TO1 (_ABINET
TEMPI,ATE.
• Tape it underneath the top cabinet.
• I)rill the hr)les, follr)_dng the instructirms rm the
)
TOP ( ABINET TEM1 LATE.
CAUTION: Wear satety goggles when drilling holes
in the (abinet bottom.
6
Installation Instructions
I-_ ADAPTING MICROWAVE
BLOWER FOR OUTSIDE
BACK EXHAUST
Remove and save screw that holds bh)wer motor
t 0 UlI( I'OW}lVe,
BlowerMotor
__ Backof
_ Micr0wave
-_ BI0werM0t0r
- "_ Screw
[] Careflflly pull out the bh)wer unit. The _dres
_dll extend far enough to alh)w you tr) adjust the
1)lower unit.
BEFORE: Fan Blade
Openings Facing
EndA
[] Rotate bh)wer unit counterch)ckwise 180 °.
BeforeRotation After Rotation
Microwave Microwave
[] (;ently remove the xdres flom the grooves.
Reroute the _dres through grooves on other side
of the bh)wer unit.
BeforeRerouting
Wires R0uted ThroughBightSide
After Rerouting
Wire, Routed ThroughLeft Side
[] Roll the blower unit 90 ° so that fan blade
openings are lacing out the back of the
uliciowave,
BeforeRolling
Backof
Microwave
AfterRolling
Microwave
[] Place the blower unit back into the opening.
AFTER: Fan Blade
Openings Facing Back
EndB __ Ej/_I_jT_____,, _rrd A
CAUTION: Do not pull or stretch the blower
unit wiring. Make sure the wires are not
pinched.
NOTE: The blower unit exhaust
open!ngs should match exhaust
openings on rear of microwave oven.
[]
Se(ure the bh)wer unit tr) the mi(rowave xdth
the screw fl'om Step 1.
Blower Plate
I
I
Backof
Microwave
BlowerMotor
Screw
[] Replace the bh)wer plate in the same position
as before with the screw.
17
Installation Instructions
MOUNT THE MICROWAVE
OVEN
FOR L4SIER INSTAI,IATION AND PERSONAL
SAFETY, WE RECOMMEND THAT TWO PEOPLE
INSTALL THIS MICROWAVE OVEN.
IMPORTANT: Do not grip or use handle
during installation.
NOTE: If your cabinet is metal, use tile nylon
grommet around tile power cord hole to prevent
cutting of tile cord.
NOTE: We recommend using filler blocks if the
cabinet flom hangs below the cabinet bottom shelf.
IMPORTANT: If filler blocks are not
used, case damage may occur from over
tightening screws.
NOTE: When mounting
tile illi(rowave oven,
thread power cord
through hole in bottom of
top cabinet. Keep it tight
y
flu oughout Steps 1-3. Do [] Lift microwave, tilt it
not pinch cord or lift oven finward, and hook
by pulling cord. _ slots at back bottom
edge onto Ibm lower
tabs of mounting
plate.
_ Rotate flont of oven
up against cabinet
bottoln.
[] Insert a self aligning screw through top center
cabinet hole. Temporarily seolre the oven by
turning the screw at least two full turns after the
threads have engaged. (It will be completely
tightened later.) Be sure to keep power cord
tight. Be careful not to pinch the cord, especially
when mounting flush to bottom of cabinet.
CabinetFront
CabinetBottomShelf
FillerBlock
T quivalent
to Depth
ofCabinet
Recess
Self-AligningScrew
[] Insert 2 sell:aligning screws
through outer top cabinet
holes. Turn two flfll turns on
each screw.
[] Tighten center
screw completely.
[] Tighten tile outer two screws to tile top of the
microwave oven. (While tightening screws, hold
tile microwave oven in place against tile wall and
tile top cabinet.)
[] Install grease fihers. See tile Owner's Manual
packed with tile microwave.
18
Installation Instructions
RECIRCULATJNG (Non-Vented #uctJess)
INSTALLATION OVERVIEW
|
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Microwave Assembly
CA.A(ljust Blower
C5. Mount the Microwave Oven _....
/
C6. Install Charcoal Fiher
I-_ ATTACH THE MOUNTING
PLATE TO THE WALL
\
Attach the plate to the wall using toggle bohs. At
least one wood screw must be used to attach the plate
to a wall stud.
[] Remove the toggle xdngs fiom the bohs.
[] Insert the bohs into the mounting plate through
the holes designated to go into dr}_vall and reattach
the toggle xdngs to _Y, ( l,).0a ram) onto each boh.
To use toggle bolts:
SpacingforToggles
MoreThanWall
--,,-I_-,,-j_,_Thickness
Wings
Mounting
Plate
BoltEnd
[] Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall to
mount the plate.
NOTE: Betore tightening toggle bolts and wood
screw, make sure the tabs on the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careflfl to avoid pinching fingers
between the back of the mounting plate and the wall.
[] Tighten all bolts. Pull the plate away flom the wall
to help tighten the bolts.
USE TOP CABINET TEMPLATE
FOR PREPARATION OF TOP
You need to drill holes for the top support screws and
a hole large enough for the power cord to fit through.
• Read the instructions on the TOP (ABINET
TEMPI ATE.
• Tape it underneath the top cabinet.
• Drill the holes, tollowing the instructions on the
TOP CABINET TEMPLATE.
CAUTION: Wear safety goggles when drilling holes
in the cabinet bottoln.
19
Installation Instructions
CHECK MICROWAVE ASSEMBLY
Exhaust Adaptor (absent
on models shipped for
recirculatirm exhaust
Backof
Microwave ;
• Place tile microwave in its upright position, with tile
top of tile unit lacing up.
• The microwave oven may be shipped assembled fin.
top exhaust (adaptor installed) or for recirculation
exhaust (adaptor absent),
" If tile microwave was shipped for recirculation
exhaust, skip to C5. If shipped fin top exhaust,
proceed with (4.
ADAPTING MICROWAVE
BLOWER FOR RECIRCULATION
[] Relnove _._ D_nper [] Lifloffthe
and save , blower plate
screw that ...... and attached
holds adaptor flom
blower the microwave.
,,
plate to
nlicrowave.
ackof
Microwave
[] Slide exhaust adaptor to one side and relnove it.
NOTE: The exhaust adaptor with damper is not
needed for recirculating models. You may want to
save theln for possible fhture use.
Remove and save tile screw that holds tile bh)wer
II1OLOI" 1o tile illiciowave.
_ BlowerPlate
_.___ Backof
<_ _ Microwave
o--....,,.._;,cO=
[] Carefhlly pull out tile bh)wer unit. Tile wires
xdll extend far enough to alh)w you to adjust tile
bh)wer unit.
[] Roll tile bh)wer unit 90 ° so that fan blade
openings
are facing toward the flrmt of the mi(rowave.
BEFORE: Fan Blade
Openings Facing
R011
I
AFTER: Fan Blade
Forward
NOTE: Make sure wires remain routed in tile grooves
of tile motor flame.
20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/