Cal Spas Swim Spa Owner's manual

LTR20181002, Rev. F

7/2/18

is strictly prohibited.

Cal Spas

®

and Freedom Sound System

™

are registered trademarks.

Due to continuous improvement programs, all models, operation, and/or

specications are subject to change without prior notice.

LTR20181002, Rev. F

7/2/18

CONTACT INFORMATION

For customer service, please contact your

authorized dealer immediately. If you need

additional information and/or assistance, contact:

LMS Customer Service Department

1462 East Ninth Street

Pomona, CA 91766.

Toll Free: 1-800-CAL-SPAS

Fax: 1-909-629-3890

Important Safety Instructions .......1

Preparing for Your New Portable Spa . 2

Pre-Delivery Checklist..................2

Planning the Best Location ..............2

Preparing a Good Foundation ............3

Opening the Front Door Panel

for Electrical Hookup...................3

240 Volt Electrical Installation ...........4

Wiring Requirement/GFCI Wiring

Diagram for US & Canada ...............5

European Wiring Conguration ..........6

120 Volt Electrical Installation ...........7

Testing the 240 Volt GFCI Breaker........7

Filling and Powering Up Your Portable

Spa .................................7

Priming the Pump ....................10

Operating Your Spa ...............11

NEO Control Panel Operation ...........11

Jets................................18

Swim Spa and Swim Workout

Instructions .........................19

Swim Workout Programming ...........19

ATS Plus Therapy System ..............21

Aquatic Air Therapy

TM

(AAT) . . . . . . . . . . . . 22

LED Lighting.........................22

Diverter Knobs.......................23

Air Venturis .........................23

Waterfalls ..........................23

Hydro Streamer Waterfall..............23

Water Clarity ....................24

Water Quality Terms and Denitions .....24

Water Testing Methods ................25

Adding Chemicals to the Spa Water ......26

1. Balancing the Water Chemistry Levels . 26

2. Sanitation and Shock ...............28

3. Filtration .........................29

4. Regularity (Maintenance Schedule)....30

Generic Names for Chemicals ...........30

Common Water Chemistry Questions ....31

Do’s and Don’ts ......................32

Bather Load . . . . . . . . . . . . . . . . . . . . . . . . . 32

Ozonator ...........................32

Troubleshooting Water Clarity Problems ..33

Bromine Generator ...................34

Intelligent Controller Codes for the

Bromine Generator ...................35

Cleaning and Maintenance

and Sound System................36

Removing and Reseating the Pillows .....36

Jet Removal and Replacement ..........36

Draining Your Portable Spa ............37

Winterizing (Cold Climate Draining) .....38

Cleaning and Replacing the Filter........38

Spa Cover...........................38

Vacation Care........................39

Cleaning Your Spa ....................39

Using the Freedom Sound System .......39

Appendix .......................40

Replacement Parts ...................40

Basic Troubleshooting.................53

“Thermal Creep” .....................55

Limited Warranty.....................56

Warranty Registration.................58

Table of Contents

2018 Portable Spa

LTR20181002, Rev. F

Read This First!

www.calspas.com

1

Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS.

DANGER -- Risk of accidental drowning:

Do not allow children to be in or around a spa unless a

responsible adult supervises them. Keep the spa cover

on and locked when not in use. See instructions enclosed

with your cover for locking procedures.

DANGER -- Risk of injury:

The suction ttings in this spa are sized to match the

specic water ow created by the pump. Should the need

arise to replace the suction ttings, or the pump, be sure

the ow rates are compatible.

Never operate the spa if the suction tting or lter baskets

are broken or missing. Never replace a suction tting with

one that is rated less than the ow rate marked on the

original suction tting.

DANGER -- Risk of electric shock:

Install the spa at least 5 feet (1.5 meters) from all metal

surfaces. As an alternative, a spa may be installed within 5

feet of metal surfaces if each metal surface is permanently

bonded by a minimum #8 AWG solid copper conductor to

the outside of the spa’s control box.

Do not permit any external electrical appliances, such as

lights, telephones, radios, televisions, and etc., within ve

feet (1.5 meters) of the spa. Never attempt to operate any

electrical device from inside the spa.

Replace a damaged power cord immediately.

Do not bury the power cord.

Connect to a grounded, grounding-type receptacle only.

HYPERTHERMIA DANGER:

Prolonged exposure to hot air or water can induce

hyperthermia. Hyperthermia occurs when the internal

temperature of the body reaches a level 3˚F to 6˚F above

the normal body temperature of 98.6˚F (or 2˚C to 4˚C

above 37˚C). While hyperthermia has many health benets,

it is important not to allow your body’s core temperature to

rise above 103˚F (39.5˚C).

Symptoms of excessive hyperthermia include dizziness,

lethargy, drowsiness and fainting. The eects of excessive

hyperthermia may include:

• Failure to perceive heat

• Failure to recognize the need to exit spa or hot tub

• Unawareness of impending hazard

• Fetal damage in pregnant women

• Physical inability to exit the spa

• Unconsciousness

WARNING: The use of alcohol, drugs, or medication can

greatly increase the risk of fatal hyperthermia.

The spa water should never exceed 104˚F (40˚C). Water

temperatures between 100˚F (38˚C) and 104˚F (40˚C)

are considered safe for a healthy adult. Lower water

temperatures are recommended for young children and

when spa use exceeds 10 minutes.

High water temperatures have a high potential for causing

fetal damage during pregnancy. Women who are pregnant,

or who think they are pregnant, should always check with

their physician prior to spa usage.

The use of alcohol, drugs or medication before or during

spa use may lead to unconsciousness, with the possibility

of drowning.

Persons suering from obesity, a medical history of heart

disease, low or high blood pressure, circulatory system

problems or diabetes should consult a physician before

using the spa.

Persons using medications should consult a physician

before using the spa since some medications may induce

drowsiness while others may aect heart rate, blood

pressure and circulation.

WARNING -- To reduce the risk of injury:

WARNING: People with infectious diseases should not use

a spa or hot tub.

WARNING: To avoid injury, exercise care when entering or

exiting the spa or hot tub.

WARNING: Do not use drugs or alcohol before or during

the use of a spa or hot tub to avoid unconsciousness and

possible drowning.

WARNING: Do not use a spa or hot tub immediately

following strenuous exercise.

WARNING: Prolonged immersion in a spa or hot tub may

be injurious to your health.

CAUTION: Maintain water chemistry in accordance with

manufacturer’s instructions.

SAVE THESE INSTRUCTIONS.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

2

Most cities and counties require permits for exterior

construction and electrical circuits. In addition, some

communities have codes requiring residential barriers such

as fencing and/or self-closing gates on property to prevent

unsupervised access to the property by children. Your dealer

can provide information on which permits may be required

and how to obtain them prior to the delivery of your spa.

Before Delivery

Plan your delivery route

Choose a suitable location for the spa

Lay a 5 - 8 cm concrete slab

Install dedicated electrical supply

After Delivery

Place spa on slab

Connect electrical components

Preparing for Your New Portable Spa

Pre-Delivery Checklist

Planning the Best Location

Safety First

Consider How You Will Use Your Spa

Plan for Your Environment

Consider Your Privacy

Provide a View with Your Spa

Keep Your Spa Clean

Allow for Service Access

Do not place your spa within 10 feet (3 m) of overhead

power lines.

How you intend to use your spa will help you determine

where you should position it. For example, will you use

your spa for recreational or therapeutic purposes? If your

spa is mainly used for family recreation, be sure to leave

plenty of room around it for activity. If you will use it for

relaxation and therapy, you will probably want to create a

specic mood around it.

If you live in a region where it snows in the winter or rains

frequently, place the spa near a house entry. By doing

this, you will have a place to change clothes and not be

uncomfortable.

In a cold-weather climate, bare trees won’t provide

much privacy. Think of your spa’s surroundings during all

seasons to determine your best privacy options. Consider

the view of your neighbors as well when you plan the

location of your spa.

Think about the direction you will be facing when sitting in

your spa. Do you have a special landscaped area in your

yard that you nd enjoyable? Perhaps there is an area

that catches a soothing breeze during the day or a lovely

sunset in the evening.

In planning your spa’s location, consider a location where

the path to and from the house can be kept clean and

free of debris.

Prevent dirt and contaminants from being tracked into

your spa by placing a foot mat at the spa’s entrance where

the bathers can clean their feet before entering your spa.

Make sure the spa is positioned so that access to the

equipment compartment and all side panels will not be

blocked.

Many people choose to install a decorative structure

around their spa. If you are installing your spa with

any type of structure on the outside, such as a gazebo,

remember to allow access for service. It is always best

to design special installations so that the spa can still be

moved, or lifted o the ground.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

3

Your spa needs a solid and level foundation. The area

that it sits on must be able to support the weight of the

spa, with water and the occupants who use it. If the

foundation is inadequate, it may shift or settle after the

spa is in place, causing stress that could DAMAGE YOUR

SPA SHELL AND FINISH.

Damage caused by inadequate or improper

foundation support is not covered by the

warranty. It is the responsibility of the spa

owner to provide a proper foundation for the

spa.

Place the spa on an elevated 3 to 4” / 30 cm concrete slab.

Pavers, gravel, brick, sand, timbers or dirt foundations are

not adequate to support the spa.

We strongly recommend that a qualied, licensed

contractor prepare the foundation for your spa.

Preparing a Good Foundation

If you are installing the spa indoors, pay close attention

to the ooring beneath it. Choose ooring that will not be

damaged or stained.

If you are installing your spa on an elevated wood deck or

other structure, it is highly recommended that you consult

a structural engineer or contractor to ensure the structure

will support the weight of 150 pounds per square foot (732

kg / m2).

To properly identify the weight of your new spa when full,

remember water weighs 8.33 lbs. per gallon, or 1 kg per

liter. For example, an average 8’ spa holds approximately

500 gallons, or 1892 liters, of water. Using this formula, you

will nd that the weight of the water alone is 4,165 lbs, or

1892 kg. Combined with the dry weight of the spa you will

note that this spa will weigh approximately 5,000 lbs, or

2267 kg, when full of water.

Opening the Front Door Panel for Electrical Hookup

The following electrical connections must be

performed by a licensed electrical contractor. Unscrew

and remove the two corner panels on each side of the spa’s

front door.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

4

All 240V spas must be permanently connected (hard wired)

to the power supply. See the GFCI and wiring requirements

on page 5.

These instructions describe the only acceptable

electrical wiring procedure. Spas wired in any other

way will void your warranty and may result in serious

injury.

When installed in the United States, the electrical wiring of

this spa must meet the requirements of NEC 70 and any

applicable local, state, and federal codes.

The electrical circuit must be installed by an

electrical contractor and approved by a local building

or electrical inspector.

240 Volt Electrical Installation

Failure to comply with state and local codes may

result in re or personal injury and will be the sole

responsibility of the spa owner.

The power supplied to the spa must be on a dedicated

GFCI protected circuit as required by NEC 70 with no other

appliances or lights sharing the power.

Use copper wire with THHN insulation. Do not use aluminum

wire.

Use the table below to determine your GFCI and wiring

requirements.

Wires that run over 100 feet must increase wire gauge to

the next lower number. For example: A normal 50 amp

GFCI with four #6 AWG copper wires that run over 100 feet

would require you to go to four #4 AWG copper wires.

Reach in and pull the drain assembly through by a few

inches. Carefully unscrew the black outer drain knob and

then unscrew and remove the front door panel.

Pictured to the right is the inside of the spa behind the

front door. The electrician now has access to connect the

spa for power. While the front door is o, refer to page 6

for instructions on ensuring the plumbing ttings are secure

(but do not be tempted to over-torque or over-tighten these

ttings).

Pull the drain pipe through the front door panel, reattach the black outer drain knob and pull the drain assembly back inside

so that the knob is ush with the panel again. Reattach and screw panels back in. (Front door rst, then corner panels)

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

5

Wiring Requirement/GFCI Wiring Diagram for US & Canada

Control System GFCI Required Wires Required

NEO 2100

One 60 amp GFCI -

SIEMENS brand

Four #6 AWG copper wires

See the Cal Spas Pre-Delivery Guide for more information on spa placement for service

access and electrical service.

www.calspas.com/manuals

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

6

European Wiring Conguration

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

7

Always follow applicable local, state and federal codes

and guidelines.

Use only a dedicated electrical line with a 15 amp

breaker.

Cord-and-plug connections may not use a cord longer

than 15 feet (4.6 m) and must be plugged into a

dedicated 15 amp GFCI connection (NEC 680.42(A)

(2)). Do not use extension cords!

Always use a weatherproof-covered receptacle.

Receptacle shall be located not less than 5 feet (1.5

m) from and not exceeding 10 feet (3.0 m) from the

inside wall of the spa. (NEC 680.43(A))

Do not bury the power cord. If your cord becomes

damaged, replace it before next usage.

All 120V spas must have a GFCI. This can be either a

15 amp GFCI receptacle or a 15 amp GFCI cord and

plug kit as shown (CKIT110 - P/N ELE09700086).

Test the GFCI breaker prior to rst use and periodically when the spa is powered. To test the GFCI breaker follow these

instructions (spa should be operating):

1. Press the TEST button on the GFCI. The GFCI will trip and the spa will shut o.

2. Reset the GFCI breaker by switching the breaker to the full OFF position, wait a moment, then turn the breaker back

on. The spa should have power again.

120 Volt Electrical Installation

Testing the 240 Volt GFCI Breaker

Testing the GFCI plug

Test the GFCI plug prior to

rst use and periodically

when the spa is powered.

1. Plug in the GFCI into

the power outlet. The

indicator should turn on.

2. Press the TEST button.

The GFCI will trip, the

indicator will turn o,

and the spa will stop

operating.

3. Press the RESET button. The GFCI will reset, the indicator will

turn on again, and the spa will turn back on.

The spa is now safe to use.

If the GFCI trips while the spa is in use, press the RESET button.

If the GFCI does not reset, unplug the spa and call your local Cal

Spas dealer for service. DO NOT USE THE SPA!

Inspect all plumbing connections in the

equipment area of your spa.

• Make sure unions in the equipment pack are tight. (Be careful

not to over-tighten the plumbing ttings.)

• If your spa has gate

valves, make sure they

are all in the UP or OPEN

position.

• Make sure the drain

valve is closed and

capped. (See page 37 for

a description of drain

valves.)

Filling and Powering Up Your Portable Spa

Never run the spa with the gate valves closed or without

water circulating for long periods of time.

1. Inspect the spa equipment.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

8

3. Fill the spa.

2. Remove the cartridge from lter canister.

Never ll your spa with soft water.

Soft water makes it impossible to maintain the proper water chemistry and may cause the water to foam, which

will ultimately harm the nish of the spa and void your warranty.

After you remove the lter, remove the plastic

wrapper and soak it in water for 30 minutes before

you replace it. A dry lter can allow air into the

ltration system which can cause the pump to fail

to prime.

If you have a skimmer like this:

Rotate and remove the black locking ring. Remove the

black skimmer cap and barrel, grip the lter by the

handle and unscrew it from the canister.

Replace and lock the locking ring and slide the skimmer

cap and barrel back in the canister.

Note: The skimmer cap and barrel were locked in place

at the factory to prevent damage during shipment. It

must be unlocked and replaced in the lter canister so that

it can oat when the spa is lled. If you do not remove the

cap and barrel, your spa’s ltration system will not perform

as it was designed to.

Place a garden hose in the lter canister and ll your spa.

Always ll the spa through the lter canister. Failure

to do so may cause air to be trapped in the ltration system

and prevent the pumps from operating properly.

Fill the spa until water level is about six inches from the top.

If the water level is too low or too high, your spa will not

operate properly.

Teleweir Mega

lter skimmer

• 75 square feet

ltration

• Smooth cap

Teleweir lter

skimmer

• 50 square feet

ltration

• Spoked cap

If you have a skimmer like this:

Grip the lter by the handle and unscrew it from the

canister. Never try to pull the lter cartridge while the spa

is running in low or high speed (i.e., any speed).

If you have a skimmer like this:

Remove the black skimmer cap and barrel, grip the lter

by the handle and unscrew it from the canister.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

9

5. Prime the pump.

4. Turn on power to the spa.

6. Install the lter into the lter canister.

Make sure the lter has soaked at least 30 minutes

before you install it. Insert the lter all the way and

screw it in. Do not over-torque the cartridge during

installation, just hand tighten gently.

The system will enter the priming mode. Priming Mode will

display on the control panel. In Priming Mode, all devices such

as jets and lights are operable. Jets can be turned on and o to

help prime the pump. The system will exit Priming Mode and go

to the Main display when the RETURN button is pressed, or after

four minutes of inactivity.

Test and adjust the water chemistry. See the section on

page 21 for instructions on keeping your water clear.

Spa owners with the bromine generator need to follow the

instructions on page 34.

When the spa is lled to the correct level, turn on the power at

the GFCI breaker. (Ensure that the 120V spas are connected to

the proper electrical outlet.)

7. Adjust water chemistry.

8. Let the spa heat up.

When the spa has nished priming, the heater will

activate. Put the cover on and let the spa heat to the set

temperature.

2018 Portable Spa

LTR20181002, Rev. F

Preparing for Your New Portable Spa

www.calspas.com

10

New spa owners often have diculty the rst time they start their spa

and the pump fails to prime. This can be frustrating, but these simple

instructions can help you.

Sometimes air can become trapped in the pump while lling the spa. You

will know this has happened when after you have lled and started the spa,

the pump does not seem to function. You will hear the pump operating, but no water will be moving.

The pump will not work

properly while air is trapped in it.

Continuing to operate the pump

in this way will cause damage.

Starting Up: Priming Mode for NEO-Pack Systems

Exiting Priming Mode for NEO-Pack Systems

Priming the Pump

Bleeding Air from the Pump

If you have tried priming the pump several times unsuccessfully using the

control panel, you can bleed the air from the pump manually.

1. Shut o the power to the spa.

2. Using a Phillips screwdriver, remove the front panel from the spa and

locate the pump.

3. Close the gate valve on the discharge side of the pump (if your spa is

installed with one.)

4. Turn the bleeder valve counter clockwise with a small pair of pliers until

the air has been released from the pump.

5. If this is unsuccessful, loosen the union nut on side of the pump with

channel locks. When air is bled out, tighten the nut.

6. Turn on power to the spa and press the JETS button. If there is still air

trapped in the pump, repeat steps 2 through 5 until the pump primes.

The system will enter the priming mode. Priming Mode will display on the control panel. In Priming Mode, all devices

such as jets and lights are operable. Jets can be turned on and o to help prime the pump. The system will exit Priming

Mode and go to the Main display when the RETURN button is pressed, or after four minutes of inactivity.

You can manually exit Priming Mode by pressing the RETURN button. Note that if you do not manually exit the priming

mode, the priming mode will be automatically terminated after 4 to 5 minutes. Be sure that the pumps have been primed

by this time.

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

11

NEO Control Panel Operation

Operating Your Spa

Primary Navigation and Functions of NEO Two-pump System

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

12

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

13

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

14

Settings Screens

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

15

Error Screens

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

16

Operating the NEO Wi-Fi App

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

17

2018 Portable Spa

LTR20181002, Rev. F

Operating Your Spa

www.calspas.com

18

Connecting to a Device or Network

3

2

1

Your

spa

Wi-

signal

Phone or

other

device

Your home

network

router

Internet cloud

connection

Local wi-

connection

3G or 4G

Internet

Local hotspot

Wi-

Direct connection

Range: About 20 feet

Range limit: Limited to the range

of the wi- module

HOW TO CONNECT TO IT:

Install the app on your phone or device -- see the following section “Installing the app”.

Through a network with internet access, using

Cloud connection or other hotspot connection

HOW TO CONNECT TO IT:

Follow connection instructions from section (2) above. The Cloud icon appears

automatically when network connection is made. You can then connect to the

spa’s wi- module.

Range: Worldwide

Range limit: Limited to 3G / 4G / hotspot

availability

Through home network with no internet access

Range: About 50 feet

Range limit: Limited to the range of your

home router’s signal

Allows one local connection at a time

HOW TO CONNECT TO IT:

1. Install the app on your phone or device.

2. Exit the app and go to wi- settings on your phone or device.

3. Select and enable your local router.

4. Start the app. After you connect, select Settings on the home screen.

5. On the Settings screen, select Advanced, then on the Advanced screen, select Wi- Settings.

6. On the Wi- screen, select WPA. Then select the name of your home router from the drop-down menu.

7. Enter the SSID and Key for your router, the tap Save and select OK twice.

8. Close the app and re-start it to connect to your home network.

Allows unlimited simultaneous connections

Jets

Almost all of the jets in your spa are adjustable. Rotating

the face of an adjustable jet to the left (counterclockwise)

will decrease the amount of water ow through the

jet. Rotating the face of an adjustable jet to the right

(clockwise) will increase the amount of water ow through

the jet. (See example shown here.)

Neck jets adjust in the opposite directions (counterclockwise

to increase, clockwise to decrease).

Page is loading ...

Cal Spas Swim Spa Owner's manual

Cal Spas Swim Spa Owner's manual

Related papers

Other documents