Ohlins HD039S3 Mounting Instruction

Type
Mounting Instruction

Ohlins HD039S3 is a shock absorber designed specifically for Harley Davidson FLH motorcycles. It is built to improve the vehicle's stability and handling, making it an excellent choice for riders who want to enhance their riding experience.

The HD039S3 is engineered with high-quality materials and components, ensuring durability and reliability. It features adjustable spring preload, allowing riders to customize the suspension settings to suit their weight and riding style. The shock absorber also comes with a tool for preload adjustment, making it easy to fine-tune the suspension on the go.

Ohlins HD039S3 is a shock absorber designed specifically for Harley Davidson FLH motorcycles. It is built to improve the vehicle's stability and handling, making it an excellent choice for riders who want to enhance their riding experience.

The HD039S3 is engineered with high-quality materials and components, ensuring durability and reliability. It features adjustable spring preload, allowing riders to customize the suspension settings to suit their weight and riding style. The shock absorber also comes with a tool for preload adjustment, making it easy to fine-tune the suspension on the go.

Shock absorber for Harley Davidson FLH
HD 039S3
Mounting Instructions
Note! 1
Please note that there can be small dierences
between your product and the images in
these instructions.
Note! 1
Please note that during storage and transport,
especially at high ambient temperature, some
of the oil and grease used for assembly may
leak and stain the packaging. This will not cause
damage to the product, wipe o the excessive
oil or grease with a cloth.
Note! 1
Before you install this product, check the kit
contents. If anything is missing, please contact
an Öhlins dealer.
Warning!
Before you install this product, read the Öhlins
Owners manual. This product is an important
part of the vehicle and the vehicle stability.
Kit Contents
Description Part No Pcs
Shock absorber HD 039S3 2
Sleeve 12.7/14/19.5 00123-17 4
Washer 12.8/24/6 03118-08 4
Tool preload adjuster 03199-01 1
Sticker set "ÖHLINS" 10207-01 1
Owners manual 07241-02 1
2
1
Put the motorcycle on a work stand so that the
rear wheel barely touches the ground.
2
Loosen and remove the original shock
absorber.
3
Install the Öhlins shock absorber in the same
position as the original shock absorbers. The
ll screw pointing towards the rear.
Note! 1
Lower the vehicle so that the suspension
is slightly compressed before you tighten
the screws.
Caution!
Make sure that you tighten all screws to the
correct torque and that nothing fouls or restricts
movement of the shock absorber/front fork/
steering damper when the suspension is fully
compressed or extended.
MOUNTING INSTRUCTIONS
Warning!
We strongly recommend to let an Öhlins dealer
install this product.
Warning!
If you work with a lifted vehicle, make sure that it
is safely supported to prevent it from tipping over.
Note! 1
When you work with this product, see the
vehicle service manual for vehicle specic
procedures and important data.
Note! 1
Before you install this product clean the vehicle.
3
MOUNTING INSTRUCTIONS
1
washer 03118-08
washer 03118-08
sleeve 00123-17
cylinder head
end eye
wheel side
wheel side
sleeve 00123-17
Öhlins Asia Co. Ltd
700/937 Moo5, Tambol Nongkhaga,
Amphur Phantong, Chonburi Province
20160 Thailand
© Öhlins Asia Co. Ltd. All rights
reserved. Any reprinting or
unauthorized use without the written
permission of Öhlins Racing AB
is prohibited.
Öhlins products are subject to
continuous improvement and
development, therefore, although
these instructions include the most
up-to-date information available at
the time of printing, minor updates
may occur.
To nd the latest information
contact an Öhlins distributor.
Please contact Öhlins if you have
any questions regarding the
contents in this document.
SETUP DATA
Warning!
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owners Manual before you make
any adjustments. Contact an Öhlins dealer if you
have any questions about setting up.
ADJUSTMENTS
Part no. MI_HD 039S3_EN_0
Issued 2020-09-17
Spring
preload
adjuster
Warning!
Before you ride/drive, always make sure that the
setup is according to the recommended setup
data. Read about adjustments and setting up
in the Öhlins Owner’s Manual before you make
any adjustments. Contact an Öhlins dealer if you
have any questions about setting up.
Spring
Part No ......................................... 66420-030
Free spring length......................... 200 mm.
Spring rate.................................... 30 N/mm
Preload adj.range.......................... [0-32] mm
Shock absorber data
Length .................... 311 mm.
Stroke .................... 79 mm.
Recommended set-up
Spring Preload............................ 13 mm.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Ohlins HD039S3 Mounting Instruction

Type
Mounting Instruction

Ohlins HD039S3 is a shock absorber designed specifically for Harley Davidson FLH motorcycles. It is built to improve the vehicle's stability and handling, making it an excellent choice for riders who want to enhance their riding experience.

The HD039S3 is engineered with high-quality materials and components, ensuring durability and reliability. It features adjustable spring preload, allowing riders to customize the suspension settings to suit their weight and riding style. The shock absorber also comes with a tool for preload adjustment, making it easy to fine-tune the suspension on the go.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI